---------------------------------------------------------- Zenith601-List Digest Archive --- Total Messages Posted Sat 11/15/08: 5 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 05:26 AM - Re: Zenith-List: 601XL - Aileron Trim Tab Deflection (Juan Vega) 2. 05:36 AM - Re: All 601XL grounded in Netherlands (aerobat) 3. 08:14 AM - Re: Re: All 601XL grounded in Netherlands (Craig Payne) 4. 10:39 AM - Re: All 601XL grounded in Netherlands (Gig Giacona) 5. 08:35 PM - Re: All 601XL grounded in Netherlands (chris Sinfield) ________________________________ Message 1 _____________________________________ Time: 05:26:37 AM PST US From: Juan Vega Subject: Zenith601-List: Re: Zenith-List: 601XL - Aileron Trim Tab Deflection make another horn and put the hole closer in. Juan -----Original Message----- >From: Dave VanLanen >Sent: Nov 14, 2008 11:28 PM >To: zenith601-list@matronics.com, zenith-list@matronics.com >Subject: Zenith-List: 601XL - Aileron Trim Tab Deflection > >I just finished installing my aileron trim, and when I tested it, I can only >get a total of 40 degrees of deflection. According to the plans, I should >be able to get 50 degrees of deflection (25 up and 25 down). Adjusting the >length of the control rod only changes the distribution of the 40 degrees >between up and down - it does not increase the total deflection. I checked >that the servo was working correctly, which it was (.7" travel per specs). >I also checked that there was no binding of the control rod clevis with the >trim tab horn angle. The only thing I could find was that the center of the >control rod mounting hole in the horn angle was 13 mm up from the flange >instead of the 12 mm specified in the plans. I find it hard to believe that >1 mm would cause a 10 degree loss in deflection. >Has anyone else experienced this problem, and if so, what did you do to >resolve? > >Thanks, >Dave Van Lanen >601XL - tail done, flaps done, working on ailerons ________________________________ Message 2 _____________________________________ Time: 05:36:27 AM PST US Subject: Zenith601-List: Re: All 601XL grounded in Netherlands From: "aerobat" The aircraft is grounded by most European countries now, here in the UK about two dozen are affected. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=214340#214340 ________________________________ Message 3 _____________________________________ Time: 08:14:01 AM PST US From: "Craig Payne" Subject: RE: Zenith601-List: Re: All 601XL grounded in Netherlands As I understand it the XL was grounded in the UK due to worries about the cable AD, not the Dutch action. What will the UK authorities do to decide whether to let them fly again? -- Craig Do not archive -----Original Message----- From: owner-zenith601-list-server@matronics.com [mailto:owner-zenith601-list-server@matronics.com] On Behalf Of aerobat Sent: Saturday, November 15, 2008 6:36 AM Subject: Zenith601-List: Re: All 601XL grounded in Netherlands The aircraft is grounded by most European countries now, here in the UK about two dozen are affected. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=214340#214340 ________________________________ Message 4 _____________________________________ Time: 10:39:31 AM PST US Subject: Zenith601-List: Re: All 601XL grounded in Netherlands From: "Gig Giacona" David, I curious. Did they call you because you had a CZAW built aircraft? -------- W.R. "Gig" Giacona 601XL Under Construction See my progress at www.peoamerica.net/N601WR Read this topic online here: http://forums.matronics.com/viewtopic.php?p=214373#214373 ________________________________ Message 5 _____________________________________ Time: 08:35:25 PM PST US Subject: Zenith601-List: Re: All 601XL grounded in Netherlands From: "chris Sinfield" Some good news in Australia the RAA has not grounded any XL's there is 1imported CZAW built aircraft and the rest are by zenith kits. We have a good Zenith XL network and he was notified of the aileron tension issues and checked his A/C. yes his cables were about 1/2 of what they should be. of note he had no flutter issues before with the lower tensions. The RAA here are happy with us having the SB in our XL newsletter, the remainder of us are all builders of XL those finished and those still going. we built it we should know how to check it, maintain it. Common sense to the RAA. Chris. Sydney XL Jab3300 Read this topic online here: http://forums.matronics.com/viewtopic.php?p=214435#214435 ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message zenith601-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Zenith601-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/zenith601-list Browse Digests http://www.matronics.com/digest/zenith601-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.