---------------------------------------------------------- Zenith-List Digest Archive --- Total Messages Posted Sun 03/08/09: 13 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 09:34 AM - ELT Antenna (Bill Naumuk) 2. 11:06 AM - Watch out (Bill Naumuk) 3. 12:04 PM - Re: ELT Antenna (LarryMcFarland) 4. 12:33 PM - Re: ELT Antenna (Bill Naumuk) 5. 01:21 PM - D-100 (Bill Naumuk) 6. 02:01 PM - Re: D-100 (Sabrina) 7. 02:19 PM - Re: Re: D-100 (Bill Naumuk) 8. 02:34 PM - Re: Re: D-100 (jaybannist@cs.com) 9. 02:53 PM - Re: Re: D-100 (Bill Naumuk) 10. 04:22 PM - Re: Re: Lightning holes flange dies & sizes (William Dominguez) 11. 06:06 PM - Fw: got enough goverment in your life? (Keith Ashcraft) 12. 08:56 PM - Re: D-100 (Sabrina) 13. 09:53 PM - Re: Re: Lightning holes flange dies & sizes (Randy L. Thwing) ________________________________ Message 1 _____________________________________ Time: 09:34:58 AM PST US From: "Bill Naumuk" Subject: Zenith-List: ELT Antenna All- Do you have to use the same brand antenna as your ELT, or are they interchangable? Do not archive Bill Naumuk Townville, Pa. HDS 601MG/Corvair 95% ________________________________ Message 2 _____________________________________ Time: 11:06:45 AM PST US From: "Bill Naumuk" Subject: Zenith-List: Watch out All- Found my ELT antenna in the bottom of my burn barrel. Spring cleaning can be costly. Do not archive Bill Naumuk Townville, Pa. HDS 601MG/Corvair 95% ________________________________ Message 3 _____________________________________ Time: 12:04:50 PM PST US From: LarryMcFarland Subject: Re: Zenith-List: ELT Antenna My ELT and Com antennas look very much alike. They work within the same band width so they'd probably be the same. Larry McFarland 601HDS at www.macsmachine.com do not archive Bill Naumuk wrote: > All- > Do you have to use the same brand antenna as your ELT, or are they > interchangable? > Do not archive > Bill Naumuk > Townville, Pa. > HDS 601MG/Corvair 95% > * > > > * ________________________________ Message 4 _____________________________________ Time: 12:33:53 PM PST US From: "Bill Naumuk" Subject: Re: Zenith-List: ELT Antenna Larry- Found out I burned my original antenna spring cleaning. Yes, I'm an idiot. Bill ----- Original Message ----- From: "LarryMcFarland" Sent: Sunday, March 08, 2009 3:03 PM Subject: Re: Zenith-List: ELT Antenna > > My ELT and Com antennas look very much alike. They work within the same > band width > so they'd probably be the same. > > Larry McFarland 601HDS at www.macsmachine.com > do not archive > > Bill Naumuk wrote: >> All- >> Do you have to use the same brand antenna as your ELT, or are they >> interchangable? >> Do not archive >> Bill Naumuk >> Townville, Pa. >> HDS 601MG/Corvair 95% >> * >> >> >> * > > > ________________________________ Message 5 _____________________________________ Time: 01:21:11 PM PST US From: "Bill Naumuk" Subject: Zenith-List: D-100 All- Has anyone successfully had-wired a D-100? If so, please contact me off list. Do not archieve Bill Naumuk Townville, Pa. HDS 601MG/Corvair 95% ________________________________ Message 6 _____________________________________ Time: 02:01:50 PM PST US Subject: Zenith-List: Re: D-100 From: "Sabrina" The Stein cables supplied with some D-100 and D-180s have had wire pairs reversed. A continuity check of each pin is a good idea before installing. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=233764#233764 ________________________________ Message 7 _____________________________________ Time: 02:19:13 PM PST US From: "Bill Naumuk" Subject: Re: Zenith-List: Re: D-100 Sabrina- I'm trying to wire the harness from scratch using B+C components. I'm unsure of the schematic. I could really use a reverse-engineered diagram of the Stein cable. Bill do not archive ----- Original Message ----- From: "Sabrina" Sent: Sunday, March 08, 2009 5:00 PM Subject: Zenith-List: Re: D-100 > > The Stein cables supplied with some D-100 and D-180s have had wire pairs > reversed. A continuity check of each pin is a good idea before > installing. > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=233764#233764 > > > ________________________________ Message 8 _____________________________________ Time: 02:34:21 PM PST US Subject: Re: Zenith-List: Re: D-100 From: jaybannist@cs.com Bill, Do you have the Dynon Installation Guide?? The diagrams for both cables and connectors are all laid out there. Jay -----Original Message----- From: Bill Naumuk Sent: Sun, 8 Mar 2009 4:18 pm Subject: Re: Zenith-List: Re: D-100 ? Sabrina-? ? I'm trying to wire the harness from scratch using B+C components. I'm unsure of the schematic. I could really use a reverse-engineered diagram of the Stein cable.? ? ? Bill? ? do not archive? ----- Original Message ----- From: "Sabrina" ? Sent: Sunday, March 08, 2009 5:00 PM? Subject: Zenith-List: Re: D-100? ? >? > The Stein cables supplied with some D-100 and D-180s have had wire pairs > reversed. A continuity check of each pin is a good idea before > installing.? >? >? >? >? > Read this topic online here:? >? > http://forums.matronics.com/viewtopic.php?p=233764#233764? >? >? >? >? >? >? >? >? >? > ? ? ? ________________________________________________________________________ Email message sent from CompuServe - visit us today at http://www.cs.com ________________________________ Message 9 _____________________________________ Time: 02:53:14 PM PST US From: "Bill Naumuk" Subject: Re: Zenith-List: Re: D-100 Jay- Yes, but they're written in Greek. I just found out I could by a pre-made cable for what I paid for the components. Live, get kicked in the butt, and learn. Of course, if you can read Greek, I'll send you the appropriate scans. I'm lost. Bill do not archive ----- Original Message ----- From: jaybannist@cs.com To: zenith-list@matronics.com Sent: Sunday, March 08, 2009 5:33 PM Subject: Re: Zenith-List: Re: D-100 Bill, Do you have the Dynon Installation Guide? The diagrams for both cables and connectors are all laid out there. Jay -----Original Message----- From: Bill Naumuk To: zenith-list@matronics.com Sent: Sun, 8 Mar 2009 4:18 pm Subject: Re: Zenith-List: Re: D-100 Sabrina- I'm trying to wire the harness from scratch using B+C components. I'm unsure of the schematic. I could really use a reverse-engineered diagram of the Stein cable. Bill do not archive ----- Original Message ----- From: "Sabrina" To: Sent: Sunday, March 08, 2009 5:00 PM Subject: Zenith-List: Re: D-100 > > The Stein cables supplied with some D-100 and D-180s have had wire pairs > reversed. A continuity check of each pin is a good idea before > installing. > > > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=233764#233764 > > > > > > > > > > ------------------------------------------------------------------------- ----- Email message sent from CompuServe - visit us today at http://www.cs.com ________________________________ Message 10 ____________________________________ Time: 04:22:06 PM PST US From: William Dominguez Subject: Re: Zenith-List: Re: Lightning holes flange dies & sizes I made my dies out of plywood here's how they came out: http://picasaweb.google.com/billdomg/Wings#5157577544559844594 http://picasaweb.google.com/billdomg/Wings#5157577557444746498 Then I used a slotted stick to straighten the rib web, you might still have to do this even if you use steel dies: http://picasaweb.google.com/billdomg/Wings#5157577600394419522 It was faster than doing it with the stick from the beginning- and the wo oden dies are easy to make. Here are the instruction on how to make wooden flanging dies. http://www.ch601.org/tools/Flanging%20Dies%20Construction2.pdf William Dominguez Zodiac 601XL Plans Miami Florida http://www.geocities.com/bill_dom --- On Sat, 3/7/09, Lee Steensland wrote: From: Lee Steensland Subject: Zenith-List: Re: Lightning holes flange dies & sizes At one point I posted about borrowing a set from someone. I planned to make a set of dies or have a set made, but the cheapest price I was quoted was like $500 or some such. I decided to just use a slotted st ick with prices like that. If I could borrow a set that would be spectacular. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=233649#233649 le, List Admin. ________________________________ Message 11 ____________________________________ Time: 06:06:35 PM PST US From: Keith Ashcraft Subject: Zenith-List: Fw: got enough goverment in your life? All, I received this from another yahoo group. It is just something that us fliers should be aware of. I have forwarded it to the 701 Yahoo group, and thought that it might be sent to the Matronics list also. (hopefully the link still works) Keith CH701 - scratch N 38.9940 W 105.1305 Alt. 9,100' ******************************************** http://groups. google.com/ group/rec. aviation. homebuilt/ browse_thread/ thread/6a16111ba 0f17617# ________________________________ Message 12 ____________________________________ Time: 08:56:16 PM PST US Subject: Zenith-List: Re: D-100 From: "Sabrina" Bill, I wish had gone your route. I just looked over the online manual for the D100, it seems pretty straight forward if you stick to the PIN9 is this, PIN10 is this etc., as described in the various tables. So, use the tables and the numbers on the connectors. The schematic is there as a back up and really not needed except to point out which wires are shielded and which are not. http://www.dynonavionics.com/downloads/Install_Guides/EFIS-D100%20Installation%20Guide.pdf Read this topic online here: http://forums.matronics.com/viewtopic.php?p=233827#233827 ________________________________ Message 13 ____________________________________ Time: 09:53:09 PM PST US From: "Randy L. Thwing" Subject: Re: Zenith-List: Re: Lightning holes flange dies & sizes Do not archive Hello Lee: I have a set of steel Zenith dimensioned dies that I am happy to loan to other Builders. Several Listers have used these with positive results. They are currently on the way to another Builder who estimated that he would have them for s short time. What is your requirement? How soon would you need them, and where are you located? Regards, Randy, Las Vegas ----- Original Message ----- From: "Lee Steensland" Sent: Saturday, March 07, 2009 9:35 PM Subject: Zenith-List: Re: Lightning holes flange dies & sizes > > At one point I posted about borrowing a set from someone. > > I planned to make a set of dies or have a set made, but the cheapest price > I was quoted was like $500 or some such. I decided to just use a slotted > stick with prices like that. > > If I could borrow a set that would be spectacular. ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message zenith-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Zenith-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/zenith-list Browse Digests http://www.matronics.com/digest/zenith-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.