Zenith601-List Digest Archive

Wed 10/07/09


Total Messages Posted: 4



Today's Message Index:
----------------------
 
     1. 12:49 PM - Firewall Forward Kit from Jab USA/Camloc Fasteners (AZFlyer)
     2. 01:24 PM - Re: Firewall Forward Kit from Jab USA/Camloc Fasteners (KARL POLIFKA)
     3. 01:33 PM - Re: Firewall Forward Kit from Jab USA/Camloc Fasteners (mhubel)
     4. 03:15 PM - Re: Firewall Forward Kit from Jab USA/Camloc Fasteners (Paul Mulwitz)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 12:49:06 PM PST US
    Subject: Firewall Forward Kit from Jab USA/Camloc Fasteners
    From: "AZFlyer" <millrML@aol.com>
    List, For those using the Jab USA supplied FWF kit: Has anybody found the "Camloc Fasteners" (10 - Camloc #26S8-6) to be too long for the cowl? Just right? or ? My cowl thickness seems to be around .150" which would indicate a 26S8-4 or -5. I may be measuring incorrectly.....? Thanks for feedback. Mike -------- Mike Miller @ millrml@aol.com 601 XL, 3300, Dynon Remember, &quot;the second mouse gets the cheese&quot;! Read this topic online here: http://forums.matronics.com/viewtopic.php?p=266981#266981


    Message 2


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 01:24:04 PM PST US
    From: "KARL POLIFKA" <jfowler120@verizon.net>
    Subject: Re: Firewall Forward Kit from Jab USA/Camloc Fasteners
    We have a Jabiru FWF kit of a few years ago. The camlocs vary from # 5 to #6 for reasons I can't explain -- just reality. Karl Polifka ----- Original Message ----- From: AZFlyer To: zenith601-list@matronics.com Sent: Wednesday, October 07, 2009 3:48 PM Subject: Zenith601-List: Firewall Forward Kit from Jab USA/Camloc Fasteners List, For those using the Jab USA supplied FWF kit: Has anybody found the "Camloc Fasteners" (10 - Camloc #26S8-6) to be too long for the cowl? Just right? or ? My cowl thickness seems to be around .150" which would indicate a 26S8-4 or -5. I may be measuring incorrectly.....? Thanks for feedback. Mike -------- Mike Miller @ millrml@aol.com 601 XL, 3300, Dynon Remember, &quot;the second mouse gets the cheese&quot;! Read this topic online here: http://forums.matronics.com/viewtopic.php?p=266981#266981


    Message 3


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 01:33:42 PM PST US
    Subject: Re: Firewall Forward Kit from Jab USA/Camloc Fasteners
    From: "mhubel" <mhubel@nemon.com>
    I found that the fiberglass thickness was highly variable and there was no one size camloc that would work everywhere. Going just by the measurement may also lead to cams that are somewhat hard to open or almost fall out. I bought a few on each side of ideal and did a best fit to each hole. I used a range of #4 to #6. -------- Mark Hubelbank Read this topic online here: http://forums.matronics.com/viewtopic.php?p=266996#266996


    Message 4


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 03:15:04 PM PST US
    From: Paul Mulwitz <psm@att.net>
    Subject: Re: Firewall Forward Kit from Jab USA/Camloc Fasteners
    I glued in a little extra fiberglass where it was needed to make the cowl the right thickness for the camlocs. This was needed in some places and not in other places. Paul XL awaiting engineering changes At 12:48 PM 10/7/2009, you wrote: >Has anybody found the "Camloc Fasteners" (10 - Camloc #26S8-6) to be >too long for the cowl? Just right? or ?




    Other Matronics Email List Services

  • Post A New Message
  •   zenith601-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/Zenith601-List.htm
  • Web Forum Interface To Lists
  •   http://forums.matronics.com
  • Matronics List Wiki
  •   http://wiki.matronics.com
  • 7-Day List Browse
  •   http://www.matronics.com/browse/zenith601-list
  • Browse Zenith601-List Digests
  •   http://www.matronics.com/digest/zenith601-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contribution

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --