Today's Message Index:
----------------------
1. 05:47 AM - Corvair Crank Prep (Bill Pagan)
2. 09:36 AM - Re: UK 601XL Mandatory Modifications & Tests Reports (vayuwings)
3. 10:05 AM - Re: UK 601XL Mandatory Modifications & Tests Reports (Sabrina)
4. 02:47 PM - Re: Corvair Crank Prep ()
5. 10:41 PM - Re: Signed off to Solo the Sabrina Mark 1 !!! (Ron Lendon)
6. 11:05 PM - Re: Corvair Crank Prep (Ron Lendon)
7. 11:07 PM - Re: Report no. 2 from Sun n Fun - The Heintz clan reactions to. (jimysymonds)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Corvair Crank Prep |
Hey All,
-
I believe there is a shop in Michigan (I think) that does corvair crank pre
p including nitriding but I can't seem to find it in WW's manual or in the
archives.
-
Anybody know this place and have info on them?
Bill Pagan
=0A=0A=0A
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: UK 601XL Mandatory Modifications & Tests Reports |
Thanks for posting the info, Clive
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=261240#261240
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: UK 601XL Mandatory Modifications & Tests Reports |
If anyone would like 3 sets of 6W2-2 (3L + 3R) .032 aileron ribs (not .025) they
are free to the first person who sends me a pre-paid UPS shipping label...
produced by Zenith in Mexico...
I have a bad feeling about these LAA mods, so use them at your own risk...
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=261252#261252
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Corvair Crank Prep |
Bill, several months ago there was an item from somebody around Chicago;
you might find it in the archives from around late April or early May.
I sent mine to Nitron.
Paul R
----- Original Message -----
From: Bill Pagan<mailto:pdn8r@yahoo.com>
To: Zenith List<mailto:zenith-list@matronics.com>
Sent: Thursday, September 03, 2009 7:29 AM
Subject: Zenith-List: Corvair Crank Prep
Hey All,
I believe there is a shop in Michigan (I think) that does
corvair crank prep including nitriding but I can't seem to find it in
WW's manual or in the archives.
Anybody know this place and have info on them?
Bill Pagan
http://www.matronics.com/Navigator?Zenith-List<http://www.matronics.com/N
avigator?Zenith-List>
http://www.matronics.com/contribution<http://www.matronics.com/contributi
on>
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Signed off to Solo the Sabrina Mark 1 !!! |
Sabrina,
A little trick I learned about controlling the bike at slow speed is to use brake
torque. I can ride my Harley Ultra Classic through that course now. It takes
some practice but I can slow speed steer my bike lock to lock at a slow walking
speed and never touch the ground with my feet.
It goes like this: Hold RPM to about 1800, slip the clutch so the bike will move,
and control the speed with the rear brake.
--------
Ron Lendon, Clinton Township, MI
WW Corvair with Roy's Garage 5th bearing
Zodiac XL, ScrapBuilder ;-)
http://www.mykitlog.com/rlendon
Corvair Engine Prints:
http://home.comcast.net/~rlendon/site/
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=261363#261363
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Corvair Crank Prep |
This is the place that did mine.
http://www.moldexcrankshaft.com/
contact Joe @ 313-561-7676 or 313-387-6099 with any questions and pricing. Fax
313-5617024 joe@moldexcrankshaft.com
--------
Ron Lendon, Clinton Township, MI
WW Corvair with Roy's Garage 5th bearing
Zodiac XL, ScrapBuilder ;-)
http://www.mykitlog.com/rlendon
Corvair Engine Prints:
http://home.comcast.net/~rlendon/site/
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=261365#261365
Message 7
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Report no. 2 from Sun n Fun - The Heintz clan reactions |
to.
It seems like it might if my foot was now at an angle to the pedal which is causing
more pressure on the inside of my foot versus across the whole.
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=261367#261367
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|