Today's Message Index:
----------------------
1. 07:25 AM - Re: Re: 6061 in Canada (Dave & Darlene)
2. 07:25 AM - Re: GPS (louiscfi@comcast.net)
3. 07:49 AM - Re: GPS (Jack Russell)
4. 07:56 AM - Re: GPS (Ray Montagne)
5. 08:21 AM - Re: GPS (Rick)
6. 08:21 AM - Re: GPS (Don WALKER)
7. 09:04 AM - Re: Re: 6061 in Canada (Carlos Sa)
8. 09:29 AM - Re: Re: 6061 in Canada (Bill Cardell)
9. 09:56 AM - Re: GPS (Bob Black)
10. 04:22 PM - Re: GPS (Brandon Tucker)
11. 06:56 PM - 701SP Kit For Sale (Bohannon Larry)
12. 07:10 PM - Re: Re: 6061 in Canada (Dave & Darlene)
13. 07:12 PM - Re: Re: 6061 in Canada (Dave & Darlene)
14. 07:49 PM - List members (Cdngoose)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: 6061 in Canada |
--> Zenith-List message posted by: "Dave & Darlene" <dnimigon@telusplanet.net>
Hi Jarek
I looked into Integris out here in Calgary. They used to carry a few sizes
but now only carry .025 in 6061. Edmonton has the extruded angle. Minimum
order of $500. They have lots of 2024 as they supply the aircraft industry.
really expensive on the 2024. I also looked into buying from Yard Metals in
the US. Their cost is per pound. Will ship and have every size. Prices I got
were good I thought even with the exchange. I plan on placing an order as
soon as the holidays are over.
David Nimigon
601XL
Alberta
99% to go
----- Original Message -----
From: "Jarek M. Walter" <jarek.walter@sympatico.ca>
Subject: Zenith-List: Re: 6061 in Canada
> --> Zenith-List message posted by: "Jarek M. Walter"
> <jarek.walter@sympatico.ca>
>
> Has anyone bought from www.integrismetals.com? They seems to have
> branches
> across Canada.
> Regards, Jarek
>
>
>
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
0.50 MIME_BOUND_NEXTPART Spam tool pattern in MIME boundary
0.01 RCVD_DOUBLE_IP_LOOSE Received: by and from look like IP addresses
--> Zenith-List message posted by: louiscfi@comcast.net
Bob,
I planned on using one of these in my airplane until I played w/ it at sun
n fun. What a disappointment. The screen was very slow to reload. The movement
through all of the menus was not very intuitive. It was like I had to push
a million buttons just to go direct. You may disagree, and it may work well
for you, so maybe you should try one before you buy.
For about the same price you could buy a brand new color gps like the lowrance
2000c. It has a big 5" color screen, and will soon include a terrain database.
It is only $1000. Check out my website and click on the possible gps's
on the homepage. Keep in mind I have never used these gps's myself, but we are
nearing the time to test these gps's. So soon I will have personal experience
w/ these.
--
Louis
601xl, corvair pwr
j-41 capt
CFII SMEL
http://www.N601LV.com
Bob,
I planned on using one of these in my airplane until I played w/ it at sun n fun.
What a disappointment. The screen was very slow to reload. The movement through
all of the menus was not very intuitive. It was like I had to push a million
buttons just to go direct. You may disagree, and it may work well for you,
so maybe you should try one before you buy.
For about the same price you could buy a brand new color gps like the lowrance
2000c. It has a big 5" colorscreen, and will soon include a terrain database.
It is only $1000. Check out my website and click on the possible gps's on the
homepage. Keep in mind I have never used these gps's myself, but we are nearing
the time to test these gps's. So soon I will have personal experience w/ these.
--
Louis
601xl, corvair pwr
j-41 capt
CFII SMEL
http://www.N601LV.com
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> Zenith-List message posted by: Jack Russell <clojan@sbcglobal.net>
Bob: I am just about ready to cut the first hole in my panel. I just bought the
lowrance 2000c air map which will take up residence in the center of my panel.
What an inprovement over my old garmin89. The screen is color and huge! When
I first turned it on, it found itself in less than 1minute. I love the split
map feature.
I was a little worried about the depth of the unit on my panel but the way they
designed the case I will be able to build it into the panel and only about 3\4
inch will stick out. It will look like a panel mount. I will post pictures when
done. The only drawback is that it is battery hungry and they only last 2
hrs. Ok for me because I will hard wire 12v but could be a problem for a renter.
Jack in Clovis Ca
Bob Black <black@usa.sh> wrote:
--> Zenith-List message posted by: "Bob Black"
There's a newer model GPS for sale on ebay. The bids look pretty low.
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem
&item=4513914376
Has anyone used one of these?
Bob Black
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> Zenith-List message posted by: Ray Montagne <ac6qj@earthlink.net>
On 12/27/04 7:48 AM, "Jack Russell" <clojan@sbcglobal.net> wrote:
> There's a newer model GPS for sale on ebay. The bids look pretty low.
Folks,
Seems to me that all of the ebay announcements are beyond the intended scope
of this list. I hope that announcements of tygo tubing, pitot heads, brake
calipers, etc. are not forthcoming...
Ray Montagne
Cupertino, CA
601XL
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> Zenith-List message posted by: Rick <n701rr@yahoo.com>
I'm about ready to put my Garmin 196 on Ebay and go with the Lowrance Airmap 2000c
as well.
Thoughts??
DO NOTARCHIVE.
Rick
Orlando, FL
http://www.geocities.com/n701rr/index.html
---------------------------------
Send holiday email and support a worthy cause. Do good.
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> Zenith-List message posted by: "Don WALKER" <d3dw@msn.com>
Thanks for monitoring the list Ray. You are probably right, though I like to
know about good deals. By the way, in the future would you mind writng DO
NOT ARCHIVE on your criticisms. They are probably less worthy of storage
space than the GPS messages in my opinion. Don Walker HDS
>From: Ray Montagne <ac6qj@earthlink.net>
>Reply-To: zenith-list@matronics.com
>To: Zenith List <zenith-list@matronics.com>
>Subject: Re: Zenith-List: GPS
>Date: Mon, 27 Dec 2004 07:55:51 -0800
>
>--> Zenith-List message posted by: Ray Montagne <ac6qj@earthlink.net>
>
>On 12/27/04 7:48 AM, "Jack Russell" <clojan@sbcglobal.net> wrote:
>
> > There's a newer model GPS for sale on ebay. The bids look pretty low.
>
>Folks,
>
>Seems to me that all of the ebay announcements are beyond the intended
>scope
>of this list. I hope that announcements of tygo tubing, pitot heads, brake
>calipers, etc. are not forthcoming...
>
>Ray Montagne
>Cupertino, CA
>601XL
>
>
Message 7
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: 6061 in Canada |
--> Zenith-List message posted by: Carlos Sa <carlosfsa@yahoo.com>
David, a reminder: UPS fees (brokerage and / or whatever else) are a rip-off.
You might want to give them (or whatever transportation co. you use) a call before
ordering.
Your supplier in the US is not necessarily aware of these fees.
Carlos
Montreal, Canada
do not archive
--- Dave & Darlene <dnimigon@telusplanet.net> wrote:
> --> Zenith-List message posted by: "Dave & Darlene" <dnimigon@telusplanet.net>
>
> Hi Jarek
> I looked into Integris out here in Calgary. They used to carry a few sizes
> but now only carry .025 in 6061. Edmonton has the extruded angle. Minimum
> order of $500. They have lots of 2024 as they supply the aircraft industry.
> really expensive on the 2024. I also looked into buying from Yard Metals in
> the US. Their cost is per pound. Will ship and have every size. Prices I got
> were good I thought even with the exchange. I plan on placing an order as
> soon as the holidays are over.
>
> David Nimigon
> 601XL
> Alberta
> 99% to go
Message 8
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: 6061 in Canada |
--> Zenith-List message posted by: Bill Cardell <bill@flyinmiata.com>
Don't know if this info might be useful, but if you do use UPS going to
Canada, it's often more cost effective to use expedited or express, rather
than ground service. Expedited and express both have the brokerage fees
built in, as opposed to UPS nailing you extra when you use ground. You'll
still pay the actual taxes, but you'll know that there won't be additional
fees for brokerage. Just a thought.
Do not archive.
