Today's Message Index:
----------------------
1. 01:51 AM - Skyshop--601XL composite landing gear (danny@skyshops.org)
2. 02:12 PM - Re: Re: Oil temp. on 701 of 130oF (daberti)
3. 03:55 PM - 6061-t6 in Canada (Bill Stuart)
4. 04:06 PM - Re: 6061-t6 in Canada (Cdngoose)
5. 04:14 PM - Re: 6061-t6 in Canada (Bill Stuart)
6. 05:10 PM - Re: [Bulk] Re: 6061-t6 in Canada (Paul Riedlinger)
7. 06:56 PM - Aluminum in Canada (Howard Carter)
8. 07:52 PM - Re: [Bulk] Re: 6061-t6 in Canada (Cdngoose)
9. 08:15 PM - Re: 6061-t6 in Canada (John Montgomery)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Skyshop--601XL composite landing gear |
--> Zenith-List message posted by: danny@skyshops.org
Unfortunately we do not sell 601XL composite landing gear . The reason we
dont sell the composite landing gear is because it will not fit the US
version of the 601XL. The system is completely different for attaching and
would have to be installed early stages of assembly of the fuselage. In
addition this modification is not approved by Zenith. Therefore we are not
offering this to the US market at this time.
Thanks for all the support during the year.
Merry Christmas and Happy New Year from Danny & Zaneta
www.Skyshop.org
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Oil temp. on 701 of 130oF |
--> Zenith-List message posted by: "daberti" <daberti@sbcglobal.net>
The altimeter is adjustable. The archives have the procedure
Do not archive
-----Original Message-----
From: owner-zenith-list-server@matronics.com
[mailto:owner-zenith-list-server@matronics.com]On Behalf Of John M.
Goodings
Subject: Zenith-List: Re: Oil temp. on 701 of 130oF
--> Zenith-List message posted by: "John M. Goodings" <goodings@yorku.ca>
I second the advice that you should check the reliability of your
temperature gauge before blocking off the coolant radiator. 130oF sounds
really rather unbelievably low. I have had five faulty gauges, nearly all
of which had to be replaced, and all of which, of course, were out of
warranty. These included the tach for my 912S (Mitchell, read about 2/3
of the correct value, and nearly cost me the engine), a magnetic compass
(Airpath, Southern Field, there was one point where it stuck), an oil
pressure gauge (VDO, it reads 2/3 of the correct value, checked with an
accurate pressure gauge in the line with the engine running; I am living
with this one, because I know it reads 40 psi when the correct value is
60), non-sensitive altimeter (UMA, read 300 feet low), and a 30-0-30
ammeter (VDO, would not centre, but this one was partly my fault). All
were new instruments when installed, although several had been sitting on
a shelf in my (heated) basement for several years (thus, out of warranty).
I am rather ticked about this; it has been expensive. Thus, from my
experience, it is reasonable to suspect a faulty gauge!
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | 6061-t6 in Canada |
--> Zenith-List message posted by: "Bill Stuart" <billstuart25@hotmail.com>
Hello list.
I am plans building a 701sp here in Canada , and have run into a prob that
other builders have no doubt had ,i purchased just enough material from
Aircraft Spruce to build the rudder.Their service was excellent except when
i received my shipment , ups charged me , 22.27 gst , 37.55 ,brokerage fee
and another 2.63 gst on the brok fee,s , needless to say i have learned a
valuable lesson ,(expensive too).
Does anyone in Canada know of a place to buy 6061 ?
Regards
Bill Stuart.
ch701sp
sn 75664
just started the rudder ,
in no rush ,planning on abt 5years to complete.
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | 6061-t6 in Canada |
--> Zenith-List message posted by: "Cdngoose" <601xl@sympatico.ca>
Bill we need a location for you to be able to hone in on a local
distributor
Mark Townsend
Alma, Ontario
Zodiac 601XL EJ 2.2L
Osprey 2 serial # 751
www.ch601.org
www.Osprey2.com
-----Original Message-----
From: owner-zenith-list-server@matronics.com
[mailto:owner-zenith-list-server@matronics.com] On Behalf Of Bill Stuart
Subject: Zenith-List: 6061-t6 in Canada
--> Zenith-List message posted by: "Bill Stuart"
<billstuart25@hotmail.com>
Hello list.
