Today's Message Index:
----------------------
1. 03:00 PM - Flap Stop Importance ??? (Thruster87)
2. 03:49 PM - Wing tip height xl (Bob McArdle)
3. 04:13 PM - Re: Wing tip height xl (Paul Mulwitz)
4. 04:24 PM - Re: Wing tip height xl (jaybannist@cs.com)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Flap Stop Importance ??? |
In order to ensure accurate results, all tests were carried out on two different
Zodiac aircraft. The significance of the flap stops called-for as part of the
regular design was confirmed. The aircraft which did not at first have these
installed showed less satisfactory results than Zenair's own standard demo plane
(with stops) which was one of the tested planes. Zenair will be issuing a
Service Letter very shortly calling for owners/pilots to check their flap stops
(and to install them prior to further flight operations if these have not been
previously fitted). I wonder what they mean by LESS SATISFACTORY RESULTS WITHOUT
THE STOPS??????? Cheers
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=246206#246206
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Wing tip height xl |
Can someone give me the approx wing tip height from the ground. I am in
the process of fitting the wings and do'nt wish to cut off too much
metal on the inboard side. Thanks
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Wing tip height xl |
Hi Bob,
If you do cut off to much metal on the inboard end of a wing, it is
easy to add a strip from the last rib to the final position you
want. Actually, this is a lot easier than cutting the existing skin
since you can fit a template to the fuselage (I like styrene plastic
sheet for this) and later position it to drill for the rivet line on
the inboard rib.
If you make a nice edge to the "Fairing" it looks like you planned it
all along.
Paul
XL grounded
At 03:46 PM 5/31/2009, you wrote:
>Can someone give me the approx wing tip height from the ground. I
>am in the process of fitting the wings and do'nt wish to cut off too
>much metal on the inboard side. Thanks
>
>
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: Wing tip height xl |
Bob,
>From the fattest part of the bottom of the wing at the bottom of the tip plate
is approximately 4' - 5".? Geive me a couple of hours and I'll send you a narrative
of how I did it along with a drawing and photo.
Jay Bannister
Do not archive.?
-----Original Message-----
From: Bob McArdle <rmacpunk@netzero.net>
Sent: Sun, 31 May 2009 5:46 pm
Subject: Zenith601-List: Wing tip height xl
Can? someone give me the approx wing tip
height from the ground. I am in the process of fitting the wings and do'nt wish
to cut off too much metal on the inboard side. Thanks
________________________________________________________________________
Email message sent from CompuServe - visit us today at http://www.cs.com
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|