Today's Message Index:
----------------------
1. 08:33 AM - Re: CH601-HD baggage floor (Jerry Latimer)
2. 08:50 AM - Re: CH601-HD baggage floor (Carlos Sa)
3. 09:06 AM - Re: CH601-HD baggage floor (Jerry Latimer)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | CH601-HD baggage floor |
Carlos,
I don't recall having to trim 6F13-3. I reviewed my building log and photos
from that time and there were no notes about having to trim 25mm from the
front edge.
Jerry
_____
From: owner-zenith-list-server@matronics.com
[mailto:owner-zenith-list-server@matronics.com] On Behalf Of Carlos Sa
Sent: Monday, October 29, 2012 7:08 PM
Subject: Zenith-List: CH601-HD baggage floor
Hello gang (assuming you are still out there...?)
I am doing a trial fitting of the (CH601-HD) baggage floor. So far,
everything fits nicely, rear fuse to centre wing, firewall, alignment, etc.
I am a bit puzzled by the baggage floor: it seems to be about 20 - 25 mm
(one inch or so) too long: according to the plans, the baggage floor should
end at the continuation of the seat's back (or 6F13-3, same thing).
Did any of the HD(S) builders out there have to trim the from edge of the
baggage floor?
I did a search of the archives, but did not find a similar case...
Actually, I found someone's post talking about a "perfect fit" (i.e., trim
required only to fit the longeron curve).
Comments/suggestions?
(PS: hope everyone is safe out there.)
Thanks
Carlos
CH601-HD, plans
rear fuse, centre wing, firewall in place
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: CH601-HD baggage floor |
Thanks, Jerry - It seems I am in a unusual situation.
Maybe the seat back angle is off... I sent a note to ZAC, as this could be
a symptom of some major issue...
Carlos
On 30 October 2012 11:32, Jerry Latimer <jlatimer1@cox.net> wrote:
> **
> Carlos,
>
> I don't recall having to trim 6F13-3. I reviewed my building log and
> photos from that time and there were no notes about having to trim 25mm
> from the front edge.
>
> Jerry
>
> ------------------------------
> *From:* owner-zenith-list-server@matronics.com [mailto:
> owner-zenith-list-server@matronics.com] *On Behalf Of *Carlos Sa
> *Sent:* Monday, October 29, 2012 7:08 PM
> *To:* zenith-list@matronics.com
> *Subject:* Zenith-List: CH601-HD baggage floor
>
> Hello gang (assuming you are still out there...?)
>
>
> I am doing a trial fitting of the (CH601-HD) baggage floor. So far,
> everything fits nicely, rear fuse to centre wing, firewall, alignment, etc.
>
> I am a bit puzzled by the baggage floor: it seems to be about 20 - 25 mm
> (one inch or so) too long: according to the plans, the baggage floor should
> end at the continuation of the seat's back (or 6F13-3, same thing).
>
> Did any of the HD(S) builders out there have to trim the from edge of the
> baggage floor?
> I did a search of the archives, but did not find a similar case...
> Actually, I found someone's post talking about a "perfect fit" (i.e., trim
> required only to fit the longeron curve).
>
> Comments/suggestions?
>
> (PS: hope everyone is safe out there.)
>
> Thanks
>
>
> Carlos
> CH601-HD, plans
> rear fuse, centre wing, firewall in place
>
> *
>
> *
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | CH601-HD baggage floor |
Carlos,
When I go to the airport next, I will measure the baggage floor and see if
I've removed some material from it. I know I had to make some modifications
to rear turtle deck when I installed the front opening canopy, but I don't
think I had to trim the baggage floor.
Jerry
_____
From: owner-zenith-list-server@matronics.com
[mailto:owner-zenith-list-server@matronics.com] On Behalf Of Carlos Sa
Sent: Tuesday, October 30, 2012 8:49 AM
Subject: Re: Zenith-List: CH601-HD baggage floor
Thanks, Jerry - It seems I am in a unusual situation.
Maybe the seat back angle is off... I sent a note to ZAC, as this could be a
symptom of some major issue...
Carlos
On 30 October 2012 11:32, Jerry Latimer <jlatimer1@cox.net> wrote:
Carlos,
I don't recall having to trim 6F13-3. I reviewed my building log and photos
from that time and there were no notes about having to trim 25mm from the
front edge.
Jerry
_____
From: owner-zenith-list-server@matronics.com
[mailto:owner-zenith-list-server@matronics.com] On Behalf Of Carlos Sa
Sent: Monday, October 29, 2012 7:08 PM
Subject: Zenith-List: CH601-HD baggage floor
Hello gang (assuming you are still out there...?)
I am doing a trial fitting of the (CH601-HD) baggage floor. So far,
everything fits nicely, rear fuse to centre wing, firewall, alignment, etc.
I am a bit puzzled by the baggage floor: it seems to be about 20 - 25 mm
(one inch or so) too long: according to the plans, the baggage floor should
end at the continuation of the seat's back (or 6F13-3, same thing).
Did any of the HD(S) builders out there have to trim the from edge of the
baggage floor?
I did a search of the archives, but did not find a similar case...
Actually, I found someone's post talking about a "perfect fit" (i.e., trim
required only to fit the longeron curve).
Comments/suggestions?
(PS: hope everyone is safe out there.)
Thanks
Carlos
CH601-HD, plans
rear fuse, centre wing, firewall in place
arget="_blank">http://www.matronics.com/Navigator?Zenith-List
tp://forums.matronics.com
_blank">http://www.matronics.com/contribution
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|