---------------------------------------------------------- Zenith-List Digest Archive --- Total Messages Posted Sat 08/22/09: 5 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 01:52 AM - Re: Rotax 912 Warning lights (Martin Pohl) 2. 03:22 AM - Re: First Start of an O-200 (Peter W Johnson) 3. 11:19 AM - Corvair flywheels () 4. 03:25 PM - New Forum (George Race) 5. 06:57 PM - Re: Rotax 912 Warning lights (marcflyer) ________________________________ Message 1 _____________________________________ Time: 01:52:03 AM PST US Subject: Zenith-List: Re: Rotax 912 Warning lights From: "Martin Pohl" I will install an oil pressure and a fuel pressure warning light. Oil pressure sensor VDO: http://www.egauges.com/vdo_indS.asp?Sender=150PSI_10Bar&PN=360-025 Cheers Martin -------- Martin Pohl Zodiac XL QBK 8645 Jona, Switzerland http://www.pohltec.ch/ZodiacXL/Main.html Read this topic online here: http://forums.matronics.com/viewtopic.php?p=259062#259062 ________________________________ Message 2 _____________________________________ Time: 03:22:03 AM PST US From: "Peter W Johnson" Subject: Zenith-List: Re: First Start of an O-200 Hi Guys, I managed a milestone today in starting the engine for the first time. I made up a pressure oiler and pressurised the system through the oil pressure gauge output fitting. I also primed the oil pump through the filter housing. A couple of turns and she was away. Pressure was up in seconds and managed to get to 40 psi at around 1300rpm. Not quite as smooth as the Corvair but all is good to go. Cheers Peter Wonthaggi Australia http://zodiac.cpc-world.com -----Original Message----- From: owner-zenith-list-server@matronics.com [mailto:owner-zenith-list-server@matronics.com] On Behalf Of Sabrina Sent: Tuesday, 18 August 2009 3:56 PM Subject: Zenith-List: Re: First Start of an O-200 You know guys, spinning the engine with the starter is still a dry crank which the TCM manual is trying to avoid. First off, everything inside the engine should have been lubricated with 100W mineral oil before/during assembly. Second, there are the (PN 532432) plugs at the front of the engine, the ports where the oil cooler pad (PN 35033) mounts, the original oil screen housing (PN 35020), the oil pressure relief valve (PN 21113) as well as the oil pressure outlet. Each of these can be used to prime and/or check the effectiveness of your prime. If you are ambitious, you can remove the valve covers as well. I added a quart of Royco flight ready preservative oil before the first start. The oil flow charts (Figure 38 of the TCM overhaul manual) for the O-200A showing pressure oil, scavenge oil-suction and scavenge oil-drain are helpful in understanding where the oil is going that you are pumping in with a rubber tipped oil can. Looking at the charts, it is clear that removing the oil cooler pad (or STC'd oil filter) allows you to prime the oil pump with the top hole and pressurize the oil passages, key to the first start up, with the lower hole. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=258377#258377 ________________________________ Message 3 _____________________________________ Time: 11:19:56 AM PST US From: Subject: Zenith-List: Corvair flywheels After driving my local NAPA guy nuts trying to find the flywheel WW recommends (Pioneer Products, FRA 235), I found a source here in Kansas City, at a transmission shop. Price was $35.00. I didn't ask him to go back and look, but he thinks he has about 6 of them on hand. I grabbed one, and had it drilled to fit, at a cost of $20. Now, on to finding a Soob starter! Paul R. ________________________________ Message 4 _____________________________________ Time: 03:25:02 PM PST US From: "George Race" Subject: Zenith-List: New Forum WANTED - QUESTIONS and ANSWERS Want to take you discussions to a different level? Check out my new style Forum located at: www.mykitairplane.com/forum George Do Not Archive ________________________________ Message 5 _____________________________________ Time: 06:57:21 PM PST US Subject: Zenith-List: Re: Rotax 912 Warning lights From: "marcflyer" Thanks for the help Martin I will order the part. I hope the limits are within Rotax range. Any suggestion for the Eng Temp. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=259146#259146 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message zenith-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Zenith-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/zenith-list Browse Digests http://www.matronics.com/digest/zenith-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.