-----Original Message-----
From: Carlos Sa [mailto:carlosfsa@yahoo.com]
Subject: Re: Zenith-List: Re: 6061 in Canada
--> Zenith-List message posted by: Carlos Sa <carlosfsa@yahoo.com>
David, a reminder: UPS fees (brokerage and / or whatever else) are a
rip-off. You might want to give them (or whatever transportation co. you
use) a call before ordering.
Your supplier in the US is not necessarily aware of these fees.
Carlos
Montreal, Canada
do not archive
Message 9
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> Zenith-List message posted by: "Bob Black" <black@usa.sh>
Thanks Jack,
I was considering a bid on this, but I hadn't considered the Lawrence. I
did get a couple off-list comments about promoting products. It seems those
folks didn't get the point that I was asking a question. So far, you are
the only person who got the point and has been helpful. Thanks again.
Do not archive.
Bob
-----Original Message-----
From: owner-zenith-list-server@matronics.com
[mailto:owner-zenith-list-server@matronics.com] On Behalf Of Jack Russell
Subject: Re: Zenith-List: GPS
--> Zenith-List message posted by: Jack Russell <clojan@sbcglobal.net>
Bob: I am just about ready to cut the first hole in my panel. I just bought
the lowrance 2000c air map which will take up residence in the center of my
panel. What an inprovement over my old garmin89. The screen is color and
huge! When I first turned it on, it found itself in less than 1minute. I
love the split map feature.
I was a little worried about the depth of the unit on my panel but the way
they designed the case I will be able to build it into the panel and only
about 3\4 inch will stick out. It will look like a panel mount. I will post
pictures when done. The only drawback is that it is battery hungry and they
only last 2 hrs. Ok for me because I will hard wire 12v but could be a
problem for a renter. Jack in Clovis Ca
Bob Black <black@usa.sh> wrote:
--> Zenith-List message posted by: "Bob Black"
There's a newer model GPS for sale on ebay. The bids look pretty low.
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem
&item=4513914376
Has anyone used one of these?
Bob Black
Message 10
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> Zenith-List message posted by: Brandon Tucker <btucke73@yahoo.com>
Gents,
I bought the Lowrance airmap 1000 a few months
ago, and I like it a lot. It is the same unit as the
2000c, but B&W. -Very easy to use, and I got it on
sale for $650. I plan to panel mount it next to the
Stratomaster Ultra. The support software leaves a
little to be desired, but works fine for simple flight
planning.
Respectfully,
Brandon
HDS
Dissasembling the fuse to
deburr and primer
DO NOT ARCHIVE
__________________________________
http://info.mail.yahoo.com/mail_250
Message 11
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | 701SP Kit For Sale |
0.50 MIME_BOUND_NEXTPART Spam tool pattern in MIME boundary
--> Zenith-List message posted by: "Bohannon Larry" <bohannon54@earthlink.net>
I have decided to sell my almost completed 701SP kit. I bought the kit on Jan.31,
2003 at the factory workshop. I have about 1000 hrs. work in it already and
because of other committments that have come up lately won't be able to dedicate
the necessary time needed to finish it. I have really enjoyed working on
it have proceed at a slow and carefull pace and I believe, good workmanship.
So it's in my garage/workshop and the wife is wanting the garage back for our
cars. All of the major parts are done. The tailfeathers with electric trim, both
wings with strobe/nav, flaperons, rear fuselage, cabin area and firewall are
all completed. Left to finish is joining the cabin to the rear fuselage and
putting in the main landing gear and also the slats need to be built. I went
ahead and bought the motor mount for 912s to use while building the firewall.
I also have already installed a BRS chute in the baggage compartment. I will consider
delivering up to about 800 miles from Atlanta
, Georgia. I paid $14,091.05 for the complete Kit, $493.00 for the motor mount,
$3,361.43 for the BRS chute, and $998.17 for misc. tools,rivets,access plates,
wiring,extra L angles, etc.etc. Zenith air riveter and tools included along
with builders log with photos during construction. Also included are bound copies
of Zenair News from 1985-Present. I have $18,943.65 ++ in the project.
Make an offer. I plan on putting an ad in my local EAA 690 Chapter newsletter
and also in Barnstormers and maybe E-Bay later. Can anybody suggest any other
places I could list it for sale?
