Today's Message Index:
----------------------
1. 03:40 AM - Re: Aileron Trim Tab Motor access. (Thruster87)
2. 06:47 AM - Re: First flight (PatrickW)
3. 08:45 AM - Re: MSC industrial supply co. (Randy L. Thwing)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Aileron Trim Tab Motor access. |
I used anchor nuts. attached them to a frame [0.025 sheet] around the servo motor
and it works just fine.Used the computer type plastic plugs[6 pin] for the
wiring connection.Cheers
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=264671#264671
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: First flight |
Woo Hoo!
Very much looking forward to reading about your experiences as you enter Phase
1 testing...
Patrick
N63PZ
90.0001%.......
--------
Patrick
XL/650/Corvair
N63PZ (reserved)
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=264689#264689
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: MSC industrial supply co. |
do not archive
For all of you that have been "skinned" on shipping by MSC, here's a
chance to get even, if you need 75 bucks worth, today only.
Regards,
Randy, Las Vegas
Enter SUPERSHIPW in the promotional code box in the Shopping
Cart when ordering online or mention the code when ordering via phone to
receive Free Shipping. Free Shipping will be reflected at Checkout.
* Certain exclusions apply. Offer subject to change or
cancellation without notice. Free Shipping not valid on COD orders. Free
Shipping is valid on all small parcel standard ground orders including
Next Day Air Saver for customers who do not participate in any UPS
Collect, 3rd Party Billing, or Consignee Billing Program. Offer is not
valid for any Premium Air Upgrades. Offer ends at 11:30pm EDT.
----- Original Message -----
From: Bill Naumuk
To: zenith-list@matronics.com
Sent: Tuesday, September 22, 2009 7:16 AM
Subject: Re: Zenith-List: MSC industrial supply co.
Carlos-
You're not the only one who got bit by MSC. My condolences.
It has nothing to do with trans-border shipping, MSC charges a
flat $10 US "Handling fee" per order (Or at least they used to). MSC
primarily deals with tool shops and the like that maintain open accounts
and seem to make a point of raping the little guy. I bought 2 ball mills
from them that cataloged at about $7 US and was charged $16 for
shipping. They would have fit in an envelope!!
One lister said he could drop ship you bits for about $2 each. He
didn't notice the 12" length, but you probably could have found them
locally for a lot less money. I bought my 16"x 5/16" bit at TrueValue
Hardware for $15.95 US.
Hang in there, bud.
Bill
do not archive
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|