---------------------------------------------------------- Zenith601-List Digest Archive --- Total Messages Posted Wed 10/21/09: 4 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 12:46 PM - Drilling 1/8" hole on the fuel vent tube (Thruster87) 2. 06:17 PM - Re: Drilling 1/8" hole on the fuel vent tube (Ron Lendon) 3. 06:35 PM - Re: Drilling 1/8" hole on the fuel vent tube (Thruster87) 4. 10:31 PM - Re: Drilling 1/8" hole on the fuel vent tube (Thruster87) ________________________________ Message 1 _____________________________________ Time: 12:46:50 PM PST US Subject: Zenith601-List: Drilling 1/8" hole on the fuel vent tube From: "Thruster87" How many of you have drilled a 1/8' hole at the back of the fuel vent tubes [just above the angle cutout] to stop siphoning ????? Is it really needed ??? Cheers T87 Read this topic online here: http://forums.matronics.com/viewtopic.php?p=268835#268835 ________________________________ Message 2 _____________________________________ Time: 06:17:46 PM PST US Subject: Zenith601-List: Re: Drilling 1/8" hole on the fuel vent tube From: "Ron Lendon" Is that hole called out in the prints? I must have missed that. -------- Ron Lendon, Clinton Township, MI WW Corvair with Roy's Garage 5th bearing Zodiac XL, ScrapBuilder ;-) http://www.mykitlog.com/rlendon Corvair Engine Prints: http://home.comcast.net/~rlendon/site/ Read this topic online here: http://forums.matronics.com/viewtopic.php?p=268870#268870 ________________________________ Message 3 _____________________________________ Time: 06:35:17 PM PST US Subject: Zenith601-List: Re: Drilling 1/8" hole on the fuel vent tube From: "Thruster87" Ron Lendon wrote: > Is that hole called out in the prints? I must have missed that. It was in the final check list [about 20 odd pages] for a new 601xl. Can't remember where I down loaded it.Cheers Alan Read this topic online here: http://forums.matronics.com/viewtopic.php?p=268873#268873 ________________________________ Message 4 _____________________________________ Time: 10:31:10 PM PST US Subject: Zenith601-List: Re: Drilling 1/8" hole on the fuel vent tube From: "Thruster87" It was in this document Read this topic online here: http://forums.matronics.com/viewtopic.php?p=268887#268887 Attachments: http://forums.matronics.com//files/ch_601_xl_slsa_pre_flight_inspection_2008_270.pdf ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message zenith601-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Zenith601-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/zenith601-list Browse Digests http://www.matronics.com/digest/zenith601-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.