Zenith601-List Digest Archive

Sun 01/04/09


Total Messages Posted: 4



Today's Message Index:
----------------------
 
     1. 10:38 AM - Re: W&B envelope CH601XL (rans6andrew)
     2. 11:09 AM - Elevator bias spring (jaybannist@cs.com)
     3. 12:36 PM - Re: Elevator bias spring (David Johnson)
     4. 01:39 PM - Re: Elevator bias spring (jaybannist@cs.com)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 10:38:09 AM PST US
    Subject: Re: W&B envelope CH601XL
    From: "rans6andrew" <andrewcattell@hotmail.com>
    The LAA, who usually go OTT with approvals and testing, publish a document called a TAD for all amateur built aircraft. This document has some useful info regarding weights, CoG limits, operating speeds etc. Generally the info within the TAD will have been checked by a thorough flight test program performed on the first completed example of the type to be completed. For the 601XL see http://www.lightaircraftassociation.co.uk/engineering/TADs/162B%20ZENAIR%20CH601-XL.pdf where theCoG range is given as 300 to 520 mm aft of datum (datum is leading edge). I hope that this is useful info. Andrew. -------- A good way through building a 601UL with 912UL. Still flying Rans S6 with 503. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=222809#222809


    Message 2


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 11:09:41 AM PST US
    Subject: Elevator bias spring
    From: jaybannist@cs.com
    Any suggestions on finding the details about the elevator bias spring -? CZAW drawing 6-BO-4CZ ? Jay in Dallas ________________________________________________________________________ Email message sent from CompuServe - visit us today at http://www.cs.com


    Message 3


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 12:36:05 PM PST US
    From: "David Johnson" <david_a_g_johnson@btinternet.com>
    Subject: Re: Elevator bias spring
    Jay, I (after much e-mailing) got the attached drawing from CZAW and I hope you find it more use than I did! In the end I found out, from the UK agents, that all you need is a spring that will apply about 6 - 10 lbs of back pressure on the stick when the flap is lowered. Dave Johnson 601XL Jab3300, almost ready for test flying AND GROUNDED!!!!!! do not archive ----- Original Message ----- From: jaybannist@cs.com To: zenith601-list@matronics.com ; zenith-list@matronics.com Sent: Sunday, January 04, 2009 7:08 PM Subject: Zenith601-List: Elevator bias spring Any suggestions on finding the details about the elevator bias spring - CZAW drawing 6-BO-4CZ ? Jay in Dallas ------------------------------------------------------------------------- ----- Email message sent from CompuServe - visit us today at http://www.cs.com


    Message 4


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 01:39:44 PM PST US
    Subject: Re: Elevator bias spring
    From: jaybannist@cs.com
    Thanks for sending it, but, you are right.? It is pretty much useless. I was curious, because I had never heard of an "elevator bias spring".? Now that I know what it is, I know I don't need one. Jay in Dallas Do not archive -----Original Message----- From: David Johnson <david_a_g_johnson@btinternet.com> Sent: Sun, 4 Jan 2009 2:35 pm Subject: Re: Zenith601-List: Elevator bias spring Jay, ? I (after much e-mailing) got the attached drawing from CZAW and I hope you find it more use than I did! ? In the end I found out, from the UK agents, that all you need is a spring that will apply about 6 - 10 lbs of back pressure on the stick when the flap is lowered. ? Dave Johnson ? 601XL Jab3300, almost ready for test flying AND GROUNDED!!!!!! ? do not archive ----- Original Message ----- From: jaybannist@cs.com zenith-list@matronics.com Sent: Sunday, January 04, 2009 7:08 PM Subject: Zenith601-List: Elevator bias spring Any suggestions on finding the details about the elevator bias spring -? CZAW drawing 6-BO-4CZ ? Jay in Dallas Email message sent from CompuServe - visit us today at http://www.cs.com href="http://www.matronics.com/Navigator?Zenith601-List">http://www.matronics.com/Navigator?Zenith601-List href="http://forums.matronics.com">http://forums.matronics.com href="http://www.matronics.com/contribution">http://www.matronics.com/c ________________________________________________________________________ Email message sent from CompuServe - visit us today at http://www.cs.com




    Other Matronics Email List Services

  • Post A New Message
  •   zenith601-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/Zenith601-List.htm
  • Web Forum Interface To Lists
  •   http://forums.matronics.com
  • Matronics List Wiki
  •   http://wiki.matronics.com
  • 7-Day List Browse
  •   http://www.matronics.com/browse/zenith601-list
  • Browse Zenith601-List Digests
  •   http://www.matronics.com/digest/zenith601-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contribution

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --