Today's Message Index:
----------------------
1. 04:07 AM - Re: [Probable Spam] 601 XL bearing bloc material (Malcolm Hunt)
2. 11:24 AM - Re: Zenith-List Digest: 7 Msgs - 10/03/11 (Bill Shirley Mitchell)
3. 11:54 AM - Re: Re: Zenith-List Digest: 7 Msgs - 10/03/11 (Steve Freeman)
4. 12:46 PM - Re: Re: Zenith-List Digest: 7 Msgs - 10/03/11 (Carlos Sa)
5. 12:54 PM - Re: Re: Zenith-List Digest: 7 Msgs - 10/03/11 (Bill Pagan)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | 601 XL bearing bloc material |
Michael
I have seen both. These materials are designed to be used as shaft
bearings spinning at some speed. The friction generated by the nose
strut is by comparison of a much lower order. Don=99t forget to
grease the strut prior to installation both bearings
Malcolm
From: owner-zenith-list-server@matronics.com
[mailto:owner-zenith-list-server@matronics.com] On Behalf Of Michel
Therrien
Sent: 04 October 2011 04:24
Subject: Re: [Probable Spam] Zenith-List: 601 XL bearing bloc material
I noticed different varieties of Nyloil... there is the green one and
then, the MDX (gray or blue). Are they interchangeable? It appears
that the kit part is the grey Nyloil (that is filled with Moly...).
Michel
----------------------------
Michel Therrien CH601-HD, C-GZGQ
http://mthobby.pcperfect.com/ch601
http://pages.infinit.net/mthobby
From: Malcolm Hunt <malcolmhunt@mha1.fsbusiness.co.uk>
Sent: Monday, October 3, 2011 10:37:46 AM
Subject: RE: [Probable Spam] Zenith-List: 601 XL bearing bloc material
Hi Michael
The plans call up Nyoil @ 1.5=9D thick, can be obtained in England
so should be easy with you.
Nylon is not the easiest to work but the part from the factory is
expensive.
Hope this helps
Malcolm Hunt
Plans builder in England
From: owner-zenith-list-server@matronics.com
[mailto:owner-zenith-list-server@matronics.com] On Behalf Of Larry
McFarland
Sent: 03 October 2011 14:51
Subject: RE: [Probable Spam] Zenith-List: 601 XL bearing bloc material
HI Michel,
I=99m using UHMWE at 3/8-inch thickness that replaced Nylon that
absorbed water.
Not so expensive and easy to work.
Reasonable Source: http://www.k-mac-plastics.net/index.htm
Larry McFarland 601HDS at www.macsmachine.com
<http://www.macsmachine.com/>
From: owner-zenith-list-server@matronics.com
[mailto:owner-zenith-list-server@matronics.com] On Behalf Of Michel
Therrien
Sent: Monday, October 03, 2011 6:35 AM
Subject: [Probable Spam] Zenith-List: 601 XL bearing bloc material
Hello group,
As part orf my 601 renovation project, I want to replace the lower nose
wheel fork bearing with the newer style 601 XL plastic bloc. I would
like to know what material is mandated (delrin, nylon, acetal, UHMWE?)
and what is the thickness.
Thanks!
Michel
do not archive
----------------------------
Michel Therrien CH601-HD, C-GZGQ
http://mthobby.pcperfect.com/ch601
http://pages.infinit.net/mthobby
From: Larry McFarland <larry@macsmachine.com>
Sent: Wednesday, September 28, 2011 2:46:58 PM
Subject: Zenith-List: access panel drawing
Hi guys,
I=99ve had a few people ask about a drawing for the inspection
panels I use on my 601HDS.
The link below will get you to the drawing on my site and clicking the
drawing at the bottom
of the page will get you to a larger image that=99s printable. The
panels serve my plane well
and have never given any difficulty. If you want to make a set of
these, the drawing is
a good guide.
http://www.macsmachine.com/html/winginsppanels.htm
Fly safe guys,
Larry McFarland 601HDS at www.macsmachine.com
<http://www.macsmachine.com/>
el=nofollow
target=_blank>http://www.matronics.com/Navigator?Zenith-List
et=_blank>http://forums.matronics.com <http://forums.matronics.com/>
llow target=_blank>http://www.matronics.com/contribution
http://www.matronics.com/Navigator?Zenith-List
http://forums.matronics.com <http://forums.matronics.com/>
http://www.matronics.com/contribution
http://www.matronics.com/Navigator?Zenith-List
http://forums.matronics.com
http://www.matronics.com/contribution
__________ Information from ESET Smart Security, version of virus
signature database 6512 (20111003) __________
The message was checked by ESET Smart Security.
el=nofollow
target=_blank>http://www.matronics.com/Navigator?Zenith-List
et=_blank>http://forums.matronics.com
low target=_blank>http://www.matronics.com/contribution
__________ Information from ESET Smart Security, version of virus
signature database 6515 (20111004) __________
The message was checked by ESET Smart Security.
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Zenith-List Digest: 7 Msgs - 10/03/11 |
William is deceased & we would like to retain this email but be deleted
from these mailings. How do we go about doing that? =0AMitchell family=0A
=0A=0A________________________________=0AFrom: Zenith-List Digest Server &l
t;zenith-list@matronics.com>=0ATo: Zenith-List Digest List <zenith-li
st-digest@matronics.com>=0ASent: Tuesday, October 4, 2011 12:00 AM=0ASub
ject: Zenith-List Digest: 7 Msgs - 10/03/11=0A=0A*=0A=0A======
====================0A- Online Vers
ions of Today's List Digest Archive=0A===========
===============0A=0AToday's complete Zenith
-List Digest can also be found in either of the =0Atwo Web Links listed bel
ow.- The .html file includes the Digest formatted =0Ain HTML for viewing
with a web browser and features Hyperlinked Indexes =0Aand Message Navigati
on.- The .txt file includes the plain ASCII version =0Aof the Zenith-List
Digest and can be viewed with a generic text editor =0Asuch as Notepad or
with a web browser. =0A=0AHTML Version:=0A=0A- - http://www.matronics.c
om/digest/digestview.php?Style=82701&View=html&Chapter 11-1
0-03&Archive=Zenith=0A=0AText Version:=0A=0A- - http://www.matron
ics.com/digest/digestview.php?Style=82701&View=txt&Chapter
11-10-03&Archive=Zenith=0A=0A=0A============
============0A- EMail Version of Today's List D
igest Archive=0A===================
=====0A=0A=0A- - - - - ----------------------------------
------------------------=0A- - - - - - - - - - - -
- Zenith-List Digest Archive=0A- - - - - - - - - -
- - - - - - - - - ---=0A- - - - - - - -
- - Total Messages Posted Mon 10/03/11: 7=0A- - - - - -------
---------------------------------------------------=0A=0A=0AToday's Mes
sage Index:=0A----------------------=0A=0A- - 1. 04:38 AM - 601 XL bear
ing bloc material- (Michel Therrien)=0A- - 2. 05:09 AM - Re: 601 XL b
earing bloc material- (Paul Mulwitz)=0A- - 3. 06:53 AM - Re: [Probabl
e Spam] 601 XL bearing bloc material- (Larry McFarland)=0A- - 4. 07:4
0 AM - Re: [Probable Spam] 601 XL bearing bloc material- (Malcolm Hunt)
=0A- - 5. 09:31 AM - Re: [Probable Spam] 601 XL bearing bloc material
- (Michel Therrien)=0A- - 6. 10:26 AM - Re: [Probable Spam] 601 XL be
aring bloc material- (Larry McFarland)=0A- - 7. 08:26 PM - Re: [Proba
ble Spam] 601 XL bearing bloc material- (Michel Therrien)=0A=0A=0A=0A____
____________________________- Message 1- ______________________________
_______=0A=0A=0ATime: 04:38:17 AM PST US=0AFrom: Michel Therrien <mtherr
@yahoo.com>=0ASubject: Zenith-List: 601 XL bearing bloc material=0A=0AHe
llo group,=0A=C2-=0AAs part orf my 601 renovation project, I want to
re=0Aplace the lower nose wheel fork bearing with the newer style 601 XL pl
astic=0Abloc.=C2- I would like to know what material is mandated (delrin,
nylon,=0Aacetal, UHMWE?) and what is the thickness.=0A=C2-=0AThanks!
=0A=C2-=0AM=0Aichel=0A=C2-=0Ado not archive=0A=0A----------
------------------=0AMichel =0ATherrien CH601-HD, C-GZGQ=0Ahttp://mthob
by.pcperfect.com/ch601=0Ahttp://pag=0Aes.infinit.net/mthobby=0A=0A=
0A________________________________=0AFrom: Lar=0Ary McFarland <larry@m
acsmachine.com>=0ATo: Zenith-List <zenith-list@matroni=0Acs.com>
=0ASent: Wednesday, September 28, 2011 2:46:58 PM=0ASubject: Zenith-=0A
List: access panel drawing =0A=0A=0AHi guys,=0AI=99ve had a few p
eopl=0Ae ask about a drawing for the inspection panels I use on my 601HDS.
=0AThe =0Alink below will get you to the drawing on my site and clicking
the drawing =0Aat the bottom =0Aof the page will get you to a larger imag
e that=99s =0Aprintable. The panels serve my plane well=0Aand have neve
r given any diffic=0Aulty. =C2-If you want to make a set of these, the dr
awing is =0Aa good gu=0Aide.=0A=C2-=0Ahttp://www.macsmachine.com/ht
ml/winginsppanels.htm=0A=C2-=0A=0A=C2-=0AFly safe guys,=0A=C2
-=0ALarry McFarland=C2- 601HDS at www.m=0A=========
============ =0A=0A________________________________
- Message 2- _____________________________________=0A=0A=0ATime: 05:09:
52 AM PST US=0AFrom: Paul Mulwitz <psm@att.net>=0ASubject: Re: Zenith
-List: 601 XL bearing bloc material=0A=0AHi Michael,=0A=0AI'm not sure
whether mine is the old or new stuff, but I think it is =0ANyloil -- oil im
pregnated nylon.=0A=0APaul=0AXL in flight test=0A=0AOn 10/3/2011 4:35 AM, M
ichel Therrien wrote:=0A> Hello group,=0A> As part orf my 601 renovat
ion project, I want to replace the lower =0A> nose wheel fork bearing wi
th the newer style 601 XL plastic bloc.- I =0A> would like to know wha
t material is mandated (delrin, nylon, acetal, =0A> UHMWE?) and what is
the thickness.=0A> Thanks!=0A> Michel=0A> do not archive=0A> --
--------------------------=0A> Michel Therrien CH601-HD, C-GZGQ=0A> h
ttp://mthobby.pcperfect.com/ch601=0A> http://pages.infinit.net/mthobby
=0A> *From:* Larry McFarland <larry@macsmachine.com>=0A> *To:*
Zenith-List <zenith-list@matronics.com>=0A> *Sent:* Wednesday, Sep
tember 28, 2011 2:46:58 PM=0A> *Subject:* Zenith-List: access panel draw
ing=0A>=0A> Hi guys,=0A> Ive had a few people ask about a drawing
for the inspection panels I =0A> use on my 601HDS.=0A> The link below
will get you to the drawing on my site and clicking the =0A> drawing at
the bottom=0A> of the page will get you to a larger image thats printab
le. The =0A> panels serve my plane well=0A> and have never given any
difficulty.- If you want to make a set of =0A> these, the drawing is
=0A> a good guide.=0A> http://www.macsmachine.com/html/winginsppanels
.htm=0A> Fly safe guys,=0A> Larry McFarland- 601HDS at www.macsmach
ine.com =0A> <http://www.macsmachine.com/>=0A> *=0A>=0A>
el=nofollow target=_blank>http://www.matronics.com/Navigator?Zenith-
List=0A> et=_blank>http://forums.matronics.com=0A> llow target
=_blank>http://www.matronics.com/contribution=0A>=0A> *=0A>
=0A>=0A> *=0A>=0A>=0A> *=0A=0A______________________________
__- Message 3- _____________________________________=0A=0A=0ATime: 06:5
3:51 AM PST US=0AFrom: "Larry McFarland" <larry@macsmachine.co
m>=0ASubject: RE: [Probable Spam] Zenith-List: 601 XL bearing bloc mater
ial=0A=0AHI Michel,=0A=0AI=99m using UHMWE at 3/8-inch thickness that rep
laced Nylon that =0Aabsorbed water.- =0A=0ANot so expensive and easy to w
ork. =0A=0AReasonable Source:- http://www.k-mac-plastics.net/index.htm
=0A=0A=0ALarry McFarland- 601HDS at www.macsmachine.com=0A=0A=0AFrom: own
er-zenith-list-server@matronics.com =0A[mailto:owner-zenith-list-server@mat
ronics.com] On Behalf Of Michel =0ATherrien=0ASent: Monday, October 03, 201
1 6:35 AM=0ASubject: [Probable Spam] Zenith-List: 601 XL bearing bloc mater
ial=0A=0A=0AHello group,=0A=0A=0AAs part orf my 601 renovation project, I w
ant to replace the lower nose =0Awheel fork bearing with the newer style 60
1 XL plastic bloc.- I would =0Alike to know what material is mandated (de
lrin, nylon, acetal, UHMWE?) =0Aand what is the thickness.=0A=0A=0AThanks!
=0A=0A=0AMichel=0A=0A=0Ado not archive=0A=0A=0A----------------------------
=0AMichel Therrien CH601-HD, C-GZGQ=0Ahttp://mthobby.pcperfect.com/ch601=0A
http://pages.infinit.net/mthobby=0A=0AFrom: Larry McFarland <larry@macsm
achine.com>=0ASent: Wednesday, September 28, 2011 2:46:58 PM=0ASubject:
Zenith-List: access panel drawing =0A=0AHi guys,=0A=0AI=99ve had a few pe
ople ask about a drawing for the inspection =0Apanels I use on my 601HDS.
=0A=0AThe link below will get you to the drawing on my site and clicking th
e =0Adrawing at the bottom =0A=0Aof the page will get you to a larger image
that=99s printable. The =0Apanels serve my plane well=0A=0Aand have neve
r given any difficulty.- If you want to make a set of =0Athese, the drawi
ng is =0A=0Aa good guide.=0A=0A=0Ahttp://www.macsmachine.com/html/winginspp
anels.htm=0A=0A=0AFly safe guys,=0A=0A=0ALarry McFarland- 601HDS at www.m
acsmachine.com =0A<http://www.macsmachine.com/> =0A=0A=0Ael=nofollo
w =0Atarget=_blank>http://www.matronics.com/Navigator?Zenith-List=0Aet
=_blank>http://forums.matronics.com=0Allow target=_blank>http://w
ww.matronics.com/contribution=0A=0A=0A________________________________- M
essage 4- _____________________________________=0A=0A=0ATime: 07:40:30 AM
PST US=0AFrom: "Malcolm Hunt" <malcolmhunt@mha1.fsbusiness.co
.uk>=0ASubject: RE: [Probable Spam] Zenith-List: 601 XL bearing bloc mat
erial=0A=0AHi Michael=0A=0A=0AThe plans call up Nyoil @ 1.5=9D thick, can
be obtained in England =0Aso should be easy with you.=0A=0A=0ANylon is not
the easiest to work but the part from the factory is =0Aexpensive.=0A=0A
=0AHope this helps=0A=0A=0AMalcolm Hunt=0A=0APlans builder in England=0A=0A
=0AFrom: owner-zenith-list-server@matronics.com =0A[mailto:owner-zenith-lis
t-server@matronics.com] On Behalf Of Larry =0AMcFarland=0ASent: 03 October
2011 14:51=0ASubject: RE: [Probable Spam] Zenith-List: 601 XL bearing bloc
material=0A=0A=0AHI Michel,=0A=0AI=99m using UHMWE at 3/8-inch thickness
that replaced Nylon that =0Aabsorbed water.- =0A=0ANot so expensive and e
asy to work. =0A=0AReasonable Source:- http://www.k-mac-plastics.net/inde
x.htm =0A=0A=0ALarry McFarland- 601HDS at www.macsmachine.com=0A=0A=0AFro
m: owner-zenith-list-server@matronics.com =0A[mailto:owner-zenith-list-serv
er@matronics.com] On Behalf Of Michel =0ATherrien=0ASent: Monday, October 0
3, 2011 6:35 AM=0ASubject: [Probable Spam] Zenith-List: 601 XL bearing bloc
material=0A=0A=0AHello group,=0A=0A=0AAs part orf my 601 renovation projec
t, I want to replace the lower nose =0Awheel fork bearing with the newer st
yle 601 XL plastic bloc.- I would =0Alike to know what material is mandat
ed (delrin, nylon, acetal, UHMWE?) =0Aand what is the thickness.=0A=0A=0ATh
anks!=0A=0A=0AMichel=0A=0A=0Ado not archive=0A=0A=0A-----------------------
-----=0AMichel Therrien CH601-HD, C-GZGQ=0Ahttp://mthobby.pcperfect.com/ch6
01=0Ahttp://pages.infinit.net/mthobby=0A=0AFrom: Larry McFarland <larry@
macsmachine.com>=0ASent: Wednesday, September 28, 2011 2:46:58 PM=0ASubj
ect: Zenith-List: access panel drawing =0A=0AHi guys,=0A=0AI=99ve had a f
ew people ask about a drawing for the inspection =0Apanels I use on my 601H
DS. =0A=0AThe link below will get you to the drawing on my site and clickin
g the =0Adrawing at the bottom =0A=0Aof the page will get you to a larger i
mage that=99s printable. The =0Apanels serve my plane well=0A=0Aand have
never given any difficulty.- If you want to make a set of =0Athese, the d
rawing is =0A=0Aa good guide.=0A=0A=0Ahttp://www.macsmachine.com/html/wingi
nsppanels.htm=0A=0A=0AFly safe guys,=0A=0A=0ALarry McFarland- 601HDS at w
ww.macsmachine.com =0A<http://www.macsmachine.com/> =0A=0A=0Ael=nof
ollow =0Atarget=_blank>http://www.matronics.com/Navigator?Zenith-List
=0Aet=_blank>http://forums.matronics.com=0Allow target=_blank>htt
p://www.matronics.com/contribution=0A=0A=0Ahttp://www.matronics.com/Navigat
or?Zenith-List=0A=0Ahttp://forums.matronics.com=0A=0Ahttp://www.matronics.c
om/contribution=0A=0A=0A__________ Information from ESET Smart Security, ve
rsion of virus =0Asignature database 6512 (20111003) __________=0A=0AThe me
ssage was checked by ESET Smart Security.=0A=0A=0A_________________________
_______- Message 5- _____________________________________=0A=0A=0ATime:
09:31:00 AM PST US=0AFrom: Michel Therrien <mtherr@yahoo.com>=0ASubj
ect: Re: [Probable Spam] Zenith-List: 601 XL bearing bloc material=0A=0AI u
se 1/4 inch UHMWE flush with the original 1/8" aluminum... i noticed t
ha=0At my gear leg got a bit of wear (0.003") from movement over the
=C2-6 year=0As that the plane flew (probably constant rudder movement).
=C2- I would li=0Ake to do away of the aluminum contact on the nose wheel
... did you make it =0Aso that contact is only on the plastic part?=C2-
=0A=C2-=0AThanks!=0A=0A=C2-=0AMichel=0A=C2-=0A=0A------
----------------------=0AMichel Therrie=0An CH601-HD, C-GZGQ=0Ahttp://m
thobby.pcperfect.com/ch601=0Ahttp://pages.infi=0Anit.net/mthobby=0A=0
A=0A________________________________=0AFrom: Larry McFa=0Arland <lar
ry@macsmachine.com>=0ATo: zenith-list@matronics.com=0ASent: Monda=0A
y, October 3, 2011 9:50:31 AM=0ASubject: RE: [Probable Spam] Zenith-List:
6=0A01 XL bearing bloc material=0A=0A=0AHI Michel,=0AI=99m using
UHMWE at=0A3/8-inch thickness that replaced Nylon that absorbed water.=C
2- =0ANot s=0Ao expensive and easy to work. =0AReasonable Source:=C2-
=C2- http://www.=0Ak-mac-plastics.net/index.htm =0A=C2-=0A=C2-=
0ALarry McFarland=C2- 601=0AHDS at www.macsmachine.com=0A=C2-=0AFro
m:owner-zenith-list-server@matroni=0Acs.com [mailto:owner-zenith-list-serve
r@matronics.com] On Behalf Of Michel =0ATherrien=0ASent: Monday, October
03, 2011 6:35 AM=0ATo: zenith-list@matroni=0Acs.com=0ASubject: [Probabl
e Spam] Zenith-List: 601 XL bearing bloc material=0A=0A=C2-=0AHello g
roup,=0A=C2-=0AAs part orf my 601 renovation project, =0AI want to re
place the lower nose wheel fork bearing with the newer style 60=0A1 XL plas
tic bloc.=C2- I would like to know what material is mandated (de=0Alrin,
nylon, acetal, UHMWE?) and what is the thickness.=0A=C2-=0AThanks!=0A
=0A=C2-=0AMichel=0A=C2-=0Ado not archive=0A=C2-=0A-------
------------=0A---------=0AMichel Therrien CH601-HD, C-GZGQ=0Ahttp://mt
hobby.pcperfect.com=0A/ch601=0Ahttp://pages.infinit.net/mthobby=0AFrom:
Larry McFarland <larry@mac=0Asmachine.com>=0ATo: Zenith-List <ze
nith-list@matronics.com>=0ASent: Wednesd=0Aay, September 28, 2011 2:46
:58 PM=0ASubject: Zenith-List: access panel draw=0Aing =0AHi guys,=0A
I=99ve had a few people ask about a drawing for the=0Ainspection panels I
use on my 601HDS. =0AThe link below will get you to th=0Ae drawing on my
site and clicking the drawing at the bottom =0Aof the page =0Awill get y
ou to a larger image that=99s printable. The panels serve m=0Ay plane wel
l=0Aand have never given any difficulty. =C2-If you want to ma=0Ake a s
et of these, the drawing is =0Aa good guide.=0A=C2-=0Ahttp://www.ma
=0Acsmachine.com/html/winginsppanels.htm=0A=C2-=0A=C2-=0AFly safe
guys,=0A=0A=C2-=0ALarry McFarland=C2- 601HDS at www.macsmachine.co
m=0A=C2-=0A=C2=0A-=0A=C2-=0Ael=nofollow target=_blank>
http://www.matronics.com/Navig=0Aator?Zenith-List=0Aet=_blank>http:/
/forums.matronics.com=0Allow target==0A_blank>http://www.matronics.c
om/contribution=0A=C2-=0A=C2-=0A=C2-=0A=0A=C2-=0Ahttp://w
ww.matronics.com/Navigator?Zenith-List=0Ahttp://forums.mat=0A====
==== =0A=0A________________________________- Message 6- _______
______________________________=0A=0A=0ATime: 10:26:12 AM PST US=0AFrom: &qu
ot;Larry McFarland" <larry@macsmachine.com>=0ASubject: RE: [Prob
able Spam] Zenith-List: 601 XL bearing bloc material=0A=0AYes Michel,=0A=0A
I noticed wear in the same fore and aft areas and made adjustments to =0Ake
ep the tube =0A=0A>From being in contact with the aluminum. With the UHM
WE, that works =0Arather well.=0A=0AGet a good fit with the bearing plastic
and then remove a little =0Aaluminum for clearance.=0A=0AIt=99ll hold.
