Today's Message Index:
----------------------
 
     1. 12:46 PM - Drilling 1/8" hole on the fuel vent tube (Thruster87)
     2. 06:17 PM - Re: Drilling 1/8" hole on the fuel vent tube (Ron Lendon)
     3. 06:35 PM - Re: Drilling 1/8" hole on the fuel vent tube (Thruster87)
     4. 10:31 PM - Re: Drilling 1/8" hole on the fuel vent tube (Thruster87)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
12:46:50 PM PST US
Subject: 
Drilling 1/8" hole on the fuel vent tube
From: 
"Thruster87" <alania@optusnet.com.au>
      
      
      How many of you have drilled a 1/8' hole at the back of the fuel vent tubes [just
      above the angle cutout] to stop siphoning ????? Is it really needed ???  Cheers
      T87
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=268835#268835
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
06:17:46 PM PST US
Subject: 
Re: Drilling 1/8" hole on the fuel vent tube
From: 
"Ron Lendon" <rlendon@comcast.net>
      
      
      Is that hole called out in the prints?  I must have missed that.
      
      --------
      Ron Lendon, Clinton Township, MI
      WW Corvair with Roy's Garage 5th bearing
      Zodiac XL, ScrapBuilder ;-)
      http://www.mykitlog.com/rlendon
      Corvair Engine Prints:
      http://home.comcast.net/~rlendon/site/
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=268870#268870
      
      

Message 3


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
06:35:17 PM PST US
Subject: 
Re: Drilling 1/8" hole on the fuel vent tube
From: 
"Thruster87" <alania@optusnet.com.au>
      
      
      
      Ron Lendon wrote:
      > Is that hole called out in the prints?  I must have missed that.
       It was in the final check list [about 20 odd pages] for a new 601xl. Can't remember
      where I down loaded it.Cheers Alan
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=268873#268873
      
      

Message 4


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
10:31:10 PM PST US
Subject: 
Re: Drilling 1/8" hole on the fuel vent tube
From: 
"Thruster87" <alania@optusnet.com.au>
      
      
      It was in this document
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=268887#268887
      
      
      Attachments: 
      
      http://forums.matronics.com//files/ch_601_xl_slsa_pre_flight_inspection_2008_270.pdf
      
      








Other Matronics Email List Services




Post A New Message
  
zenith601-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/Zenith601-List.htm
Web Forum Interface To Lists
  
http://forums.matronics.com
Matronics List Wiki
  
http://wiki.matronics.com
7-Day List Browse
  
http://www.matronics.com/browse/zenith601-list
Browse Zenith601-List Digests
  
http://www.matronics.com/digest/zenith601-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --