Today's Message Index:
----------------------
1. 06:55 AM - Tool for Removing Rivets (Dr. Andrew Elliott)
2. 12:15 PM - Re: Tool for Removing Rivets (Thruster87)
3. 03:25 PM - Prop choice (Bill Naumuk)
4. 03:44 PM - Prop choice (Bill Naumuk)
5. 07:30 PM - Re: Tool for Removing Rivets (Tim Juhl)
6. 11:08 PM - Push/Pull tubes (Afterfxllc@aol.com)
7. 11:16 PM - Re: Re: Tool for Removing Rivets (Afterfxllc@AOL.COM)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Tool for Removing Rivets |
Folks:
If you will be deconstructing your plane, you're going to need to remove
a *LOT* of rivets. And when building (or rebuilding), you'll definitely
want to re-do any rivet that seems even the least bit marginal. The
best and safest way to remove a pulled rivet without damaging the
material or the hole is to:
1. Punch out the rivet mandrel.
2. Carefully drill off the rivet head.
3. Drill or punch out the rivet body.
I have developed a specialty tool for punching out the rivet mandrels
which will make the job much, much easier. By getting a large number of
the punch pins made, I was able to lower the cost per pin, so I can
offer these to builders at a reasonable price. Not trying to get rich,
just make back my costs. Also not a web guru (!), as you will see from
the description page:
http://members.cox.net/n601ge/punch/autopunch.html
Please take a look. Orders will be filled immediately *after*
Christmas! Be sure to include your shipping address in a note with
payment.
Thanks,
Andy Elliott, Mesa, AZ
N601GE,601XL/TD,Corvair
150 hours
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Tool for Removing Rivets |
I would be really surprised if you could remove 5/23" solid rivets with this tool,
but to knock the tails from pops would work .I used a 3X rivet gun with a
special pin punch attachment on the spar rivets and they where still pretty tough
to get out.I do use a similar tool as a center punch,spring loaded but you
can't hit it with a hammer as the spring tends to absorb the impact. Cheers
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=278600#278600
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
All-
I'm interested in hearing about your prop choices for HDSs (Corvair
or 100hp), size, type, pitch and performance. Thanks, and Merry
Christmas!
Bill Naumuk
Townville, Pa.
HDS N601MG/Corvair 95%
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
All-
I'm interested in hearing about your prop choices for HDSs (Corvair
or 100hp), size, type, pitch and performance. Thanks, and Merry
Christmas!
Bill Naumuk
Townville, Pa.
HDS N601MG/Corvair 95%
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Tool for Removing Rivets |
Nice Andy! I'll send you a check.
Merry Xmas!
Tim
--------
______________
CFII
Champ L16A flying
Zodiac XL - Jabiru 3300A
Working on fuselage
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=278641#278641
Message 6
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Push/Pull tubes almost finished
_http://www.youtube.com/watch?v=AEasX8DuXZk_
(http://www.youtube.com/watch?v=AEasX8DuXZk)
_http://www.youtube.com/watch?v=fIvQMOE0RpQ_
(http://www.youtube.com/watch?v=fIvQMOE0RpQ)
Message 7
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Tool for Removing Rivets |
It isn't all that hard to remove them..... here is a video of exactly how
to do it.
_http://www.youtube.com/watch?v=gr24Nvs7fd0_
(http://www.youtube.com/watch?v=gr24Nvs7fd0)
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|