=0A=0A=0ALarry McFarland- 601HDS at www.macsmachine.com=0A=0A=0AFrom: own
er-zenith-list-server@matronics.com =0A[mailto:owner-zenith-list-server@mat
ronics.com] On Behalf Of Michel =0ATherrien=0ASent: Monday, October 03, 201
1 11:28 AM=0ASubject: Re: [Probable Spam] Zenith-List: 601 XL bearing bloc
material=0A=0A=0AI use 1/4 inch UHMWE flush with the original 1/8" alu
minum... i noticed =0Athat my gear leg got a bit of wear (0.003") from
movement over the 6 =0Ayears that the plane flew (probably constant rudder
movement).- I would =0Alike to do away of the aluminum contact on the no
se wheel... did you =0Amake it so that contact is only on the plastic part?
- =0A=0A=0AThanks!=0A=0A=0AMichel=0A=0A=0A----------------------------=0A
Michel Therrien CH601-HD, C-GZGQ=0Ahttp://mthobby.pcperfect.com/ch601=0Ahtt
p://pages.infinit.net/mthobby=0A=0AFrom: Larry McFarland <larry@macsmach
ine.com>=0ASent: Monday, October 3, 2011 9:50:31 AM=0ASubject: RE: [Prob
able Spam] Zenith-List: 601 XL bearing bloc material=0A=0AHI Michel,=0A=0AI
=99m using UHMWE at 3/8-inch thickness that replaced Nylon that =0Aabsorb
ed water.- =0A=0ANot so expensive and easy to work. =0A=0AReasonable Sour
ce:- http://www.k-mac-plastics.net/index.htm =0A=0A=0ALarry McFarland-
601HDS at www.macsmachine.com=0A=0A=0AFrom: owner-zenith-list-server@matron
ics.com =0A[mailto:owner-zenith-list-server@matronics.com] On Behalf Of Mic
hel =0ATherrien=0ASent: Monday, October 03, 2011 6:35 AM=0ASubject: [Probab
le Spam] Zenith-List: 601 XL bearing bloc material=0A=0A=0AHello group,=0A
=0A=0AAs part orf my 601 renovation project, I want to replace the lower no
se =0Awheel fork bearing with the newer style 601 XL plastic bloc.- I wou
ld =0Alike to know what material is mandated (delrin, nylon, acetal, UHMWE?
) =0Aand what is the thickness.=0A=0A=0AThanks!=0A=0A=0AMichel=0A=0A=0Ado n
ot archive=0A=0A=0A----------------------------=0AMichel Therrien CH601-HD,
C-GZGQ=0Ahttp://mthobby.pcperfect.com/ch601=0Ahttp://pages.infinit.net/mth
obby=0A=0AFrom: Larry McFarland <larry@macsmachine.com>=0ASent: Wedne
sday, September 28, 2011 2:46:58 PM=0ASubject: Zenith-List: access panel dr
awing =0A=0AHi guys,=0A=0AI=99ve had a few people ask about a drawing for
the inspection =0Apanels I use on my 601HDS. =0A=0AThe link below will get
you to the drawing on my site and clicking the =0Adrawing at the bottom
=0A=0Aof the page will get you to a larger image that=99s printable. The
=0Apanels serve my plane well=0A=0Aand have never given any difficulty.-
If you want to make a set of =0Athese, the drawing is =0A=0Aa good guide.
=0A=0A=0Ahttp://www.macsmachine.com/html/winginsppanels.htm=0A=0A=0AFly saf
e guys,=0A=0A=0ALarry McFarland- 601HDS at www.macsmachine.com =0A<htt
p://www.macsmachine.com/> =0A=0A=0Ael=nofollow =0Atarget=_blank>h
ttp://www.matronics.com/Navigator?Zenith-List=0A=0Aet=_blank>http://fo
rums.matronics.com <http://forums.matronics.com/> =0A=0Allow target
=_blank>http://www.matronics.com/contribution=0A=0A=0Ahttp://www.matro
nics.com/Navigator?Zenith-List=0Ahttp://forums.matronics.com=0Ahttp://www.m
atronics.com/contribution=0A=0A=0Ael=nofollow =0Atarget=_blank>http:
//www.matronics.com/Navigator?Zenith-List=0Aet=_blank>http://forums.ma
tronics.com=0Allow target=_blank>http://www.matronics.com/contribution
=0A=0A=0A________________________________- Message 7- _________________
____________________=0A=0A=0ATime: 08:26:16 PM PST US=0AFrom: Michel Therri
en <mtherr@yahoo.com>=0ASubject: Re: [Probable Spam] Zenith-List: 601
XL bearing bloc material=0A=0AI noticed different varieties of Nyloil... t
here is the green one and then,=0Athe MDX (gray or blue).=C2- Are they in
terchangeable?=C2- It appears t=0Ahat the kit part is the grey Nyloil (th
at is filled with Moly...).=0A=C2-=0A=0AMichel=0A=C2-=0A=0A--
--------------------------=0AMichel Therrien CH60=0A1-HD, C-GZGQ=0Ahttp
://mthobby.pcperfect.com/ch601=0Ahttp://pages.infinit.ne=0At/mthobby=0A
=0A=0A________________________________=0AFrom: Malcolm Hunt <ma=0A
lcolmhunt@mha1.fsbusiness.co.uk>=0ATo: zenith-list@matronics.com=0AS
ent: Mo=0Anday, October 3, 2011 10:37:46 AM=0ASubject: RE: [Probable Spam
] Zenith-Lis=0At: 601 XL bearing bloc material=0A=0A=0AHi Michael=0
A=C2-=0AThe plans cal=0Al up Nyoil @ 1.5=9D thick, can be obtained in
England so should be ea=0Asy with you.=0A=C2-=0ANylon is not the eas
iest to work but the part from =0Athe factory is expensive.=0A=C2-=0A
Hope this helps=0A=C2-=0AMalcolm Hun=0At=0APlans builder in England
=0A=C2-=0AFrom:owner-zenith-list-server@matro=0Anics.com [mailto:owne
r-zenith-list-server@matronics.com] On Behalf Of Larry=0AMcFarland=0ASent
: 03 October 2011 14:51=0ATo: zenith-list@matronics.com=0A=0ASubject: R
E: [Probable Spam] Zenith-List: 601 XL bearing bloc material=0A=0A=C2-
=0AHI Michel,=0AI=99m using UHMWE at 3/8-inch thickness that re=0Apla
ced Nylon that absorbed water.=C2- =0ANot so expensive and easy to wor
=0Ak. =0AReasonable Source:=C2-=C2- http://www.k-mac-plastics.net/ind
ex.ht=0Am =0A=C2-=0A=C2-=0ALarry McFarland=C2- 601HDS at www.ma
csmachine.com=0A=0A=C2-=0AFrom:owner-zenith-list-server@matronics.com
[mailto:owner-zenit=0Ah-list-server@matronics.com] On Behalf Of Michel The
rrien=0ASent: Monday, O=0Actober 03, 2011 6:35 AM=0ATo: zenith-list@mat
ronics.com=0ASubject: [Probabl=0Ae Spam] Zenith-List: 601 XL bearing bloc
material=0A=C2-=0AHello group,=0A=0A=C2-=0AAs part orf my 601
renovation project, I want to replace the lo=0Awer nose wheel fork bearing
with the newer style 601 XL plastic bloc.=C2-=0AI would like to know what
material is mandated (delrin, nylon, acetal, UHM=0AWE?) and what is the th
ickness.=0A=C2-=0AThanks!=0A=C2-=0AMichel=0A=C2=0A-=0Ado
not archive=0A=C2-=0A----------------------------=0AMichel Therr=0A
ien CH601-HD, C-GZGQ=0Ahttp://mthobby.pcperfect.com/ch601=0Ahttp://page
s.in=0Afinit.net/mthobby=0AFrom:Larry McFarland <larry@macsmachine.com
>=0ATo: Zeni=0Ath-List <zenith-list@matronics.com>=0ASent: Wed
nesday, September 28, 2011 2=0A:46:58 PM=0ASubject: Zenith-List: access p
anel drawing =0AHi guys,=0AI=0A=99ve had a few people ask about a dra
wing for the inspection panels I u=0Ase on my 601HDS. =0AThe link below w
ill get you to the drawing on my site a=0And clicking the drawing at the bo
ttom =0Aof the page will get you to a larg=0Aer image that=99s printabl
e. The panels serve my plane well=0Aand hav=0Ae never given any difficult
y. =C2-If you want to make a set of these, the=0Adrawing is =0Aa good g
uide.=0A=C2-=0Ahttp://www.macsmachine.com/html/win=0Aginsppanels.htm
=0A=C2-=0A=C2-=0AFly safe guys,=0A=C2-=0ALarry McFarla=0And
=C2- 601HDS at www.macsmachine.com=0A=C2-=0A=C2-=0A=C2-=0Ae
l=no=0Afollow target=_blank>http://www.matronics.com/Navigator?Zenit
h-List=0Aet=0A=_blank>http://forums.matronics.com=0Allow target=
_blank>http://www.mat=0Aronics.com/contribution=0A=C2-=0A=C2-=
0A=C2-=0A=C2-=0A=C2-=0Ahttp=0A://www.matronics.com/Navigator?Ze
nith-List=0A=C2-=0Ahttp://forums.matroni=0Acs.com=0A=C2-=0Ahttp
://www.matronics.com/contribution=0A=C2-=0A=C2-=0A=0A=C2-=0A
=C2-=0Ahttp://www.matronics.com/Navigator?Zenith-List=0Ahttp:=0A//for
ums.matronics.com=0Ahttp://www.matronics.com/contribution=0A=C2-=0A
=0A=0A=0A__________ Information from ESET Smart Security, version of vi
rus sig=0Anature database 6512 (20111003) __________=0A=0AThe message w
as checked by =0AESET Smart Security.=0A=0A=0Ahttp://www.matronics.co
=========================0A
- - - - - - - - - - - - - -Matt Dralle, List Admi
=====
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Zenith-List Digest: 7 Msgs - 10/03/11 |
If I remember correctly - all you need to do is send an email to the list
with UNSUBSCRIBE in the subject and the body of the email.
List - please correct me if am wrong.
Steve
From: owner-zenith-list-server@matronics.com
[mailto:owner-zenith-list-server@matronics.com] On Behalf Of Bill Shirley
Mitchell
Sent: Tuesday, October 04, 2011 11:22 AM
Subject: Zenith-List: Re: Zenith-List Digest: 7 Msgs - 10/03/11
William is deceased & we would like to retain this email but be deleted from
these mailings. How do we go about doing that?
Mitchell family
_____
From: Zenith-List Digest Server <zenith-list@matronics.com>
Sent: Tuesday, October 4, 2011 12:00 AM
Subject: Zenith-List Digest: 7 Msgs - 10/03/11
*
========================
Online Versions of Today's List Digest Archive
========================
Today's complete Zenith-List Digest can also be found in either of the
two Web Links listed below. The .html file includes the Digest formatted
in HTML for viewing with a web browser and features Hyperlinked Indexes
and Message Navigation. The .txt file includes the plain ASCII version
of the Zenith-List Digest and can be viewed with a generic text editor
such as Notepad or with a web browser.
HTML Version:
http://www.matronics.com/digest/digestview.php?Style=82701
<http://www.matronics.com/digest/digestview.php?Style=82701&View=html&Chapte
r 11-10-03&Archive=Zenith> &View=html&Chapter 11-10-03&Archive=Zenith
Text Version:
http://www.matronics.com/digest/digestview.php?Style=82701
<http://www.matronics.com/digest/digestview.php?Style=82701&View=txt&Chapter
11-10-03&Archive=Zenith> &View=txt&Chapter 11-10-03&Archive=Zenith
======================
EMail Version of Today's List Digest Archive
======================
----------------------------------------------------------
Zenith-List Digest Archive
---
Total Messages Posted Mon 10/03/11: 7
----------------------------------------------------------
Today's Message Index:
----------------------
1. 04:38 AM - 601 XL bearing bloc material (Michel Therrien)
2. 05:09 AM - Re: 601 XL bearing bloc material (Paul Mulwitz)
3. 06:53 AM - Re: [Probable Spam] 601 XL bearing bloc material (Larry
McFarland)
4. 07:40 AM - Re: [Probable Spam] 601 XL bearing bloc material (Malcolm
Hunt)
5. 09:31 AM - Re: [Probable Spam] 601 XL bearing bloc material (Michel
Therrien)
6. 10:26 AM - Re: [Probable Spam] 601 XL bearing bloc material (Larry
McFarland)
7. 08:26 PM - Re: [Probable Spam] 601 XL bearing bloc material (Michel
Therrien)
________________________________ Message 1
_____________________________________
Time: 04:38:17 AM PST US
From: Michel Therrien <mtherr@yahoo.com>
Subject: Zenith-List: 601 XL bearing bloc material
Hello group,=0A=C2-=0AAs part orf my 601 renovation project, I want to re
place the lower nose wheel fork bearing with the newer style 601 XL plastic
bloc.=C2- I would like to know what material is mandated (delrin, nylon,
acetal, UHMWE?) and what is the thickness.=0A=C2-=0AThanks!=0A=C2-=0AM
ichel=0A=C2-=0Ado not archive=0A=0A----------------------------=0AMichel
Therrien CH601-HD, C-GZGQ=0Ahttp://mthobby.pcperfect.com/ch601=0Ahttp://pag
<http://mthobby.pcperfect.com/ch601=0Ahttp:/pag>
es.infinit.net/mthobby=0A=0A=0A________________________________=0AFrom: Lar
ry McFarland <larry@macsmachine.com>=0ATo: Zenith-List <zenith-list@matroni
<mailto:zenith-list@matroni%0bcs.com>
cs.com>=0ASent: Wednesday, September 28, 2011 2:46:58 PM=0ASubject: Zenith-
List: access panel drawing =0A=0A=0AHi guys,=0AI=99ve had a few peopl
e ask about a drawing for the inspection panels I use on my 601HDS. =0AThe
link below will get you to the drawing on my site and clicking the drawing
at the bottom =0Aof the page will get you to a larger image that=99s
printable. The panels serve my plane well=0Aand have never given any diffic
ulty. =C2-If you want to make a set of these, the drawing is =0Aa good gu
ide.=0A=C2-=0Ahttp://www.macsmachine.com/html/winginsppanels.htm=0A=C2-
=0A=C2-=0AFly safe guys,=0A=C2-=0ALarry McFarland=C2- 601HDS at www.m
=====================
________________________________ Message 2
_____________________________________
Time: 05:09:52 AM PST US
From: Paul Mulwitz <psm@att.net>
Subject: Re: Zenith-List: 601 XL bearing bloc material
Hi Michael,
I'm not sure whether mine is the old or new stuff, but I think it is
Nyloil -- oil impregnated nylon.
Paul
XL in flight test
On 10/3/2011 4:35 AM, Michel Therrien wrote:
> Hello group,
> As part orf my 601 renovation project, I want to replace the lower
> nose wheel fork bearing with the newer style 601 XL plastic bloc. I
> would like to know what material is mandated (delrin, nylon, acetal,
> UHMWE?) and what is the thickness.
> Thanks!
> Michel
> do not archive
> ----------------------------
> Michel Therrien CH601-HD, C-GZGQ
> http://mthobby.pcperfect.com/ch601
> http://pages.infinit.net/mthobby
> *From:* Larry McFarland <larry@macsmachine.com>
> *To:* Zenith-List <zenith-list@matronics.com>
> *Sent:* Wednesday, September 28, 2011 2:46:58 PM
> *Subject:* Zenith-List: access panel drawing
>
> Hi guys,
> Ive had a few people ask about a drawing for the inspection panels I
> use on my 601HDS.
> The link below will get you to the drawing on my site and clicking the
> drawing at the bottom
> of the page will get you to a larger image thats printable. The
> panels serve my plane well
> and have never given any difficulty. If you want to make a set of
> these, the drawing is
> a good guide.
> http://www.macsmachine.com/html/winginsppanels.htm
> Fly safe guys,
> Larry McFarland 601HDS at www.macsmachine.com
> <http://www.macsmachine.com/>
> *
>
> el=nofollow target=_blank>http://www.matronics.com/Navigator?Zenith-List
> et=_blank>http://forums.matronics.com
> llow target=_blank>http://www.matronics.com/contribution
>
> *
>
>
> *
>
>
> *
________________________________ Message 3
_____________________________________
Time: 06:53:51 AM PST US
From: "Larry McFarland" <larry@macsmachine.com>
Subject: RE: [Probable Spam] Zenith-List: 601 XL bearing bloc material
HI Michel,
I=99m using UHMWE at 3/8-inch thickness that replaced Nylon that
absorbed water.
Not so expensive and easy to work.
Reasonable Source: http://www.k-mac-plastics.net/index.htm
Larry McFarland 601HDS at www.macsmachine.com
From: owner-zenith-list-server@matronics.com
[mailto:owner-zenith-list-server@matronics.com] On Behalf Of Michel
Therrien
Sent: Monday, October 03, 2011 6:35 AM
Subject: [Probable Spam] Zenith-List: 601 XL bearing bloc material
Hello group,
As part orf my 601 renovation project, I want to replace the lower nose
wheel fork bearing with the newer style 601 XL plastic bloc. I would
like to know what material is mandated (delrin, nylon, acetal, UHMWE?)
and what is the thickness.
Thanks!
Michel
do not archive
----------------------------
Michel Therrien CH601-HD, C-GZGQ
http://mthobby.pcperfect.com/ch601
http://pages.infinit.net/mthobby
From: Larry McFarland <larry@macsmachine.com>
Sent: Wednesday, September 28, 2011 2:46:58 PM
Subject: Zenith-List: access panel drawing
Hi guys,
I=99ve had a few people ask about a drawing for the inspection
panels I use on my 601HDS.
The link below will get you to the drawing on my site and clicking the
drawing at the bottom
of the page will get you to a larger image that=99s printable. The
panels serve my plane well
and have never given any difficulty. If you want to make a set of
these, the drawing is
a good guide.
http://www.macsmachine.com/html/winginsppanels.htm
Fly safe guys,
Larry McFarland 601HDS at www.macsmachine.com
<http://www.macsmachine.com/>
el=nofollow
target=_blank>http://www.matronics.com/Navigator?Zenith-List
et=_blank>http://forums.matronics.com
llow target=_blank>http://www.matronics.com/contribution
________________________________ Message 4
_____________________________________
Time: 07:40:30 AM PST US
From: "Malcolm Hunt" <malcolmhunt@mha1.fsbusiness.co.uk>
Subject: RE: [Probable Spam] Zenith-List: 601 XL bearing bloc material
Hi Michael
The plans call up Nyoil @ 1.5=9D thick, can be obtained in England
so should be easy with you.
Nylon is not the easiest to work but the part from the factory is
expensive.
Hope this helps
Malcolm Hunt
Plans builder in England
From: owner-zenith-list-server@matronics.com
[mailto:owner-zenith-list-server@matronics.com] On Behalf Of Larry
McFarland
Sent: 03 October 2011 14:51
Subject: RE: [Probable Spam] Zenith-List: 601 XL bearing bloc material
HI Michel,
I=99m using UHMWE at 3/8-inch thickness that replaced Nylon that
absorbed water.
Not so expensive and easy to work.
Reasonable Source: http://www.k-mac-plastics.net/index.htm
Larry McFarland 601HDS at www.macsmachine.com
From: owner-zenith-list-server@matronics.com
[mailto:owner-zenith-list-server@matronics.com] On Behalf Of Michel
Therrien
Sent: Monday, October 03, 2011 6:35 AM
Subject: [Probable Spam] Zenith-List: 601 XL bearing bloc material
Hello group,
As part orf my 601 renovation project, I want to replace the lower nose
wheel fork bearing with the newer style 601 XL plastic bloc. I would
like to know what material is mandated (delrin, nylon, acetal, UHMWE?)
and what is the thickness.
Thanks!
Michel
do not archive
----------------------------
Michel Therrien CH601-HD, C-GZGQ
http://mthobby.pcperfect.com/ch601
http://pages.infinit.net/mthobby
From: Larry McFarland <larry@macsmachine.com>
Sent: Wednesday, September 28, 2011 2:46:58 PM
Subject: Zenith-List: access panel drawing
Hi guys,
I=99ve had a few people ask about a drawing for the inspection
panels I use on my 601HDS.
The link below will get you to the drawing on my site and clicking the
drawing at the bottom
of the page will get you to a larger image that=99s printable. The
panels serve my plane well
and have never given any difficulty. If you want to make a set of
these, the drawing is
a good guide.
http://www.macsmachine.com/html/winginsppanels.htm
Fly safe guys,
Larry McFarland 601HDS at www.macsmachine.com
<http://www.macsmachine.com/>
el=nofollow
target=_blank>http://www.matronics.com/Navigator?Zenith-List
et=_blank>http://forums.matronics.com
llow target=_blank>http://www.matronics.com/contribution
http://www.matronics.com/Navigator?Zenith-List
http://forums.matronics.com
http://www.matronics.com/contribution
__________ Information from ESET Smart Security, version of virus
signature database 6512 (20111003) __________
The message was checked by ESET Smart Security.
________________________________ Message 5
_____________________________________
Time: 09:31:00 AM PST US
From: Michel Therrien <mtherr@yahoo.com>
Subject: Re: [Probable Spam] Zenith-List: 601 XL bearing bloc material
I use 1/4 inch UHMWE flush with the original 1/8" aluminum... i noticed tha
t my gear leg got a bit of wear (0.003") from movement over the=C2-6 year
s that the plane flew (probably constant rudder movement).=C2- I would li
ke to do away of the aluminum contact on the nose wheel... did you make it
so that contact is only on the plastic part?=C2- =0A=C2-=0AThanks!=0A
=C2-=0AMichel=0A=C2-=0A=0A----------------------------=0AMichel Therrie
n CH601-HD, C-GZGQ=0Ahttp://mthobby.pcperfect.com/ch601=0Ahttp://pages.infi
<http://mthobby.pcperfect.com/ch601=0Ahttp:/pages.infi>
nit.net/mthobby=0A=0A=0A________________________________=0AFrom: Larry McFa
rland <larry@macsmachine.com>=0ATo: zenith-list@matronics.com=0ASent: Monda
y, October 3, 2011 9:50:31 AM=0ASubject: RE: [Probable Spam] Zenith-List: 6
01 XL bearing bloc material=0A=0A=0AHI Michel,=0AI=99m using UHMWE at
3/8-inch thickness that replaced Nylon that absorbed water.=C2- =0ANot s
o expensive and easy to work. =0AReasonable Source:=C2-=C2- http://www.
k-mac-plastics.net/index.htm =0A=C2-=0A=C2-=0ALarry McFarland=C2- 601
HDS at www.macsmachine.com=0A=C2-=0AFrom:owner-zenith-list-server@matroni
cs.com [mailto:owner-zenith-list-server@matronics.com] On Behalf Of Michel
Therrien=0ASent: Monday, October 03, 2011 6:35 AM=0ATo: zenith-list@matroni
cs.com=0ASubject: [Probable Spam] Zenith-List: 601 XL bearing bloc material
=0A=C2-=0AHello group,=0A=C2-=0AAs part orf my 601 renovation project,
I want to replace the lower nose wheel fork bearing with the newer style 60
1 XL plastic bloc.=C2- I would like to know what material is mandated (de
lrin, nylon, acetal, UHMWE?) and what is the thickness.=0A=C2-=0AThanks!
=0A=C2-=0AMichel=0A=C2-=0Ado not archive=0A=C2-=0A-------------------
---------=0AMichel Therrien CH601-HD, C-GZGQ=0Ahttp://mthobby.pcperfect.com
/ch601=0Ahttp://pages.infinit.net/mthobby=0AFrom:Larry McFarland <larry@mac
<mailto:larry@mac%0bsmachine.com>
smachine.com>=0ATo: Zenith-List <zenith-list@matronics.com>=0ASent: Wednesd
ay, September 28, 2011 2:46:58 PM=0ASubject: Zenith-List: access panel draw
ing =0AHi guys,=0AI=99ve had a few people ask about a drawing for the
inspection panels I use on my 601HDS. =0AThe link below will get you to th
e drawing on my site and clicking the drawing at the bottom =0Aof the page
will get you to a larger image that=99s printable. The panels serve m
y plane well=0Aand have never given any difficulty. =C2-If you want to ma
ke a set of these, the drawing is =0Aa good guide.=0A=C2-=0Ahttp://www.ma
csmachine.com/html/winginsppanels.htm=0A=C2-=0A=C2-=0AFly safe guys,=0A
=C2-=0ALarry McFarland=C2- 601HDS at www.macsmachine.com=0A=C2-=0A=C2
-=0A=C2-=0Ael=nofollow target=_blank>http://www.matronics.com/Navig
ator?Zenith-List=0Aet=_blank>http://forums.matronics.com=0Allow target
_blank>http://www.matronics.com/contribution=0A=C2-=0A=C2-=0A=C2-=0A
=C2-=0Ahttp://www.matronics.com/Navigator?Zenith-List=0Ahttp://forums.mat
========
________________________________ Message 6
_____________________________________
Time: 10:26:12 AM PST US
From: "Larry McFarland" <larry@macsmachine.com>
Subject: RE: [Probable Spam] Zenith-List: 601 XL bearing bloc material
Yes Michel,
I noticed wear in the same fore and aft areas and made adjustments to
keep the tube
>From being in contact with the aluminum. With the UHMWE, that works
rather well.
Get a good fit with the bearing plastic and then remove a little
aluminum for clearance.
It=99ll hold.
Larry McFarland 601HDS at www.macsmachine.com
From: owner-zenith-list-server@matronics.com
[mailto:owner-zenith-list-server@matronics.com] On Behalf Of Michel
Therrien
Sent: Monday, October 03, 2011 11:28 AM
Subject: Re: [Probable Spam] Zenith-List: 601 XL bearing bloc material
I use 1/4 inch UHMWE flush with the original 1/8" aluminum... i noticed
that my gear leg got a bit of wear (0.003") from movement over the 6
years that the plane flew (probably constant rudder movement). I would
like to do away of the aluminum contact on the nose wheel... did you
make it so that contact is only on the plastic part?
Thanks!
Michel
----------------------------
Michel Therrien CH601-HD, C-GZGQ
http://mthobby.pcperfect.com/ch601
http://pages.infinit.net/mthobby
From: Larry McFarland <larry@macsmachine.com>
Sent: Monday, October 3, 2011 9:50:31 AM
Subject: RE: [Probable Spam] Zenith-List: 601 XL bearing bloc material
HI Michel,
I=99m using UHMWE at 3/8-inch thickness that replaced Nylon that
absorbed water.
Not so expensive and easy to work.
Reasonable Source: http://www.k-mac-plastics.net/index.htm
Larry McFarland 601HDS at www.macsmachine.com
From: owner-zenith-list-server@matronics.com
[mailto:owner-zenith-list-server@matronics.com] On Behalf Of Michel
Therrien
Sent: Monday, October 03, 2011 6:35 AM
Subject: [Probable Spam] Zenith-List: 601 XL bearing bloc material
Hello group,
As part orf my 601 renovation project, I want to replace the lower nose
wheel fork bearing with the newer style 601 XL plastic bloc. I would
like to know what material is mandated (delrin, nylon, acetal, UHMWE?)
and what is the thickness.
Thanks!
Michel
do not archive
----------------------------
Michel Therrien CH601-HD, C-GZGQ
http://mthobby.pcperfect.com/ch601
http://pages.infinit.net/mthobby
From: Larry McFarland <larry@macsmachine.com>
Sent: Wednesday, September 28, 2011 2:46:58 PM
Subject: Zenith-List: access panel drawing
Hi guys,
I=99ve had a few people ask about a drawing for the inspection
panels I use on my 601HDS.
The link below will get you to the drawing on my site and clicking the
drawing at the bottom
of the page will get you to a larger image that=99s printable. The
panels serve my plane well
and have never given any difficulty. If you want to make a set of
these, the drawing is
a good guide.
http://www.macsmachine.com/html/winginsppanels.htm
Fly safe guys,
Larry McFarland 601HDS at www.macsmachine.com
<http://www.macsmachine.com/>
el=nofollow
target=_blank>http://www.matronics.com/Navigator?Zenith-List
et=_blank>http://forums.matronics.com <http://forums.matronics.com/>
llow target=_blank>http://www.matronics.com/contribution
http://www.matronics.com/Navigator?Zenith-List
http://forums.matronics.com
http://www.matronics.com/contribution
el=nofollow
target=_blank>http://www.matronics.com/Navigator?Zenith-List
et=_blank>http://forums.matronics.com
llow target=_blank>http://www.matronics.com/contribution
________________________________ Message 7
_____________________________________
Time: 08:26:16 PM PST US
From: Michel Therrien <mtherr@yahoo.com>
Subject: Re: [Probable Spam] Zenith-List: 601 XL bearing bloc material
I noticed different varieties of Nyloil... there is the green one and then,
the MDX (gray or blue).=C2- Are they interchangeable?=C2- It appears t
hat the kit part is the grey Nyloil (that is filled with Moly...).=0A=C2-
=0AMichel=0A=C2-=0A=0A----------------------------=0AMichel Therrien CH60
1-HD, C-GZGQ=0Ahttp://mthobby.pcperfect.com/ch601=0Ahttp://pages.infinit.ne
<http://mthobby.pcperfect.com/ch601=0Ahttp:/pages.infinit.ne>
t/mthobby=0A=0A=0A________________________________=0AFrom: Malcolm Hunt <ma
lcolmhunt@mha1.fsbusiness.co.uk>=0ATo: zenith-list@matronics.com=0ASent: Mo
nday, October 3, 2011 10:37:46 AM=0ASubject: RE: [Probable Spam] Zenith-Lis
t: 601 XL bearing bloc material=0A=0A=0AHi Michael=0A=C2-=0AThe plans cal
l up Nyoil @ 1.5=9D thick, can be obtained in England so should be ea
sy with you.=0A=C2-=0ANylon is not the easiest to work but the part from
the factory is expensive.=0A=C2-=0AHope this helps=0A=C2-=0AMalcolm Hun
t=0APlans builder in England=0A=C2-=0AFrom:owner-zenith-list-server@matro
nics.com [mailto:owner-zenith-list-server@matronics.com] On Behalf Of Larry
McFarland=0ASent: 03 October 2011 14:51=0ATo: zenith-list@matronics.com=0A
Subject: RE: [Probable Spam] Zenith-List: 601 XL bearing bloc material=0A
=C2-=0AHI Michel,=0AI=99m using UHMWE at 3/8-inch thickness that re
placed Nylon that absorbed water.=C2- =0ANot so expensive and easy to wor
k. =0AReasonable Source:=C2-=C2- http://www.k-mac-plastics.net/index.ht
m =0A=C2-=0A=C2-=0ALarry McFarland=C2- 601HDS at www.macsmachine.com
=0A=C2-=0AFrom:owner-zenith-list-server@matronics.com [mailto:owner-zenit
h-list-server@matronics.com] On Behalf Of Michel Therrien=0ASent: Monday, O
ctober 03, 2011 6:35 AM=0ATo: zenith-list@matronics.com=0ASubject: [Probabl
e Spam] Zenith-List: 601 XL bearing bloc material=0A=C2-=0AHello group,
=0A=C2-=0AAs part orf my 601 renovation project, I want to replace the lo
wer nose wheel fork bearing with the newer style 601 XL plastic bloc.=C2-
I would like to know what material is mandated (delrin, nylon, acetal, UHM
WE?) and what is the thickness.=0A=C2-=0AThanks!=0A=C2-=0AMichel=0A=C2
-=0Ado not archive=0A=C2-=0A----------------------------=0AMichel Therr
ien CH601-HD, C-GZGQ=0Ahttp://mthobby.pcperfect.com/ch601=0Ahttp://pages.in
<http://mthobby.pcperfect.com/ch601=0Ahttp:/pages.in>
finit.net/mthobby=0AFrom:Larry McFarland <larry@macsmachine.com>=0ATo: Zeni
th-List <zenith-list@matronics.com>=0ASent: Wednesday, September 28, 2011 2
:46:58 PM=0ASubject: Zenith-List: access panel drawing =0AHi guys,=0AI
=99ve had a few people ask about a drawing for the inspection panels I u
se on my 601HDS. =0AThe link below will get you to the drawing on my site a
nd clicking the drawing at the bottom =0Aof the page will get you to a larg
er image that=99s printable. The panels serve my plane well=0Aand hav
e never given any difficulty. =C2-If you want to make a set of these, the
drawing is =0Aa good guide.=0A=C2-=0Ahttp://www.macsmachine.com/html/win
ginsppanels.htm=0A=C2-=0A=C2-=0AFly safe guys,=0A=C2-=0ALarry McFarla
nd=C2- 601HDS at www.macsmachine.com=0A=C2-=0A=C2-=0A=C2-=0Ael=no
follow target=_blank>http://www.matronics.com/Navigator?Zenith-List=0Aet
=_blank>http://forums.matronics.com=0Allow target=_blank>http://www.mat
ronics.com/contribution=0A=C2-=0A=C2-=0A=C2-=0A=C2-=0A=C2-=0Ahttp
://www.matronics.com/Navigator?Zenith-List=0A=C2-=0Ahttp://forums.matroni
cs.com=0A=C2-=0Ahttp://www.matronics.com/contribution=0A=C2-=0A=C2-
=0A=C2-=0A=C2-=0Ahttp://www.matronics.com/Navigator?Zenith-List=0Ahttp:
//forums.matronics.com=0Ahttp://www.matronics.com/contribution=0A=C2-=0A
=0A=0A__________ Information from ESET Smart Security, version of virus sig
nature database 6512 (20111003) __________=0A=0AThe message was checked by
ESET Smart Security.=0A=0A=0Ahttp:/ics.com
<http://www.matronics.com/Navigator?Zenith-List> " target=_blank p;
&nhttp://w======================= <http://www.matronics.com/contribution>
<http://www.matronics.com/contribution>
<http://www.matronics.com/contribution>
<http://www.matronics.com/contribution>
Email Forum -
Navigator to browse
List Un/Subscription,
7-Day Browse, Chat, FAQ,
http://www.matronics.com/Navigator?Zenith-List
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Zenith-List Digest: 7 Msgs - 10/03/11 |
Not quite, Steve - you need to go to *http://www.matronics.com/subscription
*
Carlos
On 4 October 2011 14:51, Steve Freeman <steve.freeman@syntaxds.com> wrote:
> If I remember correctly ' all you need to do is send an email to the li
st
> with UNSUBSCRIBE in the subject and the body of the email.****
>
> ** **
>
> List ' please correct me if am wrong.****
>
> ** **
>
> Steve****
>
> **
>
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Zenith-List Digest: 7 Msgs - 10/03/11 |
to unsubscribe go here:=C2-http://www.matronics.com/subscription/=C2- p
retty self explanatory from there.=0A=0ASorry to hear of William's passing.
=C2-Condolences to the family.=0A=C2-=0ABill Pag=C3=A1n=0A=0A=0A______
__________________________=0AFrom: Steve Freeman <steve.freeman@syntaxds.co
m>=0ATo: zenith-list@matronics.com=0ASent: Tuesday, October 4, 2011 2:51 PM
=0ASubject: RE: Zenith-List: Re: Zenith-List Digest: 7 Msgs - 10/03/11=0A
=0A=0AIf I remember correctly =93 all you need to do is send an email
to the list with UNSUBSCRIBE in the subject and the body of the email.=0A
=C2-=0AList =93 please correct me if am wrong.=0A=C2-=0ASteve=0A
=C2-=0AFrom:owner-zenith-list-server@matronics.com [mailto:owner-zenith-l
ist-server@matronics.com] On Behalf Of Bill Shirley Mitchell=0ASent: Tuesda
y, October 04, 2011 11:22 AM=0ATo: zenith-list@matronics.com=0ASubject: Zen
ith-List: Re: Zenith-List Digest: 7 Msgs - 10/03/11=0A=C2-=0AWilliam is d
eceased & we would like to retain this email but be deleted from these mail
ings. How do we go about doing that? =0AMitchell family=0A=0A______________
__________________=0A=0AFrom:Zenith-List Digest Server <zenith-list@matroni
cs.com>=0ATo: Zenith-List Digest List <zenith-list-digest@matronics.com>=0A
Sent: Tuesday, October 4, 2011 12:00 AM=0ASubject: Zenith-List Digest: 7 Ms
gs - 10/03/11=0A=0A*=0A=0A================
==========0A=C2- Online Versions of Today's List Digest
Archive=0A=====================
=====0A=0AToday's complete Zenith-List Digest can also be found in
either of the =0Atwo Web Links listed below.=C2- The .html file includes
the Digest formatted =0Ain HTML for viewing with a web browser and features
Hyperlinked Indexes =0Aand Message Navigation.=C2- The .txt file include
s the plain ASCII version =0Aof the Zenith-List Digest and can be viewed wi
th a generic text editor =0Asuch as Notepad or with a web browser. =0A=0AHT
ML Version:=0A=0A=C2- =C2- http://www.matronics.com/digest/digestview.p
hp?Style=82701&View=html&Chapter 11-10-03&Archive=Zenith=0A=0ATex
t Version:=0A=0A=C2- =C2- http://www.matronics.com/digest/digestview.ph
p?Style=82701&View=txt&Chapter 11-10-03&Archive=Zenith=0A=0A=0A
========================0A=C2
- EMail Version of Today's List Digest Archive=0A========
================0A=0A=0A=C2- =C2- =C2-
=C2- =C2- ----------------------------------------------------------=0A
=C2- =C2- =C2- =C2- =C2- =C2- =C2- =C2- =C2- =C2- =C2
- =C2- =C2- Zenith-List Digest Archive=0A=C2- =C2- =C2- =C2-
=C2- =C2- =C2- =C2- =C2- =C2- =C2- =C2- =C2- =C2- =C2
- =C2- =C2- =C2- =C2- ---=0A=C2- =C2- =C2- =C2- =C2-
=C2- =C2- =C2- =C2- =C2- Total Messages Posted Mon 10/03/11: 7=0A
=C2- =C2- =C2- =C2- =C2- ----------------------------------------
------------------=0A=0A=0AToday's Message Index:=0A----------------------
=0A=0A=C2- =C2- 1. 04:38 AM - 601 XL bearing bloc material=C2- (Miche
l Therrien)=0A=C2- =C2- 2. 05:09 AM - Re: 601 XL bearing bloc material
=C2- (Paul Mulwitz)=0A=C2- =C2- 3. 06:53 AM - Re: [Probable Spam] 601
XL bearing bloc material=C2- (Larry McFarland)=0A=C2- =C2- 4. 07:40
AM - Re: [Probable Spam] 601 XL bearing bloc material=C2- (Malcolm Hunt)
=0A=C2- =C2- 5. 09:31 AM - Re: [Probable Spam] 601 XL bearing bloc mate
rial=C2- (Michel Therrien)=0A=C2- =C2- 6. 10:26 AM - Re: [Probable Sp
am] 601 XL bearing bloc material=C2- (Larry McFarland)=0A=C2- =C2- 7.
08:26 PM - Re: [Probable Spam] 601 XL bearing bloc material=C2- (Michel
Therrien)=0A=0A=0A=0A________________________________=C2- Message 1=C2-
_____________________________________=0A=0A=0ATime: 04:38:17 AM PST US=0AF
rom: Michel Therrien <mtherr@yahoo.com>=0ASubject: Zenith-List: 601 XL bear
ing bloc material=0A=0AHello group,=0A=C2-=0AAs part orf my 601 renov
ation project, I want to re=0Aplace the lower nose wheel fork bearing with
the newer style 601 XL plastic=0Abloc.=C2- I would like to know what mate
rial is mandated (delrin, nylon,=0Aacetal, UHMWE?) and what is the thicknes
s.=0A=C2-=0AThanks!=0A=C2-=0AM=0Aichel=0A=C2-=0Ado not ar
chive=0A=0A----------------------------=0AMichel =0ATherrien CH601-HD
, C-GZGQ=0Ahttp://mthobby.pcperfect.com/ch601=0Ahttp://pag=0Aes.infinit
.net/mthobby=0A=0A=0A________________________________=0AFrom: Lar
=0Ary McFarland <larry@macsmachine.com>=0ATo: Zenith-List <zenith-list@ma
troni=0Acs.com>=0ASent: Wednesday, September 28, 2011 2:46:58 PM=0ASubj
ect: Zenith-=0AList: access panel drawing =0A=0A=0AHi guys,=0AI=9
9ve had a few peopl=0Ae ask about a drawing for the inspection panels I use
on my 601HDS. =0AThe =0Alink below will get you to the drawing on my sit
e and clicking the drawing =0Aat the bottom =0Aof the page will get you t
o a larger image that=99s =0Aprintable. The panels serve my plane well=
0Aand have never given any diffic=0Aulty. =C2-If you want to make a set o
f these, the drawing is =0Aa good gu=0Aide.=0A=C2-=0Ahttp://www.mac
smachine.com/html/winginsppanels.htm=0A=C2-=0A=0A=C2-=0AFly safe
guys,=0A=C2-=0ALarry McFarland=C2- 601HDS at www.m=0A====
================= =0A=0A_________________
_______________=C2- Message 2=C2- _____________________________________
=0A=0A=0ATime: 05:09:52 AM PST US=0AFrom: Paul Mulwitz <psm@att.net>=0ASubj
ect: Re: Zenith-List: 601 XL bearing bloc material=0A=0AHi Michael,=0A=0AI'
m not sure whether mine is the old or new stuff, but I think it is =0ANyloi
l -- oil impregnated nylon.=0A=0APaul=0AXL in flight test=0A=0AOn 10/3/2011
4:35 AM, Michel Therrien wrote:=0A> Hello group,=0A> As part orf my 601 re
novation project, I want to replace the lower =0A> nose wheel fork bearing
with the newer style 601 XL plastic bloc.=C2- I =0A> would like to know w
hat material is mandated (delrin, nylon, acetal, =0A> UHMWE?) and what is t
he thickness.=0A> Thanks!=0A> Michel=0A> do not archive=0A> ---------------
-------------=0A> Michel Therrien CH601-HD, C-GZGQ=0A> http://mthobby.pcper
fect.com/ch601=0A> http://pages.infinit.net/mthobby=0A> *From:* Larry McFar
land <larry@macsmachine.com>=0A> *To:* Zenith-List <zenith-list@matronics.c
om>=0A> *Sent:* Wednesday, September 28, 2011 2:46:58 PM=0A> *Subject:* Zen
ith-List: access panel drawing=0A>=0A> Hi guys,=0A> Ive had a few people as
k about a drawing for the inspection panels I =0A> use on my 601HDS.=0A> Th
e link below will get you to the drawing on my site and clicking the =0A> d
rawing at the bottom=0A> of the page will get you to a larger image thats p
rintable. The =0A> panels serve my plane well=0A> and have never given any
difficulty.=C2- If you want to make a set of =0A> these, the drawing is
=0A> a good guide.=0A> http://www.macsmachine.com/html/winginsppanels.htm
=0A> Fly safe guys,=0A> Larry McFarland=C2- 601HDS at www.macsmachine.com
=0A> <http://www.macsmachine.com/>=0A> *=0A>=0A> el=nofollow target=_b
lank>http://www.matronics.com/Navigator?Zenith-List=0A> et=_blank>http://
forums.matronics.com=0A> llow target=_blank>http://www.matronics.com/cont
ribution=0A>=0A> *=0A>=0A>=0A> *=0A>=0A>=0A> *=0A=0A_______________________
_________=C2- Message 3=C2- _____________________________________=0A=0A
=0ATime: 06:53:51 AM PST US=0AFrom: "Larry McFarland" <larry@macsmachine.co
m>=0ASubject: RE: [Probable Spam] Zenith-List: 601 XL bearing bloc material
=0A=0AHI Michel,=0A=0AI=99m using UHMWE at 3/8-inch thickness that replac
ed Nylon that =0Aabsorbed water.=C2- =0A=0ANot so expensive and easy to w
ork. =0A=0AReasonable Source:=C2- http://www.k-mac-plastics.net/index.htm
=0A=0A=0ALarry McFarland=C2- 601HDS at www.macsmachine.com=0A=0A=0AFrom:
owner-zenith-list-server@matronics.com =0A[mailto:owner-zenith-list-server
@matronics.com] On Behalf Of Michel =0ATherrien=0ASent: Monday, October 03,
2011 6:35 AM=0ASubject: [Probable Spam] Zenith-List: 601 XL bearing bloc m
aterial=0A=0A=0AHello group,=0A=0A=0AAs part orf my 601 renovation project,
I want to replace the lower nose =0Awheel fork bearing with the newer styl
e 601 XL plastic bloc.=C2- I would =0Alike to know what material is manda
ted (delrin, nylon, acetal, UHMWE?) =0Aand what is the thickness.=0A=0A=0AT
hanks!=0A=0A=0AMichel=0A=0A=0Ado not archive=0A=0A=0A----------------------
------=0AMichel Therrien CH601-HD, C-GZGQ=0Ahttp://mthobby.pcperfect.com/ch
601=0Ahttp://pages.infinit.net/mthobby=0A=0AFrom: Larry McFarland <larry@ma
csmachine.com>=0ASent: Wednesday, September 28, 2011 2:46:58 PM=0ASubject:
Zenith-List: access panel drawing =0A=0AHi guys,=0A=0AI=99ve had a few pe
ople ask about a drawing for the inspection =0Apanels I use on my 601HDS.
=0A=0AThe link below will get you to the drawing on my site and clicking th
e =0Adrawing at the bottom =0A=0Aof the page will get you to a larger image
that=99s printable. The =0Apanels serve my plane well=0A=0Aand have neve
r given any difficulty.=C2- If you want to make a set of =0Athese, the dr
awing is =0A=0Aa good guide.=0A=0A=0Ahttp://www.macsmachine.com/html/wingin
sppanels.htm=0A=0A=0AFly safe guys,=0A=0A=0ALarry McFarland=C2- 601HDS at
www.macsmachine.com =0A<http://www.macsmachine.com/> =0A=0A=0Ael=nofollo
w =0Atarget=_blank>http://www.matronics.com/Navigator?Zenith-List=0Aet=
_blank>http://forums.matronics.com=0Allow target=_blank>http://www.matron
ics.com/contribution=0A=0A=0A________________________________=C2- Message
4=C2- _____________________________________=0A=0A=0ATime: 07:40:30 AM PS
T US=0AFrom: "Malcolm Hunt" <malcolmhunt@mha1.fsbusiness.co.uk>=0ASubject:
RE: [Probable Spam] Zenith-List: 601 XL bearing bloc material=0A=0AHi Micha
el=0A=0A=0AThe plans call up Nyoil @ 1.5=9D thick, can be obtained in Eng
land =0Aso should be easy with you.=0A=0A=0ANylon is not the easiest to wor
k but the part from the factory is =0Aexpensive.=0A=0A=0AHope this helps=0A
=0A=0AMalcolm Hunt=0A=0APlans builder in England=0A=0A=0AFrom: owner-zenith
-list-server@matronics.com =0A[mailto:owner-zenith-list-server@matronics.co
m] On Behalf Of Larry =0AMcFarland=0ASent: 03 October 2011 14:51=0ASubject:
RE: [Probable Spam] Zenith-List: 601 XL bearing bloc material=0A=0A=0AHI M
ichel,=0A=0AI=99m using UHMWE at 3/8-inch thickness that replaced Nylon t
hat =0Aabsorbed water.=C2- =0A=0ANot so expensive and easy to work. =0A
=0AReasonable Source:=C2- http://www.k-mac-plastics.net/index.htm =0A=0A
=0ALarry McFarland=C2- 601HDS at www.macsmachine.com=0A=0A=0AFrom: owner-
zenith-list-server@matronics.com =0A[mailto:owner-zenith-list-server@matron
ics.com] On Behalf Of Michel =0ATherrien=0ASent: Monday, October 03, 2011 6
:35 AM=0ASubject: [Probable Spam] Zenith-List: 601 XL bearing bloc material
=0A=0A=0AHello group,=0A=0A=0AAs part orf my 601 renovation project, I want
to replace the lower nose =0Awheel fork bearing with the newer style 601 X
L plastic bloc.=C2- I would =0Alike to know what material is mandated (de
lrin, nylon, acetal, UHMWE?) =0Aand what is the thickness.=0A=0A=0AThanks!
=0A=0A=0AMichel=0A=0A=0Ado not archive=0A=0A=0A----------------------------
=0AMichel Therrien CH601-HD, C-GZGQ=0Ahttp://mthobby.pcperfect.com/ch601=0A
http://pages.infinit.net/mthobby=0A=0AFrom: Larry McFarland <larry@macsmach
ine.com>=0ASent: Wednesday, September 28, 2011 2:46:58 PM=0ASubject: Zenith
-List: access panel drawing =0A=0AHi guys,=0A=0AI=99ve had a few people a
sk about a drawing for the inspection =0Apanels I use on my 601HDS. =0A=0AT
he link below will get you to the drawing on my site and clicking the =0Adr
awing at the bottom =0A=0Aof the page will get you to a larger image that
=99s printable. The =0Apanels serve my plane well=0A=0Aand have never giv
en any difficulty.=C2- If you want to make a set of =0Athese, the drawing
is =0A=0Aa good guide.=0A=0A=0Ahttp://www.macsmachine.com/html/winginsppan
els.htm=0A=0A=0AFly safe guys,=0A=0A=0ALarry McFarland=C2- 601HDS at www.
macsmachine.com =0A<http://www.macsmachine.com/> =0A=0A=0Ael=nofollow =0A
target=_blank>http://www.matronics.com/Navigator?Zenith-List=0Aet=_blan
k>http://forums.matronics.com=0Allow target=_blank>http://www.matronics.c
om/contribution=0A=0A=0Ahttp://www.matronics.com/Navigator?Zenith-List=0A
=0Ahttp://forums.matronics.com=0A=0Ahttp://www.matronics.com/contribution
=0A=0A=0A__________ Information from ESET Smart Security, version of virus
=0Asignature database 6512 (20111003) __________=0A=0AThe message was check
ed by ESET Smart Security.=0A=0A=0A________________________________=C2- M
essage 5=C2- _____________________________________=0A=0A=0ATime: 09:31:00
AM PST US=0AFrom: Michel Therrien <mtherr@yahoo.com>=0ASubject: Re: [Proba
ble Spam] Zenith-List: 601 XL bearing bloc material=0A=0AI use 1/4 inch UHM
WE flush with the original 1/8" aluminum... i noticed tha=0At my gear leg g
ot a bit of wear (0.003") from movement over the=C2-6 year=0As that the p
lane flew (probably constant rudder movement).=C2- I would li=0Ake to do
away of the aluminum contact on the nose wheel... did you make it =0Aso tha
t contact is only on the plastic part?=C2- =0A=C2-=0AThanks!=0A
=0A=C2-=0AMichel=0A=C2-=0A=0A----------------------------=0AM
ichel Therrie=0An CH601-HD, C-GZGQ=0Ahttp://mthobby.pcperfect.com/ch601
=0Ahttp://pages.infi=0Anit.net/mthobby=0A=0A=0A____________________
____________=0AFrom: Larry McFa=0Arland <larry@macsmachine.com>=0ATo: z
enith-list@matronics.com=0ASent: Monda=0Ay, October 3, 2011 9:50:31 AM=
0ASubject: RE: [Probable Spam] Zenith-List: 6=0A01 XL bearing bloc material
=0A=0A=0AHI Michel,=0AI=99m using UHMWE at=0A3/8-inch thickness t
hat replaced Nylon that absorbed water.=C2- =0ANot s=0Ao expensive and
easy to work. =0AReasonable Source:=C2-=C2- http://www.=0Ak-mac-plast
ics.net/index.htm =0A=C2-=0A=C2-=0ALarry McFarland=C2- 601=0AHD
S at www.macsmachine.com=0A=C2-=0AFrom:owner-zenith-list-server@matro
ni=0Acs.com [mailto:owner-zenith-list-server@matronics.com] On Behalf Of Mi
chel =0ATherrien=0ASent: Monday, October 03, 2011 6:35 AM=0ATo: zenith-
list@matroni=0Acs.com=0ASubject: [Probable Spam] Zenith-List: 601 XL bear
ing bloc material=0A=0A=C2-=0AHello group,=0A=C2-=0AAs part orf
my 601 renovation project, =0AI want to replace the lower nose wheel fork
bearing with the newer style 60=0A1 XL plastic bloc.=C2- I would like to
know what material is mandated (de=0Alrin, nylon, acetal, UHMWE?) and what
is the thickness.=0A=C2-=0AThanks!=0A=0A=C2-=0AMichel=0A=C2
-=0Ado not archive=0A=C2-=0A-------------------=0A---------=0AMic
hel Therrien CH601-HD, C-GZGQ=0Ahttp://mthobby.pcperfect.com=0A/ch601=0
Ahttp://pages.infinit.net/mthobby=0AFrom:Larry McFarland <larry@mac=0Asma
chine.com>=0ATo: Zenith-List <zenith-list@matronics.com>=0ASent: Wednes
d=0Aay, September 28, 2011 2:46:58 PM=0ASubject: Zenith-List: access pane
l draw=0Aing =0AHi guys,=0AI=99ve had a few people ask about a drawin
g for the=0Ainspection panels I use on my 601HDS. =0AThe link below will
get you to th=0Ae drawing on my site and clicking the drawing at the bottom
=0Aof the page =0Awill get you to a larger image that=99s printable. T
he panels serve m=0Ay plane well=0Aand have never given any difficulty.
=C2-If you want to ma=0Ake a set of these, the drawing is =0Aa good gui
de.=0A=C2-=0Ahttp://www.ma=0Acsmachine.com/html/winginsppanels.htm=
0A=C2-=0A=C2-=0AFly safe guys,=0A=0A=C2-=0ALarry McFarland=
C2- 601HDS at www.macsmachine.com=0A=C2-=0A=C2=0A-=0A=C2-=0Ae
l=nofollow target=_blank>http://www.matronics.com/Navig=0Aator?Zenith-L
ist=0Aet=_blank>http://forums.matronics.com=0Allow target==0A_blank
>http://www.matronics.com/contribution=0A=C2-=0A=C2-=0A=C2-=0
A=0A=C2-=0Ahttp://www.matronics.com/Navigator?Zenith-List=0Ahttp://fo
rums.mat=0A======== =0A=0A________________________________
=C2- Message 6=C2- _____________________________________=0A=0A=0ATime:
10:26:12 AM PST US=0AFrom: "Larry McFarland" <larry@macsmachine.com>=0ASubj
ect: RE: [Probable Spam] Zenith-List: 601 XL bearing bloc material=0A=0AYes
Michel,=0A=0AI noticed wear in the same fore and aft areas and made adjust
ments to =0Akeep the tube =0A=0A>From being in contact with the aluminum. W
ith the UHMWE, that works =0Arather well.=0A=0AGet a good fit with the bear
ing plastic and then remove a little =0Aaluminum for clearance.=0A=0AIt=9
9ll hold.=0A=0A=0ALarry McFarland=C2- 601HDS at www.macsmachine.com=0A=0A
=0AFrom: owner-zenith-list-server@matronics.com =0A[mailto:owner-zenith-lis
t-server@matronics.com] On Behalf Of Michel =0ATherrien=0ASent: Monday, Oct
ober 03, 2011 11:28 AM=0ASubject: Re: [Probable Spam] Zenith-List: 601 XL b
earing bloc material=0A=0A=0AI use 1/4 inch UHMWE flush with the original 1
/8" aluminum... i noticed =0Athat my gear leg got a bit of wear (0.003") fr
om movement over the 6 =0Ayears that the plane flew (probably constant rudd
er movement).=C2- I would =0Alike to do away of the aluminum contact on t
he nose wheel... did you =0Amake it so that contact is only on the plastic
part?=C2- =0A=0A=0AThanks!=0A=0A=0AMichel=0A=0A=0A-----------------------
-----=0AMichel Therrien CH601-HD, C-GZGQ=0Ahttp://mthobby.pcperfect.com/ch6
01=0Ahttp://pages.infinit.net/mthobby=0A=0AFrom: Larry McFarland <larry@mac
smachine.com>=0ASent: Monday, October 3, 2011 9:50:31 AM=0ASubject: RE: [Pr
obable Spam] Zenith-List: 601 XL bearing bloc material=0A=0AHI Michel,=0A
=0AI=99m using UHMWE at 3/8-inch thickness that replaced Nylon that =0Aab
sorbed water.=C2- =0A=0ANot so expensive and easy to work. =0A=0AReasonab
le Source:=C2- http://www.k-mac-plastics.net/index.htm =0A=0A=0ALarry McF
arland=C2- 601HDS at www.macsmachine.com=0A=0A=0AFrom: owner-zenith-list-
server@matronics.com =0A[mailto:owner-zenith-list-server@matronics.com] On
Behalf Of Michel =0ATherrien=0ASent: Monday, October 03, 2011 6:35 AM=0ASub
ject: [Probable Spam] Zenith-List: 601 XL bearing bloc material=0A=0A=0AHel
lo group,=0A=0A=0AAs part orf my 601 renovation project, I want to replace
the lower nose =0Awheel fork bearing with the newer style 601 XL plastic bl
oc.=C2- I would =0Alike to know what material is mandated (delrin, nylon,
acetal, UHMWE?) =0Aand what is the thickness.=0A=0A=0AThanks!=0A=0A=0AMich
el=0A=0A=0Ado not archive=0A=0A=0A----------------------------=0AMichel The
rrien CH601-HD, C-GZGQ=0Ahttp://mthobby.pcperfect.com/ch601=0Ahttp://pages.
infinit.net/mthobby=0A=0AFrom: Larry McFarland <larry@macsmachine.com>=0ASe
nt: Wednesday, September 28, 2011 2:46:58 PM=0ASubject: Zenith-List: access
panel drawing =0A=0AHi guys,=0A=0AI=99ve had a few people ask about a dr
awing for the inspection =0Apanels I use on my 601HDS. =0A=0AThe link below
will get you to the drawing on my site and clicking the =0Adrawing at the
bottom =0A=0Aof the page will get you to a larger image that=99s printabl
e. The =0Apanels serve my plane well=0A=0Aand have never given any difficul
ty.=C2- If you want to make a set of =0Athese, the drawing is =0A=0Aa goo
d guide.=0A=0A=0Ahttp://www.macsmachine.com/html/winginsppanels.htm=0A=0A
=0AFly safe guys,=0A=0A=0ALarry McFarland=C2- 601HDS at www.macsmachine.c
om =0A<http://www.macsmachine.com/> =0A=0A=0Ael=nofollow =0Atarget=_bla
nk>http://www.matronics.com/Navigator?Zenith-List=0A=0Aet=_blank>http://f
orums.matronics.com <http://forums.matronics.com/> =0A=0Allow target=_bla
nk>http://www.matronics.com/contribution=0A=0A=0Ahttp://www.matronics.com/N
avigator?Zenith-List=0Ahttp://forums.matronics.com=0Ahttp://www.matronics.c
om/contribution=0A=0A=0Ael=nofollow =0Atarget=_blank>http://www.matroni
cs.com/Navigator?Zenith-List=0Aet=_blank>http://forums.matronics.com=0All
ow target=_blank>http://www.matronics.com/contribution=0A=0A=0A__________
______________________=C2- Message 7=C2- ______________________________
_______=0A=0A=0ATime: 08:26:16 PM PST US=0AFrom: Michel Therrien <mtherr@ya
hoo.com>=0ASubject: Re: [Probable Spam] Zenith-List: 601 XL bearing bloc ma
terial=0A=0AI noticed different varieties of Nyloil... there is the green o
ne and then,=0Athe MDX (gray or blue).=C2- Are they interchangeable?=C2
- It appears t=0Ahat the kit part is the grey Nyloil (that is filled with M
oly...).=0A=C2-=0A=0AMichel=0A=C2-=0A=0A---------------------
-------=0AMichel Therrien CH60=0A1-HD, C-GZGQ=0Ahttp://mthobby.pcperfec
t.com/ch601=0Ahttp://pages.infinit.ne=0At/mthobby=0A=0A=0A_________
_______________________=0AFrom: Malcolm Hunt <ma=0Alcolmhunt@mha1.fsbusin
ess.co.uk>=0ATo: zenith-list@matronics.com=0ASent: Mo=0Anday, October 3
, 2011 10:37:46 AM=0ASubject: RE: [Probable Spam] Zenith-Lis=0At: 601 XL
bearing bloc material=0A=0A=0AHi Michael=0A=C2-=0AThe plans cal
=0Al up Nyoil @ 1.5=9D thick, can be obtained in England so should be ea
=0Asy with you.=0A=C2-=0ANylon is not the easiest to work but the par
t from =0Athe factory is expensive.=0A=C2-=0AHope this helps=0A=C
2-=0AMalcolm Hun=0At=0APlans builder in England=0A=C2-=0AFrom:own
er-zenith-list-server@matro=0Anics.com [mailto:owner-zenith-list-server@mat
ronics.com] On Behalf Of Larry=0AMcFarland=0ASent: 03 October 2011 14:51
=0ATo: zenith-list@matronics.com=0A=0ASubject: RE: [Probable Spam] Zeni
th-List: 601 XL bearing bloc material=0A=0A=C2-=0AHI Michel,=0AI=
99m using UHMWE at 3/8-inch thickness that re=0Aplaced Nylon that absorbed
water.=C2- =0ANot so expensive and easy to wor=0Ak. =0AReasonable Sou
rce:=C2-=C2- http://www.k-mac-plastics.net/index.ht=0Am =0A=C2-=0
A=C2-=0ALarry McFarland=C2- 601HDS at www.macsmachine.com=0A=0A=C
2-=0AFrom:owner-zenith-list-server@matronics.com [mailto:owner-zenit=0Ah-
list-server@matronics.com] On Behalf Of Michel Therrien=0ASent: Monday, O
=0Actober 03, 2011 6:35 AM=0ATo: zenith-list@matronics.com=0ASubject: [
Probabl=0Ae Spam] Zenith-List: 601 XL bearing bloc material=0A=C2-=0A
Hello group,=0A=0A=C2-=0AAs part orf my 601 renovation project, I wan
t to replace the lo=0Awer nose wheel fork bearing with the newer style 601
XL plastic bloc.=C2-=0AI would like to know what material is mandated (de
lrin, nylon, acetal, UHM=0AWE?) and what is the thickness.=0A=C2-=0AT
hanks!=0A=C2-=0AMichel=0A=C2=0A-=0Ado not archive=0A=C2-=
0A----------------------------=0AMichel Therr=0Aien CH601-HD, C-GZGQ=0A
http://mthobby.pcperfect.com/ch601=0Ahttp://pages.in=0Afinit.net/mthobby
=0AFrom:Larry McFarland <larry@macsmachine.com>=0ATo: Zeni=0Ath-List <z
enith-list@matronics.com>=0ASent: Wednesday, September 28, 2011 2=0A:46:5
8 PM=0ASubject: Zenith-List: access panel drawing =0AHi guys,=0AI=0A
=99ve had a few people ask about a drawing for the inspection panels I u
=0Ase on my 601HDS. =0AThe link below will get you to the drawing on my s
ite a=0And clicking the drawing at the bottom =0Aof the page will get you
to a larg=0Aer image that=99s printable. The panels serve my plane well
=0Aand hav=0Ae never given any difficulty. =C2-If you want to make a se
t of these, the=0Adrawing is =0Aa good guide.=0A=C2-=0Ahttp://www.m
acsmachine.com/html/win=0Aginsppanels.htm=0A=C2-=0A=C2-=0AFly saf
e guys,=0A=C2-=0ALarry McFarla=0And=C2- 601HDS at www.macsmachine.c
om=0A=C2-=0A=C2-=0A=C2-=0Ael=no=0Afollow target=_blank>ht
tp://www.matronics.com/Navigator?Zenith-List=0Aet=0A=_blank>http://foru
ms.matronics.com=0Allow target=_blank>http://www.mat=0Aronics.com/contr
ibution=0A=C2-=0A=C2-=0A=C2-=0A=C2-=0A=C2-=0Ahttp=0A:
//www.matronics.com/Navigator?Zenith-List=0A=C2-=0Ahttp://forums.matr
oni=0Acs.com=0A=C2-=0Ahttp://www.matronics.com/contribution=0A=C2
-=0A=C2-=0A=0A=C2-=0A=C2-=0Ahttp://www.matronics.com/Navigato
r?Zenith-List=0Ahttp:=0A//forums.matronics.com=0Ahttp://www.matronics.c
om/contribution=0A=C2-=0A=0A=0A=0A__________ Information from ESE
T Smart Security, version of virus sig=0Anature database 6512 (20111003) __
________=0A=0AThe message was checked by =0AESET Smart Security.=0A
=0A=0Ahttp:/ics.com" target=_blank p; =C2- =C2- =C2- =C2- =C2
- =C2- =C2- =C2- =C2- =C2- &nhttp://w========
================0A=0A=0A=0A=0A=0A=0A=0A=0A=C2
-=0A=C2-=0Ahttp://www.matronics.com/Navigator?Zenith-List=0Ahttp://foru
==========
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|