Today's Message Index:
----------------------
1. 05:25 AM - Prop (wade jones)
2. 05:40 AM - Re: Prop (Sabrina)
3. 05:57 AM - Re: Re: Prop (wade jones)
4. 06:24 AM - Re: Prop (Juan Vega)
5. 02:08 PM - Re: Prop (wade jones)
6. 11:09 PM - Corvair (messydeer)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Hello group ,I plan to order my propeller today for my 601XL .I will be
using the Franklin 125hp engine .I have requested the prop builder to
use 68"X60" for the prop .Do you think this is a good number .
Wade Jones South Texas
601XL Franklin 0-235
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
I had my 2 blade 69 klip tip cut down to 67. With a bungee failure and nose tire
flat, 68 or 69 did not give enough ground clearance on a 2 blade prop.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=237499#237499
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Thanks Sabrina thats the kind of input I am looking for .
Wade Jones South Texas
601XL Franklin 0-235
----- Original Message -----
From: "Sabrina" <chicago2paris@msn.com>
Sent: Friday, April 03, 2009 7:39 AM
Subject: Zenith-List: Re: Prop
>
> I had my 2 blade 69 klip tip cut down to 67. With a bungee failure and
> nose tire flat, 68 or 69 did not give enough ground clearance on a 2 blade
> prop.
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=237499#237499
>
>
>
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
measure from the prop hub straight down to the ground and deduct 18 inches or so.
you will probably get around 64"
Juan
-----Original Message-----
>From: wade jones <wjones@brazoriainet.com>
>Sent: Apr 3, 2009 8:23 AM
>To: zenith-list@matronics.com
>Subject: Zenith-List: Prop
>
>Hello group ,I plan to order my propeller today for my 601XL .I will be using
the Franklin 125hp engine .I have requested the prop builder to use 68"X60" for
the prop .Do you think this is a good number .
>Wade Jones South Texas
>601XL Franklin 0-235
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Thanks Juan ,however I don't quite understand .
Wade Jones South Texas
601XL Franklin 0-235
----- Original Message -----
From: "Juan Vega" <amyvega2005@earthlink.net>
Sent: Friday, April 03, 2009 8:23 AM
Subject: Re: Zenith-List: Prop
>
> measure from the prop hub straight down to the ground and deduct 18 inches
> or so. you will probably get around 64"
>
> Juan
>
> -----Original Message-----
>>From: wade jones <wjones@brazoriainet.com>
>>Sent: Apr 3, 2009 8:23 AM
>>To: zenith-list@matronics.com
>>Subject: Zenith-List: Prop
>>
>>Hello group ,I plan to order my propeller today for my 601XL .I will be
>>using the Franklin 125hp engine .I have requested the prop builder to use
>>68"X60" for the prop .Do you think this is a good number .
>>Wade Jones South Texas
>>601XL Franklin 0-235
>
>
>
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Hello!
I'm considering powering my bird with a Corvair engine. I have limited experience
rebuilding engines (replaced a Subie head gasket once) and would have an experienced
Corvair builder do this for me. I would not provide the cadaver or any
organs.
To save money, I would be comfortable in assembling some of the engine myself.
Look forward to hearing your experiences, suggestions, and references.
Cheers,
Dan
--------
Dan
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=237624#237624
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|