Today's Message Index:
----------------------
1. 04:41 AM - Re: glue for rubber floor mat? (Klaus Truemper)
2. 08:46 AM - Re: Zuse a car flenith-List: glue for rubber floor mat? (Juan Vega)
3. 07:38 PM - Canopy Air Vent (Don Honabach)
4. 08:16 PM - CopperState (Michael Daniels)
5. 08:36 PM - Re: CopperState (Don Honabach)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: glue for rubber floor mat? |
Hi,
Regarding the comment
"Thin Stainless sheeting is a pretty good conductor of heat, so it would not
protect rubber hoses very well if it was in contact or very close.That's why it
is recommended to use thermal-insulated hose covers where heat may cause problems
"
The tape has excellent reflective properties of heat radiation, much better than
a black hose.
I have used it with very good results. But of course thermal insulted hose covers
are the
standard approach.
Happy flying,
Klaus
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Zuse a car flenith-List: glue for rubber floor mat? |
just
use a car floor mat with cut slits for pedals. Never glue casue is sucks to take
off.
Juan
-----Original Message-----
>From: Peter Chapman <pchap@primus.ca>
>Sent: Sep 28, 2010 2:30 PM
>To: zenith-list@matronics.com
>Subject: Zenith-List: glue for rubber floor mat?
>
>
>
>I'm trying to re-glue a thin rubber floor mat.
>
>Any suggestions on a glue?
>
>An alternative would be to attach velcro to the mat & floor, allowing
>for easier access, but it often seems that velcro holds better than
>the glue it is attached with. Grit does get down there and needs to
>be vacuumed out from time to time.
>
>Just the way I sit in the HDS, I put a lot of pressure on the mat at
>my heels, any time I move in the seat, pushing the floor mat into the
>pedals unless the mat is well secured.
>
>
>Peter Chapman
>Toronto, ON 601 HDS / 912 / C-GZDC
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Has anyone used a Canopy Air Vent(s) and has any advice/opinion on if they are
worth it?
I have the two air vents installed (one pilot/one passenger) on the fuselage side
that vent into the cabin that work great in flight on my 601HDS, but holding/wait
times on the ground they don't do much if anything.
The airport I fly out has some long hold times during peak periods. This morning
was about 15 to 20 minutes at Deer Valley (KDVT) and opening up the canopy post
pre-flight is a bit of pain and so on. Add in Phoenix, Arizona heat and it
definitely gets toasty at times.
My hope was that the canopy vents would catch my idle prop and act more like an
open/cracked canopy.... any thoughts?
As an aside, I'll be flying my 601HDS into Copperstate next month - hopefully some
other Zenith builders are coming as well.
Thanks,
Don Honabach
Tempe, AZ
601HDS - Jabiru 3300A (150+ Hours)
-----Original Message-----
From: owner-zenith-list-server@matronics.com [mailto:owner-zenith-list-server@matronics.com] On Behalf Of Juan Vega
Sent: Thursday, September 30, 2010 8:44 AM
Subject: Zenith-List: Re: Zuse a car flenith-List: glue for rubber floor mat?
just
use a car floor mat with cut slits for pedals. Never glue casue is sucks to take
off.
Juan
-----Original Message-----
>From: Peter Chapman <pchap@primus.ca>
>Sent: Sep 28, 2010 2:30 PM
>To: zenith-list@matronics.com
>Subject: Zenith-List: glue for rubber floor mat?
>
>
>
>I'm trying to re-glue a thin rubber floor mat.
>
>Any suggestions on a glue?
>
>An alternative would be to attach velcro to the mat & floor, allowing
>for easier access, but it often seems that velcro holds better than the
>glue it is attached with. Grit does get down there and needs to be
>vacuumed out from time to time.
>
>Just the way I sit in the HDS, I put a lot of pressure on the mat at my
>heels, any time I move in the seat, pushing the floor mat into the
>pedals unless the mat is well secured.
>
>
>Peter Chapman
>Toronto, ON 601 HDS / 912 / C-GZDC
>
>
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Any Zeniths going to CopperSate Fly-in?
--
Mike Daniels,
Twitter: Mike_Flys
Mytransponder: MJD
Podcast: http://www.milehighflyers.com
My airplane build site: http://www.mykitlog.com/buells2t/
YouTube: http://www.youtube.com/buells2t
http://mike-daniels.blogspot.com
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
I'll be flying in - haven't decided if I'm going multiple days or what yet
though. Probably a definite for Friday, just haven't decided about Thursday
and Saturday yet. I'm local to the area, so I may just fly-in each day ...
Don Honabach
601HDS
Do Not Archive
From: owner-zenith-list-server@matronics.com [mailto:owner-zenith-list-serv
er@matronics.com] On Behalf Of Michael Daniels
Sent: Thursday, September 30, 2010 8:11 PM
Subject: Zenith-List: CopperState
Any Zeniths going to CopperSate Fly-in?
--
Mike Daniels,
Twitter: Mike_Flys
Mytransponder: MJD
Podcast: http://www.milehighflyers.com
My airplane build site: http://www.mykitlog.com/buells2t/
YouTube: http://www.youtube.com/buells2t
http://mike-daniels.blogspot.com
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|