---------------------------------------------------------- Zenith-List Digest Archive --- Total Messages Posted Tue 10/30/12: 3 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 08:33 AM - Re: CH601-HD baggage floor (Jerry Latimer) 2. 08:50 AM - Re: CH601-HD baggage floor (Carlos Sa) 3. 09:06 AM - Re: CH601-HD baggage floor (Jerry Latimer) ________________________________ Message 1 _____________________________________ Time: 08:33:27 AM PST US From: "Jerry Latimer" Subject: RE: Zenith-List: CH601-HD baggage floor Carlos, I don't recall having to trim 6F13-3. I reviewed my building log and photos from that time and there were no notes about having to trim 25mm from the front edge. Jerry _____ From: owner-zenith-list-server@matronics.com [mailto:owner-zenith-list-server@matronics.com] On Behalf Of Carlos Sa Sent: Monday, October 29, 2012 7:08 PM Subject: Zenith-List: CH601-HD baggage floor Hello gang (assuming you are still out there...?) I am doing a trial fitting of the (CH601-HD) baggage floor. So far, everything fits nicely, rear fuse to centre wing, firewall, alignment, etc. I am a bit puzzled by the baggage floor: it seems to be about 20 - 25 mm (one inch or so) too long: according to the plans, the baggage floor should end at the continuation of the seat's back (or 6F13-3, same thing). Did any of the HD(S) builders out there have to trim the from edge of the baggage floor? I did a search of the archives, but did not find a similar case... Actually, I found someone's post talking about a "perfect fit" (i.e., trim required only to fit the longeron curve). Comments/suggestions? (PS: hope everyone is safe out there.) Thanks Carlos CH601-HD, plans rear fuse, centre wing, firewall in place ________________________________ Message 2 _____________________________________ Time: 08:50:23 AM PST US From: Carlos Sa Subject: Re: Zenith-List: CH601-HD baggage floor Thanks, Jerry - It seems I am in a unusual situation. Maybe the seat back angle is off... I sent a note to ZAC, as this could be a symptom of some major issue... Carlos On 30 October 2012 11:32, Jerry Latimer wrote: > ** > Carlos, > > I don't recall having to trim 6F13-3. I reviewed my building log and > photos from that time and there were no notes about having to trim 25mm > from the front edge. > > Jerry > > ------------------------------ > *From:* owner-zenith-list-server@matronics.com [mailto: > owner-zenith-list-server@matronics.com] *On Behalf Of *Carlos Sa > *Sent:* Monday, October 29, 2012 7:08 PM > *To:* zenith-list@matronics.com > *Subject:* Zenith-List: CH601-HD baggage floor > > Hello gang (assuming you are still out there...?) > > > I am doing a trial fitting of the (CH601-HD) baggage floor. So far, > everything fits nicely, rear fuse to centre wing, firewall, alignment, etc. > > I am a bit puzzled by the baggage floor: it seems to be about 20 - 25 mm > (one inch or so) too long: according to the plans, the baggage floor should > end at the continuation of the seat's back (or 6F13-3, same thing). > > Did any of the HD(S) builders out there have to trim the from edge of the > baggage floor? > I did a search of the archives, but did not find a similar case... > Actually, I found someone's post talking about a "perfect fit" (i.e., trim > required only to fit the longeron curve). > > Comments/suggestions? > > (PS: hope everyone is safe out there.) > > Thanks > > > Carlos > CH601-HD, plans > rear fuse, centre wing, firewall in place > > * > > * > > ________________________________ Message 3 _____________________________________ Time: 09:06:59 AM PST US From: "Jerry Latimer" Subject: RE: Zenith-List: CH601-HD baggage floor Carlos, When I go to the airport next, I will measure the baggage floor and see if I've removed some material from it. I know I had to make some modifications to rear turtle deck when I installed the front opening canopy, but I don't think I had to trim the baggage floor. Jerry _____ From: owner-zenith-list-server@matronics.com [mailto:owner-zenith-list-server@matronics.com] On Behalf Of Carlos Sa Sent: Tuesday, October 30, 2012 8:49 AM Subject: Re: Zenith-List: CH601-HD baggage floor Thanks, Jerry - It seems I am in a unusual situation. Maybe the seat back angle is off... I sent a note to ZAC, as this could be a symptom of some major issue... Carlos On 30 October 2012 11:32, Jerry Latimer wrote: Carlos, I don't recall having to trim 6F13-3. I reviewed my building log and photos from that time and there were no notes about having to trim 25mm from the front edge. Jerry _____ From: owner-zenith-list-server@matronics.com [mailto:owner-zenith-list-server@matronics.com] On Behalf Of Carlos Sa Sent: Monday, October 29, 2012 7:08 PM Subject: Zenith-List: CH601-HD baggage floor Hello gang (assuming you are still out there...?) I am doing a trial fitting of the (CH601-HD) baggage floor. So far, everything fits nicely, rear fuse to centre wing, firewall, alignment, etc. I am a bit puzzled by the baggage floor: it seems to be about 20 - 25 mm (one inch or so) too long: according to the plans, the baggage floor should end at the continuation of the seat's back (or 6F13-3, same thing). Did any of the HD(S) builders out there have to trim the from edge of the baggage floor? I did a search of the archives, but did not find a similar case... Actually, I found someone's post talking about a "perfect fit" (i.e., trim required only to fit the longeron curve). Comments/suggestions? (PS: hope everyone is safe out there.) Thanks Carlos CH601-HD, plans rear fuse, centre wing, firewall in place arget="_blank">http://www.matronics.com/Navigator?Zenith-List tp://forums.matronics.com _blank">http://www.matronics.com/contribution ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message zenith-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Zenith-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/zenith-list Browse Digests http://www.matronics.com/digest/zenith-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.