Zenith601-List Digest Archive

Sat 06/21/08


Total Messages Posted: 6



Today's Message Index:
----------------------
 
     1. 07:42 AM - BRS engine mount firewall attachment drawing? (Debo Cox)
     2. 09:35 AM - Re: BRS engine mount firewall attachment drawing? (Iberplanes IGL)
     3. 10:08 AM - Re: BRS engine mount firewall attachment drawing? (Craig Payne)
     4. 10:35 AM - Re: BRS engine mount firewall attachment drawing? (Debo Cox)
     5. 10:46 AM - Rear starter update  (Aerolitellc@aol.com)
     6. 10:54 AM - Re: BRS engine mount firewall attachment drawing? (Craig Payne)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 07:42:14 AM PST US
    From: Debo Cox <sky_ranger161@yahoo.com>
    Subject: BRS engine mount firewall attachment drawing?
    Hi guys, I'm at the point of attaching my new-style BRS engine mount brackets to the firewall. Has anyone seen a drawing that specifies number, type, and placement of bolts, etc? I searched the archives and the BRS site - no luck with the new Zenith mounts. I'll check with Zenith if there's not one out there and post it here. Thanks in advance. Debo Cox Nags Head, NC Scratchbuilding XL/Corvair www.mykitlog.com/debo do not archive


    Message 2


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 09:35:00 AM PST US
    From: "Iberplanes IGL" <iberplanes@gmail.com>
    Subject: Re: BRS engine mount firewall attachment drawing?
    Hi there, I only have the installation manuals for the one that ZAC recommends. Whats=B4the difference with this new one? Any website to check it out? Thanks , Alberto Martin www.iberplanes.es Igualada - Barcelona - Spain ---------------------------------------------- Zodiac 601 XL Builder Serial: 6-7011 Tail Kit: Finished Wings: Not Started Fuselage: Ordered Engine: Jabiru 3300 comming home!!


    Message 3


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 10:08:32 AM PST US
    From: "Craig Payne" <craig@craigandjean.com>
    Subject: BRS engine mount firewall attachment drawing?
    The revised 6B6 dated 8/7 shows the details of the triangular top motor mount bracket. I've attached the copy Caleb at ZAC sent me. -- Craig -----Original Message----- From: owner-zenith601-list-server@matronics.com [mailto:owner-zenith601-list-server@matronics.com] On Behalf Of Debo Cox Sent: Saturday, June 21, 2008 8:42 AM Subject: Zenith601-List: BRS engine mount firewall attachment drawing? Hi guys, I'm at the point of attaching my new-style BRS engine mount brackets to the firewall. Has anyone seen a drawing that specifies number, type, and placement of bolts, etc? I searched the archives and the BRS site - no luck with the new Zenith mounts. I'll check with Zenith if there's not one out there and post it here. Thanks in advance. Debo Cox Nags Head, NC Scratchbuilding XL/Corvair www.mykitlog.com/debo do not archive


    Message 4


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 10:35:27 AM PST US
    From: Debo Cox <sky_ranger161@yahoo.com>
    Subject: BRS engine mount firewall attachment drawing?
    Craig! This is perfect. Exactly what I was looking for. Thanks very much. This is why I stay on this list. You da man. Debo Cox Nags Head, NC Scratchbuilding XL/Corvair www.mykitlog.com/debo do not archive --- On Sat, 6/21/08, Craig Payne <craig@craigandjean.com> wrote: > From: Craig Payne <craig@craigandjean.com> > Subject: RE: Zenith601-List: BRS engine mount firewall attachment drawing? > To: zenith601-list@matronics.com > Date: Saturday, June 21, 2008, 1:08 PM > The revised 6B6 dated 8/7 shows the details of the > triangular top motor > mount bracket. I've attached the copy Caleb at ZAC sent > me. > > -- Craig > > -----Original Message----- > From: owner-zenith601-list-server@matronics.com > [mailto:owner-zenith601-list-server@matronics.com] On > Behalf Of Debo Cox > Sent: Saturday, June 21, 2008 8:42 AM > To: zenith-list@matronics.com; zenith601-list@matronics.com > Subject: Zenith601-List: BRS engine mount firewall > attachment drawing? > > <sky_ranger161@yahoo.com> > > Hi guys, > > I'm at the point of attaching my new-style BRS engine > mount brackets to the > firewall. Has anyone seen a drawing that specifies number, > type, and > placement of bolts, etc? I searched the archives and the > BRS site - no luck > with the new Zenith mounts. I'll check with Zenith if > there's not one out > there and post it here. > > Thanks in advance. > > Debo Cox > Nags Head, NC > Scratchbuilding XL/Corvair > www.mykitlog.com/debo > > do not archive


    Message 5


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 10:46:24 AM PST US
    From: Aerolitellc@aol.com
    Subject: Rear starter update
    List We have just finished a 10 hour flight from Englewood Fl. to Louisville KY with the new rear starter setup and you can view pics and a video of the engine run up at Bill Clapp's place on the web site here _http://www.aeroliteproducts.com/Rear_Starter_Kit.php_ (http://www.aeroliteproducts.com/Rear_Starter_Kit.php) We plan to have the airplane at Oshkosh with the new rear starter setup. I will be updating the site with a Technical update on distributors as well as more ring gear cracks in the next few hours. Jeff _www.aeroliteproducts.com_ (http://www.aeroliteproducts.com) **************Gas prices getting you down? Search AOL Autos for fuel-efficient used cars. (http://autos.aol.com/used?ncid=aolaut00050000000007)


    Message 6


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 10:54:33 AM PST US
    From: "Craig Payne" <craig@craigandjean.com>
    Subject: BRS engine mount firewall attachment drawing?
    I hope the horizontal angle of the firewall to the upper longeron matches that of the bracket. Otherwise you will have to trim the bracket like I did. Or maybe you welded your own. Also be careful to stagger the bolts through the bracket and the longeron relative to the rivets that hold the side skins to the longerons. Otherwise you may find it difficult to get the nuts and washers on the bolts (and get a socket on them) due to interference with the "bulge" of the pulled rivets inside the fuselage. But my installation was probably more complex than yours since I was retrofitting the new style mounts dues to manufacturing mistakes in my QBK. -- Craig -----Original Message----- From: owner-zenith601-list-server@matronics.com [mailto:owner-zenith601-list-server@matronics.com] On Behalf Of Debo Cox Sent: Saturday, June 21, 2008 11:34 AM Subject: RE: Zenith601-List: BRS engine mount firewall attachment drawing? Craig! This is perfect. Exactly what I was looking for. Thanks very much. This is why I stay on this list. You da man. Debo Cox Nags Head, NC Scratchbuilding XL/Corvair www.mykitlog.com/debo do not archive --- On Sat, 6/21/08, Craig Payne <craig@craigandjean.com> wrote: > From: Craig Payne <craig@craigandjean.com> > Subject: RE: Zenith601-List: BRS engine mount firewall attachment drawing? > To: zenith601-list@matronics.com > Date: Saturday, June 21, 2008, 1:08 PM > The revised 6B6 dated 8/7 shows the details of the > triangular top motor > mount bracket. I've attached the copy Caleb at ZAC sent > me. > > -- Craig > > -----Original Message----- > From: owner-zenith601-list-server@matronics.com > [mailto:owner-zenith601-list-server@matronics.com] On > Behalf Of Debo Cox > Sent: Saturday, June 21, 2008 8:42 AM > To: zenith-list@matronics.com; zenith601-list@matronics.com > Subject: Zenith601-List: BRS engine mount firewall > attachment drawing? > > <sky_ranger161@yahoo.com> > > Hi guys, > > I'm at the point of attaching my new-style BRS engine > mount brackets to the > firewall. Has anyone seen a drawing that specifies number, > type, and > placement of bolts, etc? I searched the archives and the > BRS site - no luck > with the new Zenith mounts. I'll check with Zenith if > there's not one out > there and post it here. > > Thanks in advance. > > Debo Cox > Nags Head, NC > Scratchbuilding XL/Corvair > www.mykitlog.com/debo > > do not archive




    Other Matronics Email List Services

  • Post A New Message
  •   zenith601-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/Zenith601-List.htm
  • Web Forum Interface To Lists
  •   http://forums.matronics.com
  • Matronics List Wiki
  •   http://wiki.matronics.com
  • 7-Day List Browse
  •   http://www.matronics.com/browse/zenith601-list
  • Browse Zenith601-List Digests
  •   http://www.matronics.com/digest/zenith601-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contribution

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --