Zenith-List Digest Sun 07/29/12

Zenith-List Digest Archive

Sun 07/29/12

Total Messages Posted: 3



Today's Message Index:
----------------------
 
     1. 08:51 AM - rivets vs UHMW (Carlos Sa)
     2. 09:10 AM - Re: rivets vs UHMW (Paul Mulwitz)
     3. 07:43 PM - Re: rivets vs UHMW (JohnDRead@aol.com)
 
 
 

Message 1


					INDEX  Back to Main INDEX
					NEXT  Skip to NEXT Message
	LIST  Reply to LIST Regarding this Message
		SENDER  Reply to SENDER Regarding this Message

      
      
Time: 08:51:00 AM PST US
From: Carlos Sa <carlossa52@gmail.com>
Subject: rivets vs UHMW      
      Hello, all
      
      When riveting UHMW to aluminum, on which side goes the rivet head?
      
      Thanks
      
      
      Carlos
      CH601-HD, plans
      

Message 2


					INDEX  Back to Main INDEX
				PREVIOUS  Skip to PREVIOUS Message
					NEXT  Skip to NEXT Message
	LIST  Reply to LIST Regarding this Message
		SENDER  Reply to SENDER Regarding this Message

      
      
Time: 09:10:14 AM PST US
From: Paul Mulwitz <psm@att.net>
Subject: Re: rivets vs UHMW      
      Hi Carlos,
      
      I don't think it matters which end of the rivet contacts UHMW. However, 
      that stuff is so soft you might need a metal washer between the rivet 
      head and the plastic.
      
      On my plane the only plastic used in structural places is nylon.
      
      Paul
      Camas, WA
      
      On 7/29/2012 8:47 AM, Carlos Sa wrote:
      > Hello, all
      >
      > When riveting UHMW to aluminum, on which side goes the rivet head?
      >
      > Thanks
      >
      >
      > Carlos
      > CH601-HD, plans
      > *
      >
      >
      > *
      
      

Message 3


					INDEX  Back to Main INDEX
				PREVIOUS  Skip to PREVIOUS Message
					NEXT  Skip to NEXT Message
	LIST  Reply to LIST Regarding this Message
		SENDER  Reply to SENDER Regarding this Message

      
      
Time: 07:43:41 PM PST US
From: JohnDRead@aol.com
Subject: Re: rivets vs UHMW      
      The head should be against the softer material.
      
      Regards,  John
      
      CH701 - Colorado - Jabiru 3300
      
      Cell: 719-494-4567
      Home:  303-648-3261  
      
      
      In a message dated 7/29/2012 9:51:31 A.M. Mountain Daylight Time,  
      carlossa52@gmail.com writes:
      
      Hello, all
      
      When riveting UHMW to aluminum, on which side goes  the rivet head?
      
      Thanks  
      
      
      Carlos
      CH601-HD,  plans
      
      (http://www.matronics.com/Navigator?Zenith-List) 
      (http://www.matronics.com/contribution) 
      
      








Other Matronics Email List Services




Post A New Message    zenith-list@matronics.com
UN/SUBSCRIBE    http://www.matronics.com/subscription
List FAQ    http://www.matronics.com/FAQ/Zenith-List.htm
Web Forum Interface To Lists    http://forums.matronics.com
Matronics List Wiki    http://wiki.matronics.com
7-Day List Browse    http://www.matronics.com/browse/zenith-list
Browse Zenith-List Digests    http://www.matronics.com/digest/zenith-list
Browse Other Lists    http://www.matronics.com/browse
Live Online Chat!    http://www.matronics.com/chat
Archive Downloading    http://www.matronics.com/archives
Photo Share    http://www.matronics.com/photoshare
Other Email Lists    http://www.matronics.com/emaillists
Contributions    http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --