Zenith601-List Digest Archive

Thu 05/14/09


Total Messages Posted: 6



Today's Message Index:
----------------------
 
     1. 08:03 AM - Aileron cable length (Bob McArdle)
     2. 09:11 AM - Re: Aileron cable length (Jim Belcher)
     3. 10:08 AM - Re: Aileron cable length (T. Graziano)
     4. 04:17 PM - Re: Aileron cable length (Ron Lendon)
     5. 04:42 PM - 601 Rotax Engine Mount (Tommy Walker)
     6. 10:28 PM - Re: 601 Rotax Engine Mount (K Dilks)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 08:03:38 AM PST US
    From: "Bob McArdle" <rmacpunk@netzero.net>
    Subject: Aileron cable length
    Does anyone have the total length of each aileron cable before turnbuckles,thimbles,clevis and nicopress. Thanks


    Message 2


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 09:11:56 AM PST US
    From: Jim Belcher <z601@anemicaardvark.com>
    Subject: Re: Aileron cable length
    On Thursday 14 May 2009 09:58, Bob McArdle wrote: > Does anyone have the total length of each aileron cable before > turnbuckles,thimbles,clevis and nicopress. Thanks I'm no doubt a devout coward, but I always initially cut cables longer thanthey could possibly need to be. Without a cable jig, it's almost impossible to get them the right length. That way, I don't wind up finddling around trying to s-t-r-e-t-c-h that extra inch that isn't there. Mine are cut to reach the far side of the cockpit. I don't doubt that I may wind up buying more cable, but that's cheap compared to trying to the frustration of having the cable too short, or having to be too ultra precise in my measurements. -- ============================================ Do not archive. ============================================ Jim B Belcher BS, MS Physics, Math, Computer Science A&P/IA Retired aerospace technical manager ============================================


    Message 3


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 10:08:17 AM PST US
    From: "T. Graziano" <tonyplane@bellsouth.net>
    Subject: Re: Aileron cable length
    F W I W: In my kit, ser 6-5342, there was more than enough cable to permit the "rough cuts" to be long. I had quite a bit of cable left. I also had plenty of spare rivets left over. Zenith did provide enough material in the kit. Tony Graziano XL/Jab3300; N493TG; 490 hrs ----- Original Message ----- From: "Jim Belcher" <z601@anemicaardvark.com> Sent: Thursday, May 14, 2009 10:44 AM Subject: Re: Zenith601-List: Aileron cable length > <z601@anemicaardvark.com> > > On Thursday 14 May 2009 09:58, Bob McArdle wrote: >> Does anyone have the total length of each aileron cable before >> turnbuckles,thimbles,clevis and nicopress. Thanks > > I'm no doubt a devout coward, but I always initially cut cables longer > thanthey could possibly need to be. Without a cable jig, it's almost > impossible to get them the right length. That way, I don't wind up > finddling > around trying to s-t-r-e-t-c-h that extra inch that isn't there. Mine are > cut > to reach the far side of the cockpit. > > I don't doubt that I may wind up buying more cable, but that's cheap > compared > to trying to the frustration of having the cable too short, or having to > be > too ultra precise in my measurements. > -- > ============================================ > Do not archive. > ============================================ > Jim B Belcher > BS, MS Physics, Math, Computer Science > A&P/IA > Retired aerospace technical manager > ============================================ > > >


    Message 4


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 04:17:55 PM PST US
    Subject: Re: Aileron cable length
    From: "Ron Lendon" <rlendon@comcast.net>
    [quote="rmacpunk(at)netzero.net"]Does anyone have the total length of each aileron cable before turnbuckles,thimbles,clevis and nicopress. Thanks [quote] Maybe ya could use a string first? A strong string should be able to get you pretty close. -------- Ron Lendon, Clinton Township, MI WW Corvair with Roy's Garage 5th bearing Zodiac XL, ScrapBuilder ;-) http://www.mykitlog.com/rlendon Corvair Engine Prints: http://home.comcast.net/~rlendon/site/ Read this topic online here: http://forums.matronics.com/viewtopic.php?p=244058#244058


    Message 5


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 04:42:14 PM PST US
    Subject: 601 Rotax Engine Mount
    From: "Tommy Walker" <twalker@cableone.net>
    601 builders. I have a CZEC built 601XL Rotax 921ULS motor mount that is for sale. It includes everything except a couple of the bolts used for mounting. If you are interested, I will sell it for $100.00 US, plus shipping. The mount was removed from a 2003 XL. I also have a couple of other parts that would fit a Rotax 601XL. Contact me at twalker(at) cableone.net Tommy Walker in Alabama -------- Tommy Walker N8701 - Anniston, AL Read this topic online here: http://forums.matronics.com/viewtopic.php?p=244060#244060


    Message 6


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 10:28:12 PM PST US
    Subject: Re: 601 Rotax Engine Mount
    From: "K Dilks" <kevin.dilks@liwest.at>
    PM sent thanks Kev -------- Austria ............. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=244094#244094




    Other Matronics Email List Services

  • Post A New Message
  •   zenith601-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/Zenith601-List.htm
  • Web Forum Interface To Lists
  •   http://forums.matronics.com
  • Matronics List Wiki
  •   http://wiki.matronics.com
  • 7-Day List Browse
  •   http://www.matronics.com/browse/zenith601-list
  • Browse Zenith601-List Digests
  •   http://www.matronics.com/digest/zenith601-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contribution

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --