Zenith601-List Digest Archive

Sat 07/11/09


Total Messages Posted: 4



Today's Message Index:
----------------------
 
     1. 04:26 AM - canopy cable support 6C4-1 (chris Sinfield)
     2. 06:32 AM - Re: canopy cable support 6C4-1 (skyriderekm)
     3. 08:48 AM - Re: canopy cable support 6C4-1 (Bill Naumuk)
     4. 08:35 PM - Re: canopy cable support 6C4-1 (chris Sinfield)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 04:26:14 AM PST US
    Subject: canopy cable support 6C4-1
    From: "chris Sinfield" <chris_sinfield@yahoo.com.au>
    Ok Can I get some clarification and the search function did not come up with any responses worries me I may be in the wrong.. On the plans page 6-C-4 03/06 Part No 6C4-1 located on the fwd side of the canopy handle assembly shows it facing aft towards the handle. When I measured the location this part inter-fears with the FWD hoop bracket 6-C3-9 . also the photo guide shows it reversed from the plans. Which is correct? It works reversed to the plan. Was there a correction I missed? Also the plans do not say what type of rivets to use. Steel part to steal Support bracket.. AL rivets or SS rivets? Chris.. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=252538#252538


    Message 2


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 06:32:43 AM PST US
    Subject: Re: canopy cable support 6C4-1
    From: "skyriderekm" <skyriderekm@yahoo.com>
    Chris, I suggest you write (or better call) Zenith for clarification on this. I have the new style CH650 fuselage but my photo/instructional guide is of the CH601 so I can't help you in that respect. My point is that Zenith is putting out kits without updating the information on their website. That is just wrong. I would hate to "assume" anything and install something wrong myself. I hope Zenith responds to you in a timely manner and updates their website soon. Tailwinds, Larry Hursh Read this topic online here: http://forums.matronics.com/viewtopic.php?p=252548#252548


    Message 3


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 08:48:56 AM PST US
    From: "Bill Naumuk" <naumuk@windstream.net>
    Subject: Re: canopy cable support 6C4-1
    Chris- You really had me worried for a moment. The only thing I can think of is you're measuring from the end of the "Foot" of 6C4-1 rather than at the intersection of the bend. That's the only way you could be off more than 2mm whether the fitting was faced forward or aft. I just measured my side rail and there's tons of room between where the fitting is and where the front hoop is supposed to go. I used the print dimensions and welded 6C4-1 to the square tubing. Picture attached, hope this helps. Bill ----- Original Message ----- From: "chris Sinfield" <chris_sinfield@yahoo.com.au> Sent: Saturday, July 11, 2009 7:25 AM Subject: Zenith601-List: canopy cable support 6C4-1 > <chris_sinfield@yahoo.com.au> > > Ok Can I get some clarification and the search function did not come up > with any responses worries me I may be in the wrong.. > > On the plans page 6-C-4 03/06 Part No 6C4-1 located on the fwd side of > the canopy handle assembly shows it facing aft towards the handle. > > When I measured the location this part inter-fears with the FWD hoop > bracket 6-C3-9 . also the photo guide shows it reversed from the plans. > > Which is correct? It works reversed to the plan. Was there a correction I > missed? Also the plans do not say what type of rivets to use. Steel part > to steal Support bracket.. AL rivets or SS rivets? > > Chris.. > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=252538#252538 > > >


    Message 4


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 08:35:03 PM PST US
    Subject: Re: canopy cable support 6C4-1
    From: "chris Sinfield" <chris_sinfield@yahoo.com.au>
    Bill Can you measure from the bolt hole at the FWD end of the Side frame to the front hoop bracket 6C3-9 and also to the center of the vertical part of the 6C4-1 that you welded.. so 2 measurements. Fwd hoop bracket is 510mm next is the cable support at 6C4-1 at ???mm Chris.. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=252624#252624




    Other Matronics Email List Services

  • Post A New Message
  •   zenith601-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/Zenith601-List.htm
  • Web Forum Interface To Lists
  •   http://forums.matronics.com
  • Matronics List Wiki
  •   http://wiki.matronics.com
  • 7-Day List Browse
  •   http://www.matronics.com/browse/zenith601-list
  • Browse Zenith601-List Digests
  •   http://www.matronics.com/digest/zenith601-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contribution

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --