---------------------------------------------------------- Zenith-List Digest Archive --- Total Messages Posted Tue 05/17/11: 5 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 02:44 PM - Electrical Problem with Ray Allen Indicator? (Jeffrey J Paris) 2. 03:02 PM - Re: Electrical Problem with Ray Allen Indicator? (george may) 3. 03:54 PM - Re: Electrical Problem with Ray Allen Indicator? (Craig Payne) 4. 06:07 PM - Re: Electrical Problem with Ray Allen Indicator? (Paul Mulwitz) 5. 11:17 PM - Re: Electrical Problem with Ray Allen Indicator? (Thruster87) ________________________________ Message 1 _____________________________________ Time: 02:44:13 PM PST US From: "Jeffrey J Paris" Subject: Zenith-List: Electrical Problem with Ray Allen Indicator? Hey Zentih Guys, =C2- Quick question- I have got bothRay Allen =C2-aileron and elevator trim on my CH601XLB, which work off a Ray Allen G205 hand grip, before the mods the system worked fine ,however, now that I'm back to test flying and de-bugging I have a problem with my elevator servo. =C2-The elevator indicator won't come on line and =C2-indicate, my trims work well, however, I must have m ade a bad connection somewhere and I just can't seem to find where it is. =C2-I have sent the indicator back to Ray Allen's and it came back saying that the indicator was fine and I am now completely lost and wonder if anybo dy else has any experience with his sort of mishap. =C2- I fully admit that I'm not that comfortable with all things electric andothe r than continuity tests and checking for voltage I really don't have the ele ctrical savvy to determine what is wrong. =C2-Thanks for your time and con siderstion. =C2- Jeff Paris N196ZP CH601XLB Rochester, NY ________________________________ Message 2 _____________________________________ Time: 03:02:23 PM PST US From: george may Subject: RE: Zenith-List: Electrical Problem with Ray Allen Indicator? Jeff-- Even though Ray Allen indicated all is well =2Cyou might try pushing on t he faceplate of the indicator. I've had two units become intermittent=2C w ith this symptom=2C after about a year of use. I found out that they had a bad set of boards years ago. I assume that since you wired it correctly onc e=2C you probably did it correctly the second time. Good luck George May Zodiac 601XLB 912s ---392hrs From: jeffrey-j-paris@excite.com Subject: Zenith-List: Electrical Problem with Ray Allen Indicator? Hey Zentih Guys=2C Quick question- I have got bothRay Allen aileron and elevator trim on my C H601XLB=2C which work off a Ray Allen G205 hand grip=2C before the mods the system worked fine =2Chowever=2C now that I'm back to test flying and de-b ugging I have a problem with my elevator servo. The elevator indicator won 't come on line and indicate=2C my trims work well=2C however=2C I must ha ve made a bad connection somewhere and I just can't seem to find where it i s. I have sent the indicator back to Ray Allen's and it came back saying t hat the indicator was fine and I am now completely lost and wonder if anybo dy else has any experience with his sort of mishap. I fully admit that I'm not that comfortable with all things electric andoth er than continuity tests and checking for voltage I really don't have the e lectrical savvy to determine what is wrong. Thanks for your time and consi derstion. Jeff Paris N196ZP CH601XLB Rochester=2C NY ________________________________ Message 3 _____________________________________ Time: 03:54:54 PM PST US From: "Craig Payne" Subject: RE: Zenith-List: Electrical Problem with Ray Allen Indicator? Based on my notes on the RAC position sender and display (the LED version, not the "pointer" version) this is what you can measure with a volt meter: with the sender connected the display moving the sender from one extreme to another you should see the voltage on the green wire vary from 0.21 to 1.25 volts. -- Craig ________________________________ Message 4 _____________________________________ Time: 06:07:11 PM PST US From: Paul Mulwitz Subject: Re: Zenith-List: Electrical Problem with Ray Allen Indicator? Hi Jeff, I'm afraid it is just a case of verifying continuity on the wires from the servo to the indicator. If you have developed a short you can find it by buzzing from each of the leads to ground and battery voltage. If all else fails you can run fresh wiring from the indicator to the servo and wherever else it goes. Good luck, Paul XL getting close - just installed all the placards and working on seat cushion. On 5/17/2011 2:40 PM, Jeffrey J Paris wrote: > Hey Zentih Guys, > Quick question- I have got bothRay Allen aileron and elevator trim on > my CH601XLB, which work off a Ray Allen G205 hand grip, before the > mods the system worked fine ,however, now that I'm back to test flying > and de-bugging I have a problem with my elevator servo. The elevator > indicator won't come on line and indicate, my trims work well, > however, I must have made a bad connection somewhere and I just can't > seem to find where it is. I have sent the indicator back to Ray > Allen's and it came back saying that the indicator was fine and I am > now completely lost and wonder if anybody else has any experience with > his sort of mishap. > I fully admit that I'm not that comfortable with all things electric > andother than continuity tests and checking for voltage I really don't > have the electrical savvy to determine what is wrong. Thanks for your > time and considerstion. > Jeff Paris N196ZP CH601XLB Rochester, NY > * > > > * ________________________________ Message 5 _____________________________________ Time: 11:17:35 PM PST US Subject: Zenith-List: Re: Electrical Problem with Ray Allen Indicator? From: "Thruster87" After 15hrs TT [last week] my Aileron Ray Allen LED indicator stopped working as well.Elevator LED indicator working just fine so far.Bit of a pain in the neck as mine are located on the center panel and access requires removal.Keep us posted on what the end results are Cheers Alan Read this topic online here: http://forums.matronics.com/viewtopic.php?p=340240#340240 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message zenith-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Zenith-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/zenith-list Browse Digests http://www.matronics.com/digest/zenith-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.