Today's Message Index:
----------------------
1. 05:45 AM - Dremel tool (Greg Marlow)
2. 06:43 AM - Re: Dremel tool (Jim Hoak)
3. 07:11 AM - Re: Location for the NACA cockpit vent? (Daniel Vandenberg)
4. 07:45 AM - Re: Dremel tool (george may)
5. 07:45 AM - Re: Dremel tool (Paul Mulwitz)
6. 08:07 AM - Re: Gas-Welding or Arc-Welding Question (Murray Randall)
7. 01:28 PM - [ Tim Shankland ] : New Email List Photo Share Available! (Email List Photo Shares)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> Zenith-List message posted by: "Greg Marlow" <gregmarlow@charter.net>
Hello!
First time posting here. I'm just getting started with my XL, actually
attending the rudder workshop next month. I'm getting organized, work
shop, bench, some basic tools that I didn't have lying around already,
etc., and had a simple question - I was going to get a Dremel tool
anyway, and I was wondering if there is any real advantage to the
variable speed vs. the two speed models?
Thanks in advance and thanks for all the invaluable advice you guys have
already provided.
Greg Marlow
do not archive
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> Zenith-List message posted by: "Jim Hoak" <planejim@bellsouth.net>
Greg,
Get the vatiable speed, it's the best in the long run.
Jim Hoak
do not archive
----- Original Message -----
From: "Greg Marlow" <gregmarlow@charter.net>
Sent: Sunday, April 16, 2006 8:36 AM
Subject: Zenith-List: Dremel tool
> --> Zenith-List message posted by: "Greg Marlow" <gregmarlow@charter.net>
>
> Hello!
>
> First time posting here. I'm just getting started with my XL, actually
> attending the rudder workshop next month. I'm getting organized, work
> shop, bench, some basic tools that I didn't have lying around already,
> etc., and had a simple question - I was going to get a Dremel tool
> anyway, and I was wondering if there is any real advantage to the
> variable speed vs. the two speed models?
>
> Thanks in advance and thanks for all the invaluable advice you guys have
> already provided.
>
> Greg Marlow
>
> do not archive
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Location for the NACA cockpit vent? |
--> Zenith-List message posted by: "Daniel Vandenberg" <djvdb63@yahoo.com>
[quote="nfivesl(at)yahoo.com"]I put mine here and so far it hasn't run into anything
and allows for installation of my BRS harness:
http://www.cooknwithgas.com/4_1_06_Kitplanes.JPG
Scott...
I think we've caught you daydreaming about the RV-9A in the latest Kitplanes
[Wink]
Dan
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=28711#28711
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> Zenith-List message posted by: "george may" <gfmjr_20@hotmail.com>
Greg-
Get the variable speed. It will give you more options when trying to cut
metal and/or
fiberglass
George May
601XL 912s Engine first startup schedule for tomorrow
do no archive
>
>
On the road to retirement? Check out MSN Life Events for advice on how to
get there! http://lifeevents.msn.com/category.aspx?cid=Retirement
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
--> Zenith-List message posted by: Paul Mulwitz <p.mulwitz@worldnet.att.net>
Hi Greg,
Welcome aboard.
I recently got one of the new lithium battery powered ones. It is
variable speed and goes faster than any of the corded ones. I find
it wonderful to use.
Paul
XL wings
>First time posting here. I'm just getting started with my XL, actually
>attending the rudder workshop next month. I'm getting organized, work
>shop, bench, some basic tools that I didn't have lying around already,
>etc., and had a simple question - I was going to get a Dremel tool
>anyway, and I was wondering if there is any real advantage to the
>variable speed vs. the two speed models?
>
>Thanks in advance and thanks for all the invaluable advice you guys have
>already provided.
>
>Greg Marlow
>
>
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Gas-Welding or Arc-Welding Question |
--> Zenith-List message posted by: "Murray Randall" <aeroads@comcast.net>
A friend of mine, a Pitts builder, got a Lincon Sq Wave 175 on Ebay and there were
two listed then But none now I bought a 175 new years ago and it does
well in the hands of a hack Check Ebay Murray
Message 7
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | [ Tim Shankland ] : New Email List Photo Share Available! |
--> Zenith-List message posted by: Email List Photo Shares <pictures@matronics.com>
A new Email List Photo Share is available:
Poster: Tim Shankland <tshank@core.com>
Lists: Zenith-List
Subject: Tach filter
http://www.matronics.com/photoshare/tshank@core.com.04.16.2006/index.html
o Main Photo Share Index
http://www.matronics.com/photoshare
o Submitting a Photo Share
If you wish to submit a Photo Share of your own, please include the
following information along with your email message and files:
1) Email List or Lists that they are related to:
2) Your Full Name:
3) Your Email Address:
4) One line Subject description:
5) Multi-line, multi-paragraph description of topic:
6) One-line Description of each photo or file:
Email the information above and your files and photos to:
pictures@matronics.com
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|