Regards,
Larry Bohannon
Winder, Georgia
Bohannon Larry
bohannon54@earthlink.net
Message 12
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: 6061 in Canada |
--> Zenith-List message posted by: "Dave & Darlene" <dnimigon@telusplanet.net>
Hi Carlos
I did check into shipping from a company in Edmonton. Told them where it was
and said it was probably a 4x12 pallet. They told me it would be $160USD to
bring it up here. Not sure about all the other junk, brokerage fees,duty,
etc. How can a guy find out all of this. Maybe someone on the list has done
this and can let us know. I'd maybe like to find out before I place the
order and then find out it will cost a fortune to get it here.
Dave
Alberta
----- Original Message -----
From: "Carlos Sa" <carlosfsa@yahoo.com>
Subject: Re: Zenith-List: Re: 6061 in Canada
> --> Zenith-List message posted by: Carlos Sa <carlosfsa@yahoo.com>
>
> David, a reminder: UPS fees (brokerage and / or whatever else) are a
> rip-off.
> You might want to give them (or whatever transportation co. you use) a
> call before ordering.
> Your supplier in the US is not necessarily aware of these fees.
>
> Carlos
> Montreal, Canada
> do not archive
>
>
> --- Dave & Darlene <dnimigon@telusplanet.net> wrote:
>> --> Zenith-List message posted by: "Dave & Darlene"
>> <dnimigon@telusplanet.net>
>>
>> Hi Jarek
>> I looked into Integris out here in Calgary. They used to carry a few
>> sizes
>> but now only carry .025 in 6061. Edmonton has the extruded angle. Minimum
>> order of $500. They have lots of 2024 as they supply the aircraft
>> industry.
>> really expensive on the 2024. I also looked into buying from Yard Metals
>> in
>> the US. Their cost is per pound. Will ship and have every size. Prices I
>> got
>> were good I thought even with the exchange. I plan on placing an order as
>> soon as the holidays are over.
>>
>> David Nimigon
>> 601XL
>> Alberta
>> 99% to go
>
>
>
Message 13
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: 6061 in Canada |
--> Zenith-List message posted by: "Dave & Darlene" <dnimigon@telusplanet.net>
Another thought would be to get one of the US builders that are close to the
Alberta border to have the shipment sent to his place. I would then take a
drive to get it. We could re-wrap it or something and then bring it across
as used metal. Not sure if this would work or not.
Dave
Alberta
DO NOT Archive
----- Original Message -----
From: "Bill Cardell" <bill@flyinmiata.com>
Subject: RE: Zenith-List: Re: 6061 in Canada
> --> Zenith-List message posted by: Bill Cardell <bill@flyinmiata.com>
>
> Don't know if this info might be useful, but if you do use UPS going to
> Canada, it's often more cost effective to use expedited or express, rather
> than ground service. Expedited and express both have the brokerage fees
> built in, as opposed to UPS nailing you extra when you use ground. You'll
> still pay the actual taxes, but you'll know that there won't be additional
> fees for brokerage. Just a thought.
>
> Do not archive.
>
> -----Original Message-----
> From: Carlos Sa [mailto:carlosfsa@yahoo.com]
> To: zenith-list@matronics.com
> Subject: Re: Zenith-List: Re: 6061 in Canada
>
>
> --> Zenith-List message posted by: Carlos Sa <carlosfsa@yahoo.com>
>
> David, a reminder: UPS fees (brokerage and / or whatever else) are a
> rip-off. You might want to give them (or whatever transportation co. you
> use) a call before ordering.
> Your supplier in the US is not necessarily aware of these fees.
>
> Carlos
> Montreal, Canada
> do not archive
>
>
>
Message 14
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> Zenith-List message posted by: "Cdngoose" <601xl@sympatico.ca>
I would like to ask if a 601 kit builder would mind spending a bit of
time and doing an Inventory of there hardware kit that they get with the
plane and sending me a copy of the inventory list so that I may add it
to the www.ch601.org website to help all of the plans builders. I
already have a materials and cutting list. It is almost an impossible
task to make up a hardware list by going through the plans alone.
For you 701 builders does anyone have a cutting list for materials?
Thanks
Mark Townsend
Alma, Ontario
Zodiac 601XL EJ 2.2L
Osprey 2 serial # 751
www.ch601.org
www.Osprey2.com
do not archive
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|