Today's Message Index:
----------------------
1. 02:53 AM - Oshkosh (Aerolitellc@aol.com)
2. 06:24 AM - Re: stabilizer skin alignment (Scott E Bevier)
3. 03:38 PM - Re: stabilizer skin alignment (Danny Offill)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
If anyone is interested I have the new rear system and a Corvair flight
engine here at Oshkosh. It is at my campsite so if you want to see them just give
me a call and I will meet you and be glad to show them to you.
Jeff
502-644-8123
_www.aeroliteproducts.com_ (http://www.aeroliteproducts.com)
**************Looking for a car that's sporty, fun and fits in your budget?
Read reviews on AOL Autos.
(http://autos.aol.com/cars-BMW-128-2008/expert-review?ncid=aolaut00050000000017 )
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | stabilizer skin alignment |
Danny,
Try making some shims from 0.040 6061-T6. My spars were also bowed slightly
as you described.
I inserted a picture below. If you can't see it, try viewing the email as
HTML, or email me off list and I can send you the file.
The two parts in the center of the picture are the attachment doublers, not
shims.
Scott
Ke4hrh@comcast.net
DSC00001.JPG
-----Original Message-----
From: owner-zenith601-list-server@matronics.com
[mailto:owner-zenith601-list-server@matronics.com] On Behalf Of Danny Offill
Sent: Sunday, August 03, 2008 12:15 AM
Subject: RE: Zenith601-List: stabilizer skin alignment
I'm at the same point and have the same question.
Not sure how to move on.
Danny
-----Original Message-----
From: owner-zenith601-list-server@matronics.com
[mailto:owner-zenith601-list-server@matronics.com] On Behalf Of rcarsey1
Sent: Saturday, August 02, 2008 9:58 PM
Subject: Zenith601-List: stabilizer skin alignment
<rcarsey+zenith@monmouth.edu>
So I am at that point where i'm attempting to fit my pre-drilled skin to the
skeleton ( front/rear spar and 6 ribs)...
I'm basically having trouble lining up all the holes. I did find that
towards the outside of the stabilizer, the two spars are drawn in, closer to
each other (by about 4mm or so if i remember correctly) -- due to ribs 1 & 6
not having a spar doubler underneath it.
I have followed the directions closely -- there is no shim to go underneath
these ribs.. how have you dealt with this? when looking at the edge of the
skin laying on the skeleton, its clear that the spar bows outwards in the
center. do i straighten out the spar somehow? how? or do i just like up
the two holes at either end of the spar.. clamp.. and start drilling?
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=196228#196228
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | stabilizer skin alignment |
Thanks Scott, I'll give that a try.
Danny
From: owner-zenith601-list-server@matronics.com
[mailto:owner-zenith601-list-server@matronics.com] On Behalf Of Scott E
Bevier
Sent: Sunday, August 03, 2008 8:24 AM
Subject: RE: Zenith601-List: stabilizer skin alignment
Danny,
Try making some shims from 0.040 6061-T6. My spars were also bowed slightly
as you described.
I inserted a picture below. If you can't see it, try viewing the email as
HTML, or email me off list and I can send you the file.
The two parts in the center of the picture are the attachment doublers, not
shims.
Scott
Ke4hrh@comcast.net
DSC00001.JPG
-----Original Message-----
From: owner-zenith601-list-server@matronics.com
[mailto:owner-zenith601-list-server@matronics.com] On Behalf Of Danny Offill
Sent: Sunday, August 03, 2008 12:15 AM
Subject: RE: Zenith601-List: stabilizer skin alignment
I'm at the same point and have the same question.
Not sure how to move on.
Danny
-----Original Message-----
From: owner-zenith601-list-server@matronics.com
[mailto:owner-zenith601-list-server@matronics.com] On Behalf Of rcarsey1
Sent: Saturday, August 02, 2008 9:58 PM
Subject: Zenith601-List: stabilizer skin alignment
<rcarsey+zenith@monmouth.edu>
So I am at that point where i'm attempting to fit my pre-drilled skin to the
skeleton ( front/rear spar and 6 ribs)...
I'm basically having trouble lining up all the holes. I did find that
towards the outside of the stabilizer, the two spars are drawn in, closer to
each other (by about 4mm or so if i remember correctly) -- due to ribs 1 & 6
not having a spar doubler underneath it.
I have followed the directions closely -- there is no shim to go underneath
these ribs.. how have you dealt with this? when looking at the edge of the
skin laying on the skeleton, its clear that the spar bows outwards in the
center. do i straighten out the spar somehow? how? or do i just like up
the two holes at either end of the spar.. clamp.. and start drilling?
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=196228#196228
style='mso-spacerun:yes'> - The Zenith601-List Email Forum -
to browse
Un/Subscription,
Browse, Chat, FAQ,
more:
style='mso-spacerun:yes'> -->
http://www.matronics.com/Navigator?Zenith601-List
style='mso-spacerun:yes'> - MATRONICS WEB FORUMS -
Web Forums!
style='mso-spacerun:yes'> --> http://forums.matronics.com
style='mso-spacerun:yes'> - List Contribution Web Site -
Thank you for your generous support!
style='mso-spacerun:yes'> -Matt Dralle, List
Admin.
style='mso-spacerun:yes'> --> http://www.matronics.com/contribution
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|