---------------------------------------------------------- Zenith-List Digest Archive --- Total Messages Posted Thu 09/30/10: 5 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 04:41 AM - Re: glue for rubber floor mat? (Klaus Truemper) 2. 08:46 AM - Re: Zuse a car flenith-List: glue for rubber floor mat? (Juan Vega) 3. 07:38 PM - Canopy Air Vent (Don Honabach) 4. 08:16 PM - CopperState (Michael Daniels) 5. 08:36 PM - Re: CopperState (Don Honabach) ________________________________ Message 1 _____________________________________ Time: 04:41:56 AM PST US From: Klaus Truemper Subject: Zenith-List: Re: glue for rubber floor mat? Hi, Regarding the comment "Thin Stainless sheeting is a pretty good conductor of heat, so it would not protect rubber hoses very well if it was in contact or very close.That's why it is recommended to use thermal-insulated hose covers where heat may cause problems " The tape has excellent reflective properties of heat radiation, much better than a black hose. I have used it with very good results. But of course thermal insulted hose covers are the standard approach. Happy flying, Klaus ________________________________ Message 2 _____________________________________ Time: 08:46:30 AM PST US From: Juan Vega Subject: Zenith-List: Re: Zuse a car flenith-List: glue for rubber floor mat? just use a car floor mat with cut slits for pedals. Never glue casue is sucks to take off. Juan -----Original Message----- >From: Peter Chapman >Sent: Sep 28, 2010 2:30 PM >To: zenith-list@matronics.com >Subject: Zenith-List: glue for rubber floor mat? > > > >I'm trying to re-glue a thin rubber floor mat. > >Any suggestions on a glue? > >An alternative would be to attach velcro to the mat & floor, allowing >for easier access, but it often seems that velcro holds better than >the glue it is attached with. Grit does get down there and needs to >be vacuumed out from time to time. > >Just the way I sit in the HDS, I put a lot of pressure on the mat at >my heels, any time I move in the seat, pushing the floor mat into the >pedals unless the mat is well secured. > > >Peter Chapman >Toronto, ON 601 HDS / 912 / C-GZDC > > ________________________________ Message 3 _____________________________________ Time: 07:38:41 PM PST US From: Don Honabach Subject: Zenith-List: Canopy Air Vent Has anyone used a Canopy Air Vent(s) and has any advice/opinion on if they are worth it? I have the two air vents installed (one pilot/one passenger) on the fuselage side that vent into the cabin that work great in flight on my 601HDS, but holding/wait times on the ground they don't do much if anything. The airport I fly out has some long hold times during peak periods. This morning was about 15 to 20 minutes at Deer Valley (KDVT) and opening up the canopy post pre-flight is a bit of pain and so on. Add in Phoenix, Arizona heat and it definitely gets toasty at times. My hope was that the canopy vents would catch my idle prop and act more like an open/cracked canopy.... any thoughts? As an aside, I'll be flying my 601HDS into Copperstate next month - hopefully some other Zenith builders are coming as well. Thanks, Don Honabach Tempe, AZ 601HDS - Jabiru 3300A (150+ Hours) -----Original Message----- From: owner-zenith-list-server@matronics.com [mailto:owner-zenith-list-server@matronics.com] On Behalf Of Juan Vega Sent: Thursday, September 30, 2010 8:44 AM Subject: Zenith-List: Re: Zuse a car flenith-List: glue for rubber floor mat? just use a car floor mat with cut slits for pedals. Never glue casue is sucks to take off. Juan -----Original Message----- >From: Peter Chapman >Sent: Sep 28, 2010 2:30 PM >To: zenith-list@matronics.com >Subject: Zenith-List: glue for rubber floor mat? > > > >I'm trying to re-glue a thin rubber floor mat. > >Any suggestions on a glue? > >An alternative would be to attach velcro to the mat & floor, allowing >for easier access, but it often seems that velcro holds better than the >glue it is attached with. Grit does get down there and needs to be >vacuumed out from time to time. > >Just the way I sit in the HDS, I put a lot of pressure on the mat at my >heels, any time I move in the seat, pushing the floor mat into the >pedals unless the mat is well secured. > > >Peter Chapman >Toronto, ON 601 HDS / 912 / C-GZDC > > ________________________________ Message 4 _____________________________________ Time: 08:16:08 PM PST US Subject: Zenith-List: CopperState From: Michael Daniels Any Zeniths going to CopperSate Fly-in? -- Mike Daniels, Twitter: Mike_Flys Mytransponder: MJD Podcast: http://www.milehighflyers.com My airplane build site: http://www.mykitlog.com/buells2t/ YouTube: http://www.youtube.com/buells2t http://mike-daniels.blogspot.com ________________________________ Message 5 _____________________________________ Time: 08:36:10 PM PST US From: Don Honabach Subject: RE: Zenith-List: CopperState I'll be flying in - haven't decided if I'm going multiple days or what yet though. Probably a definite for Friday, just haven't decided about Thursday and Saturday yet. I'm local to the area, so I may just fly-in each day ... Don Honabach 601HDS Do Not Archive From: owner-zenith-list-server@matronics.com [mailto:owner-zenith-list-serv er@matronics.com] On Behalf Of Michael Daniels Sent: Thursday, September 30, 2010 8:11 PM Subject: Zenith-List: CopperState Any Zeniths going to CopperSate Fly-in? -- Mike Daniels, Twitter: Mike_Flys Mytransponder: MJD Podcast: http://www.milehighflyers.com My airplane build site: http://www.mykitlog.com/buells2t/ YouTube: http://www.youtube.com/buells2t http://mike-daniels.blogspot.com ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message zenith-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Zenith-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/zenith-list Browse Digests http://www.matronics.com/digest/zenith-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.