I am plans building a 701sp here in Canada , and have run into a prob
that
other builders have no doubt had ,i purchased just enough material from
Aircraft Spruce to build the rudder.Their service was excellent except
when
i received my shipment , ups charged me , 22.27 gst , 37.55 ,brokerage
fee
and another 2.63 gst on the brok fee,s , needless to say i have learned
a
valuable lesson ,(expensive too).
Does anyone in Canada know of a place to buy 6061 ?
Regards
Bill Stuart.
ch701sp
sn 75664
just started the rudder ,
in no rush ,planning on abt 5years to complete.
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | 6061-t6 in Canada |
--> Zenith-List message posted by: "Bill Stuart" <billstuart25@hotmail.com>
Mark , i live in Moncton , New Brunswick
>From: "Cdngoose" <601xl@sympatico.ca>
>Reply-To: zenith-list@matronics.com
>To: <zenith-list@matronics.com>
>Subject: RE: Zenith-List: 6061-t6 in Canada
>Date: Sat, 25 Dec 2004 19:06:39 -0500
>
>--> Zenith-List message posted by: "Cdngoose" <601xl@sympatico.ca>
>
>Bill we need a location for you to be able to hone in on a local
>distributor
>
>Mark Townsend
>Alma, Ontario
>Zodiac 601XL EJ 2.2L
>Osprey 2 serial # 751
>www.ch601.org
>www.Osprey2.com
>
>-----Original Message-----
>From: owner-zenith-list-server@matronics.com
>[mailto:owner-zenith-list-server@matronics.com] On Behalf Of Bill Stuart
>To: zenith-list@matronics.com
>Subject: Zenith-List: 6061-t6 in Canada
>
>--> Zenith-List message posted by: "Bill Stuart"
><billstuart25@hotmail.com>
>
>Hello list.
>
>I am plans building a 701sp here in Canada , and have run into a prob
>that
>other builders have no doubt had ,i purchased just enough material from
>
>Aircraft Spruce to build the rudder.Their service was excellent except
>when
>i received my shipment , ups charged me , 22.27 gst , 37.55 ,brokerage
>fee
>and another 2.63 gst on the brok fee,s , needless to say i have learned
>a
>valuable lesson ,(expensive too).
> Does anyone in Canada know of a place to buy 6061 ?
>
>
>Regards
>
>Bill Stuart.
>
>ch701sp
>sn 75664
>just started the rudder ,
>in no rush ,planning on abt 5years to complete.
>
>
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | 6061-t6 in Canada |
--> Zenith-List message posted by: "Paul Riedlinger" <paulried@rogers.com>
I am in the same boat as Bill. I am in Toronto and would love to find a
local aluminium supplier.
Paul Riedlinger
paulried@rogers.com
-----Original Message-----
From: owner-zenith-list-server@matronics.com
[mailto:owner-zenith-list-server@matronics.com] On Behalf Of Cdngoose
Subject: [Bulk] RE: Zenith-List: 6061-t6 in Canada
--> Zenith-List message posted by: "Cdngoose" <601xl@sympatico.ca>
Bill we need a location for you to be able to hone in on a local
distributor
Mark Townsend
Alma, Ontario
Zodiac 601XL EJ 2.2L
Osprey 2 serial # 751
www.ch601.org
www.Osprey2.com
-----Original Message-----
From: owner-zenith-list-server@matronics.com
[mailto:owner-zenith-list-server@matronics.com] On Behalf Of Bill Stuart
Subject: Zenith-List: 6061-t6 in Canada
--> Zenith-List message posted by: "Bill Stuart"
<billstuart25@hotmail.com>
Hello list.
I am plans building a 701sp here in Canada , and have run into a prob
that
other builders have no doubt had ,i purchased just enough material from
Aircraft Spruce to build the rudder.Their service was excellent except
when
i received my shipment , ups charged me , 22.27 gst , 37.55 ,brokerage
fee
and another 2.63 gst on the brok fee,s , needless to say i have learned
a
valuable lesson ,(expensive too).
Does anyone in Canada know of a place to buy 6061 ?
Regards
Bill Stuart.
ch701sp
sn 75664
just started the rudder ,
in no rush ,planning on abt 5years to complete.
Message 7
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Aluminum in Canada |
--> Zenith-List message posted by: Howard Carter <howado@cwia.com>
Give a call to Gilles Boulanger at Dedalius Aviation at 819-563-4121.
He knows the sources and costs in Canada.
Howard Carter
CH701sp
do not archive
Message 8
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | 6061-t6 in Canada |
--> Zenith-List message posted by: "Cdngoose" <601xl@sympatico.ca>
Bill I can't help you out but I see that Howard can offer some
assistance. Paul contact Al Etherington as he is in your area and may be
able to find a closer dealer but if not then contact Golden Triangle
Specialty Metals in Cambridge. That is who I but my metal from and I
have not been able to find a cheaper supplier locally with the 6061 in
stock.
Mark Townsend
Alma, Ontario
Zodiac 601XL EJ 2.2L
Osprey 2 serial # 751
www.ch601.org
www.Osprey2.com
-----Original Message-----
From: owner-zenith-list-server@matronics.com
[mailto:owner-zenith-list-server@matronics.com] On Behalf Of Paul
Riedlinger
Subject: RE: [Bulk] RE: Zenith-List: 6061-t6 in Canada
--> Zenith-List message posted by: "Paul Riedlinger"
<paulried@rogers.com>
I am in the same boat as Bill. I am in Toronto and would love to find a
local aluminium supplier.
Paul Riedlinger
paulried@rogers.com
-----Original Message-----
From: owner-zenith-list-server@matronics.com
[mailto:owner-zenith-list-server@matronics.com] On Behalf Of Cdngoose
Subject: [Bulk] RE: Zenith-List: 6061-t6 in Canada
--> Zenith-List message posted by: "Cdngoose" <601xl@sympatico.ca>
Bill we need a location for you to be able to hone in on a local
distributor
Mark Townsend
Alma, Ontario
Zodiac 601XL EJ 2.2L
Osprey 2 serial # 751
www.ch601.org
www.Osprey2.com
-----Original Message-----
From: owner-zenith-list-server@matronics.com
[mailto:owner-zenith-list-server@matronics.com] On Behalf Of Bill Stuart
Subject: Zenith-List: 6061-t6 in Canada
--> Zenith-List message posted by: "Bill Stuart"
<billstuart25@hotmail.com>
Hello list.
I am plans building a 701sp here in Canada , and have run into a prob
that
other builders have no doubt had ,i purchased just enough material from
Aircraft Spruce to build the rudder.Their service was excellent except
when
i received my shipment , ups charged me , 22.27 gst , 37.55 ,brokerage
fee
and another 2.63 gst on the brok fee,s , needless to say i have learned
a
valuable lesson ,(expensive too).
Does anyone in Canada know of a place to buy 6061 ?
Regards
Bill Stuart.
ch701sp
sn 75664
just started the rudder ,
in no rush ,planning on abt 5years to complete.
Message 9
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: 6061-t6 in Canada |
--> Zenith-List message posted by: John Montgomery <1armbandit@rogers.com>
Bill,
In your area try to find a manufacturer or metal supplier who uses
aluminium or other metals, ie. a shop that builds milk trucks or
pressure vessels, etc. If they cannot supply you with 6061, they
probably can tell you who deals with metal stock in the Maritimes.
Probably located in either Moncton, Truro, or most likely Halifax/Dartmouth.
In my case here in Ottawa the metal supplier I was referred to is a
manufacturerer of stainless steel kitchen counters, steam lines,
institutional kitchen gear, etc. They use a wide variety of metals and
also sell metals to the public. I put an order in and 2 weeks later
they got it in from Montreal with their regular shipment.
regards,
John M., Ottawa, Canada
Bill Stuart wrote:
>--> Zenith-List message posted by: "Bill Stuart" <billstuart25@hotmail.com>
>
>Hello list.
>
>I am plans building a 701sp here in Canada , and have run into a prob that
>other builders have no doubt had ,i purchased just enough material from
>Aircraft Spruce to build the rudder.Their service was excellent except when
>i received my shipment , ups charged me , 22.27 gst , 37.55 ,brokerage fee
>and another 2.63 gst on the brok fee,s , needless to say i have learned a
>valuable lesson ,(expensive too).
> Does anyone in Canada know of a place to buy 6061 ?
>
>
>Regards
>
>Bill Stuart.
>
>ch701sp
>sn 75664
>just started the rudder ,
>in no rush ,planning on abt 5years to complete.
>
>
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|