---------------------------------------------------------- Zenith-List Digest Archive --- Total Messages Posted Mon 12/22/03: 6 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 04:50 AM - Re: Roll Bar (Bob Miller) 2. 07:07 AM - 601/0-200 (james Neely) 3. 08:24 AM - Re: Roll Bar (88tierra) 4. 03:10 PM - AreoFlash Wiring Diagram () 5. 03:17 PM - Re: Roll Bar () 6. 07:21 PM - Re: AreoFlash Wiring Diagram (Al Young) ________________________________ Message 1 _____________________________________ Time: 04:50:04 AM PST US From: "Bob Miller" Subject: Re: Zenith-List: Roll Bar --> Zenith-List message posted by: "Bob Miller" Sounds like several of us are considering the idea. When we get to the actual design stage, maybe we could all submit our designs to Chris and post his feedback to the list. That way we might get the benefit of multiple possibilities. Bob Miller ----- Original Message ----- From: "Eric Tauch" Subject: Re: Zenith-List: Roll Bar > --> Zenith-List message posted by: "Eric Tauch" > > I also remember seeing some diagrams. I thought it was in the Zenair > Newsletter, but after searching all the > back-issues I could find, I think the pictures may have been on someones > website. > > I remember them because the diagrams (I think) came from Chris Heinz, and > were rather crude pencil > drawings. > > They were essentially square at the top roll-bars, one for each seat. Sort > of like the ones you see in sports > cars. > > This is my recollection, which may not be accurate. Would appreciate if > anyone else has any info on these > type. I plan on putting something in my 601XL (roll-bar). > > > Thanks, > > Eric > ----- Original Message ----- > From: "Carlos Sa" > To: > Subject: Re: Zenith-List: Roll Bar > > > > --> Zenith-List message posted by: Carlos Sa > > > > Bob, did you search the archives? > > > > I remember discussions around that theme a while back (years?). > > I think Peter (?) Chapman had some ideas. > > > > > > Carlos > > > > do not archive > > > > > > > > ________________________________ Message 2 _____________________________________ Time: 07:07:14 AM PST US From: "james Neely" Subject: Zenith-List: 601/0-200 --> Zenith-List message posted by: "james Neely" For those of you who have mounted an 0-200 in your 601: I'm looking for feedback, tips, tricks, general advice for this installation. eg. what nose bowl did you use?, what was final weight ff? etc. Mine is a taildragger HD Thanx James ________________________________ Message 3 _____________________________________ Time: 08:24:48 AM PST US From: "88tierra" Subject: RE: Zenith-List: Roll Bar --> Zenith-List message posted by: "88tierra" Is anyone considering a roll bar looking into incorporating a ballistic chute into the design? Larry K Bellevue, IA 601XL Wanna Builder -----Original Message----- From: owner-zenith-list-server@matronics.com [mailto:owner-zenith-list-server@matronics.com] On Behalf Of Bob Miller Subject: Re: Zenith-List: Roll Bar --> Zenith-List message posted by: "Bob Miller" --> Sounds like several of us are considering the idea. When we get to the actual design stage, maybe we could all submit our designs to Chris and post his feedback to the list. That way we might get the benefit of multiple possibilities. Bob Miller ________________________________ Message 4 _____________________________________ Time: 03:10:08 PM PST US From: Subject: Zenith-List: AreoFlash Wiring Diagram Seal-Send-Time: Mon, 22 Dec 2003 17:08:49 -0600 --> Zenith-List message posted by: I recently acquired an AeroFlash wingtip strobe/nav light set, but unfortunately, some of the wires were unplugged, rather than cut. Thus, I have the strobe light with a red, black and white wire, and a three-wire female connector mounted on the strobe's power supply. Since I regard light bulbs as sorcery, and regularly sacrifice a rubber chicken (they last longer) before turning on my computer, I figure I'd better ask before proceeding to fry the whole thing. Does anybody have a wiring diagram, or remember, which wire goes where into the female connector, starting from, say, the base of the power supply? Any help would be appreciated. Paul Rodriguez Corvair'd 601XL, wings almost ready for skin ________________________________ Message 5 _____________________________________ Time: 03:17:20 PM PST US From: Subject: Re: Zenith-List: Roll Bar Seal-Send-Time: Mon, 22 Dec 2003 17:16:40 -0600 --> Zenith-List message posted by: Actually, yes, but it's important to note that the two don't equate. A BRS will get you down relatively safely, and (hopefully) right side up. The roll bar protects you in what might delicately be referred to as a zero AGL half-loop. I like the idea of an extra reinforcement at the front of the baggage compartment, and will look seriously into it when I get that far. I would guess somebody has already done it. Paul Rodriguez Corvair'd 601XL, wings almost ready ----- Original Message ----- From: 88tierra To: zenith-list@matronics.com Sent: Monday, December 22, 2003 10:24 AM Subject: RE: Zenith-List: Roll Bar --> Zenith-List message posted by: "88tierra" Is anyone considering a roll bar looking into incorporating a ballistic chute into the design? Larry K Bellevue, IA 601XL Wanna Builder -----Original Message----- From: owner-zenith-list-server@matronics.com [mailto:owner-zenith-list-server@matronics.com] On Behalf Of Bob Miller To: zenith-list@matronics.com Subject: Re: Zenith-List: Roll Bar --> Zenith-List message posted by: "Bob Miller" --> Sounds like several of us are considering the idea. When we get to the actual design stage, maybe we could all submit our designs to Chris and post his feedback to the list. That way we might get the benefit of multiple possibilities. Bob Miller ________________________________ Message 6 _____________________________________ Time: 07:21:14 PM PST US From: "Al Young" Subject: Re: Zenith-List: AreoFlash Wiring Diagram --> Zenith-List message posted by: "Al Young" Paul- The red wire goes into the #1 of the female plug. The black goes into the #2 (middle) and the white goes into the #3. The #1 slot if not marked with a #1, is the one above the ridge on the outside of the plug. Hope this helps. Al Young 601XL 'bout done with the fuselage.