---------------------------------------------------------- Zenith-List Digest Archive --- Total Messages Posted Fri 03/09/12: 4 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 06:02 AM - Re: Flutter testing (hallert) 2. 03:59 PM - Fuel probes (Steve Freeman) 3. 08:04 PM - Re: Fuel probes (wscribb) 4. 11:33 PM - Re: Re: Control Balance (Terry Phillips) ________________________________ Message 1 _____________________________________ Time: 06:02:14 AM PST US Subject: Zenith-List: Re: Flutter testing From: "hallert" Thanks guys. Got the flutter report. Anyone seen the 601 XLB/650 flight report? Read this topic online here: http://forums.matronics.com/viewtopic.php?p=368054#368054 ________________________________ Message 2 _____________________________________ Time: 03:59:54 PM PST US From: "Steve Freeman" Subject: Zenith-List: Fuel probes Will anyone advise on the best type of fuel probe to install in the 601/650 leading edge wing tanks? Any thoughts and guidance is very much appreciated. Steve ________________________________ Message 3 _____________________________________ Time: 08:04:54 PM PST US From: "wscribb" Subject: RE: Zenith-List: Fuel probes Steve, I'm going to install Stewart Warner 682-C this is the probe that has the Packard fitting on it. This installs in the top of the fuel tank, yet it clears the leading edge skin. Since these are a non stocking item at Stewart Warner I had to special order 4 of them and wait 6 weeks to receive them. These are the 240/30 Ohms sensors standard Ford gauge. Contact me off list if you would like more information. Bill From: owner-zenith-list-server@matronics.com [mailto:owner-zenith-list-server@matronics.com] On Behalf Of Steve Freeman Sent: Friday, March 09, 2012 3:59 PM Subject: Zenith-List: Fuel probes Will anyone advise on the best type of fuel probe to install in the 601/650 leading edge wing tanks? Any thoughts and guidance is very much appreciated. Steve ________________________________ Message 4 _____________________________________ Time: 11:33:10 PM PST US From: Terry Phillips Subject: Re: Zenith-List: Re: Control Balance Ron After 30 minutes perusing the Zenith Builder Area, I cannot find the info you posted. Can you post a link to the page where you found that information? Thanks Terry Ron Lendon wrote: > This is from the zenith builder area, it's the details of the change. > > 6W10 dateFeb 6, 2012 > Location of Aileron stops 6W104 change 130 to 150 > 6W101 Rev 1 Changed 85 to 48 (distance from pivot to aileron rod end bolt; to decrease aileron stick forces) > Adjusted the shape of the horn (no lightening hole). -- Terry Phillips ttp444~at~gmail.com Corvallis MT ZU-601XLB/Jab 3300 s .. l .. o .. o .. o .. w build kit - Tail & flaps are done; Upgrading wings & ailerons per the AMD Safety Directive http://www.mykitlog.com/N47TP/ ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message zenith-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Zenith-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/zenith-list Browse Digests http://www.matronics.com/digest/zenith-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.