----------------------------------------------------------
                           Zenith-List Digest Archive
                                      ---
                     Total Messages Posted Mon 10/29/12: 2
           ----------------------------------------------------------
 
 
Today's Message Index:
----------------------
 
     1. 07:09 PM - CH601-HD baggage floor  (Carlos Sa)
     2. 07:34 PM - Re: CH601-HD baggage floor  (Carlos Sa)
 
 
 
________________________________  Message 1  _____________________________________


Time: 07:09:21 PM PST US
From: Carlos Sa <carlossa52@gmail.com>
Subject: Zenith-List: CH601-HD baggage floor

Hello gang (assuming you are still out there...?)


I am doing a trial fitting of the (CH601-HD) baggage floor. So far,
everything fits nicely, rear fuse to centre wing, firewall, alignment, etc.

I am a bit puzzled by the baggage floor: it seems to be about 20 - 25 mm
(one inch or so) too long: according to the plans, the baggage floor should
end at the continuation of the seat's back (or 6F13-3, same thing).

Did any of the HD(S) builders out there have to trim the from edge of the
baggage floor?
I did a search of the archives, but did not find a similar case...
Actually, I found someone's post talking about a "perfect fit" (i.e., trim
required only to fit the longeron curve).

Comments/suggestions?

(PS: hope everyone is safe out there.)

Thanks


Carlos
CH601-HD, plans
rear fuse, centre wing, firewall in place

________________________________  Message 2  _____________________________________


Time: 07:34:57 PM PST US
From: Carlos Sa <carlossa52@gmail.com>
Subject: Re: Zenith-List: CH601-HD baggage floor

Here's a picture, might help explain the situation.

On 29 October 2012 22:07, Carlos Sa <carlossa52@gmail.com> wrote:

> Hello gang (assuming you are still out there...?)
>
>
> I am doing a trial fitting of the (CH601-HD) baggage floor. So far,
> everything fits nicely, rear fuse to centre wing, firewall, alignment, etc.
>
> I am a bit puzzled by the baggage floor: it seems to be about 20 - 25 mm
> (one inch or so) too long: according to the plans, the baggage floor should
> end at the continuation of the seat's back (or 6F13-3, same thing).
>
> Did any of the HD(S) builders out there have to trim the from edge of the
> baggage floor?
> I did a search of the archives, but did not find a similar case...
> Actually, I found someone's post talking about a "perfect fit" (i.e., trim
> required only to fit the longeron curve).
>
> Comments/suggestions?
>
> (PS: hope everyone is safe out there.)
>
> Thanks
>
>
> Carlos
> CH601-HD, plans
> rear fuse, centre wing, firewall in place
>
>
> *
>
> *
>
>

 

-------------------------------------------------------------------------------------
                       Other Matronics Email List Services
-------------------------------------------------------------------------------------
Post A New Message               zenith-list@matronics.com
UN/SUBSCRIBE                     http://www.matronics.com/subscription
List FAQ                         http://www.matronics.com/FAQ/Zenith-List.htm
Web Forum Interface To Lists     http://forums.matronics.com
Matronics List Wiki              http://wiki.matronics.com
Full Archive Search Engine       http://www.matronics.com/search
7-Day List Browse                http://www.matronics.com/browse/zenith-list
Browse Digests                   http://www.matronics.com/digest/zenith-list
Browse Other Lists               http://www.matronics.com/browse
Live Online Chat!                http://www.matronics.com/chat
Archive Downloading              http://www.matronics.com/archives
Photo Share                      http://www.matronics.com/photoshare
Other Email Lists                http://www.matronics.com/emaillists
Contributions                    http://www.matronics.com/contribution
-------------------------------------------------------------------------------------

These Email List Services are sponsored solely by Matronics and through the 
generous Contributions of its members.