Today's Message Index:
----------------------
 
     1. 01:46 AM - Re: Choke cable and Rotax 912 (Martin Pohl)
     2. 07:29 AM - Re: Choke cable and Rotax 912 (John Goodings)
     3. 11:39 PM - 601XL Cowling (Peter W Johnson)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
01:46:43 AM PST US
Subject: 
Re: Choke cable and Rotax 912
From: 
"Martin Pohl" <mpohl@pohltec.ch>
      
      
      George and Leo
      
      Thank you for your input. I will keep the system as is and just lubricate it a
      little bit with graphite.
      
      Cheers Martin
      
      --------
      Martin Pohl
      Zodiac XL QBK
      8645 Jona, Switzerland
      http://www.pohltec.ch/ZodiacXL/Main.html
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=260160#260160
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
07:29:06 AM PST US
From: 
John Goodings <goodings@yorku.ca>
Subject: 
Re: Choke cable and Rotax 912
      
      
      Six years ago when I was installing our Rotax 912S I was warned by an 
      experienced builder that the choke cable is notoriously hard to pull. 
      True!  I was also told not to worry about it - it will work fine.  Also 
      true!  A couple of times a year, we shoot Rust Check (it is a very thin 
      oil in a spray can, sold at Canadian Tire in Canada, but there will be 
      counterparts everywhere) into each end of the cable sheath.  It seems to 
      suck its way in along the cable by capillary action.  The only problem we 
      once had was that the choke did not fully release when we pushed it in. 
      Another application of Rust Check took care of the problem.
      
      John Goodings, C-FGPJ, CH601HD with R912S, Carp/Ottawa/Toronto.
      
      

Message 3


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
11:39:11 PM PST US
From: 
"Peter W Johnson" <vk3eka@bigpond.net.au>
Subject: 
601XL Cowling
      
      Hi Guys,
      
      
      I received my camlocs for the cowling from ASSC the other day.
      
      
      Attached is a photo. The photo shows:-
      
      
      40S5-3S SS CAMLOC STUD    
      
      4002-NS CAMLOC GROMMET            
      214-16ND CAMLOC 4002 Receptacle 
      
      
      How do I get the stud into the grommet. Do I have to remove the pin? If so,
      how?
      
      
      Cheers
      
      
      Peter
      
      Wonthaggi Australia
      
       <http://zodiac.cpc-world.com/> http://zodiac.cpc-world.com
      
      








Other Matronics Email List Services




Post A New Message
  
zenith-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/Zenith-List.htm
Web Forum Interface To Lists
  
http://forums.matronics.com
Matronics List Wiki
  
http://wiki.matronics.com
7-Day List Browse
  
http://www.matronics.com/browse/zenith-list
Browse Zenith-List Digests
  
http://www.matronics.com/digest/zenith-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --