Zenith601-List Digest Archive

Fri 09/25/09


Total Messages Posted: 5



Today's Message Index:
----------------------
 
     1. 01:39 AM - Flap position Indicator (Thruster87)
     2. 04:42 AM - Re: Wanted Zenith 601xl Decal (Afterfxllc@aol.com)
     3. 06:45 AM - Re: Wanted Zenith 601xl Decal (Gig Giacona)
     4. 01:37 PM - Instrument panel files for CH601XL (mhubel)
     5. 01:40 PM - Re: Wanted Zenith 601xl Decal (Thruster87)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 01:39:14 AM PST US
    Subject: Flap position Indicator
    From: "Thruster87" <alania@optusnet.com.au>
    Anyone used a ELECTRONIC FLAP CONTROLLER The Flap Controller is a combination drive unit for the flap actuator, and an indicator of flap position. It features momentary push button switches with built in green LED lights, providing settings for 4 flap positions. Each switch can be user pro- grammed to a specific flap position. Once calibrated, momentarily pushing any switch, will then automatically drive the flaps to the pre selected position and stop.The flap controller can work with any actuator that draws less than 7 amps current at 12 volts when operating. It requires that the system have a 5K or 10K resistive position sensor that provides feedback of flap position. Many actuators incorporate this type of sensor in the unit, or separate linear resistive sensors are available from equipment suppliers. Cheers Read this topic online here: http://forums.matronics.com/viewtopic.php?p=264890#264890


    Message 2


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 04:42:46 AM PST US
    From: Afterfxllc@aol.com
    Subject: Re: Wanted Zenith 601xl Decal
    I can cut them for you... I did the vinyl for my plane. I am changing where the ZODIAC 601XL is on the wing tip I don't like how it looks. Jeff


    Message 3


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 06:45:42 AM PST US
    Subject: Re: Wanted Zenith 601xl Decal
    From: "Gig Giacona" <wrgiacona@gmail.com>
    ACS has a couple -------- W.R. &quot;Gig&quot; Giacona 601XL Under Construction See my progress at www.peoamerica.net/N601WR Read this topic online here: http://forums.matronics.com/viewtopic.php?p=264910#264910


    Message 4


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 01:37:27 PM PST US
    Subject: Instrument panel files for CH601XL
    From: "mhubel" <mhubel@nemon.com>
    I have posted a set of turbocad files that were used for the CH601XL. These are on http://groups.yahoo.com/group/jabiruengines/files/ you may need to register to access them. The files are under the file name turbocad_CH601_instrument_panel_N708HU.zip Included in the files are three layers (options->layers) that are the actual holes, the part outlines and the space guidelines. Only the first (black) layer is to be used for fabrication. The instrument panel was actually made by Rapid Sheet Metal Inc Kristen Spratt 603-821-5300 603-889-4266 fax customerservice@rapidsheetmetal.com This design was $390 (quantity 1) including painting. The cost won't vary much with the layout. It was 0.090 thick and was painted by Rapid Sheet Metal. It was put on top of the sheet metal already there. All openings in he existing panel were made slightly oversize for ease of alignment. If you use these drawings and this vendor, I suggest not using any countersunk screw holes as these are 2D drawings and the countersunk holes really don't make it look any better. -------- Mark Hubelbank Read this topic online here: http://forums.matronics.com/viewtopic.php?p=265005#265005


    Message 5


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 01:40:47 PM PST US
    Subject: Re: Wanted Zenith 601xl Decal
    From: "Thruster87" <alania@optusnet.com.au>
    Afterfxllc(at)aol.com wrote: > I can cut them for you... I did the vinyl for my plane. > > I am changing where the ZODIAC 601XL is on the wing tip I don't like how it looks. > > Jeff Thank you for the offer but I'm after the Zenith Logo Cheers Alan Read this topic online here: http://forums.matronics.com/viewtopic.php?p=265007#265007 Attachments: http://forums.matronics.com//files/zac_logo_117.gif




    Other Matronics Email List Services

  • Post A New Message
  •   zenith601-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/Zenith601-List.htm
  • Web Forum Interface To Lists
  •   http://forums.matronics.com
  • Matronics List Wiki
  •   http://wiki.matronics.com
  • 7-Day List Browse
  •   http://www.matronics.com/browse/zenith601-list
  • Browse Zenith601-List Digests
  •   http://www.matronics.com/digest/zenith601-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contribution

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --