Today's Message Index:
----------------------
1. 04:33 AM - XL nose wheel fairing fitment (chris Sinfield)
2. 05:43 AM - Re: XL nose wheel fairing fitment (jaybannist@cs.com)
3. 09:12 AM - Re: 601 XL manual online? (Pete54)
4. 02:07 PM - Re: XL nose wheel fairing fitment (chris Sinfield)
5. 02:43 PM - Re: Re: XL nose wheel fairing fitment (Peter W Johnson)
6. 07:43 PM - axle spacers (chris Sinfield)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | XL nose wheel fairing fitment |
hey I have the 2006 fiberglass nose wheel fairings
I have the photo guides but the WFO-1 plans do not show the size of the sloping
Aluminum strip that is riveted to the front portions of the wheel fairing.
Everything else was in the kit but the 2 brackets.. (and they are not on the plans)..
So what size and thickness are they please? and I will make them..
Chris..
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=288273#288273
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: XL nose wheel fairing fitment |
Chris,
Is this what you are looking for?
Jay Bannister
-----Original Message-----
From: chris Sinfield <chris_sinfield@yahoo.com.au>
Sent: Fri, Feb 26, 2010 6:32 am
Subject: Zenith601-List: XL nose wheel fairing fitment
oo.com.au>
hey I have the 2006 fiberglass nose wheel fairings
I have the photo guides but the WFO-1 plans do not show the size of the sl
oping
Aluminum strip that is riveted to the front portions of the wheel fairing.
Everything else was in the kit but the 2 brackets.. (and they are not on
the
plans)..
So what size and thickness are they please? and I will make them..
Chris..
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=288273#288273
========================
===========
========================
===========
========================
===========
========================
===========
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: 601 XL manual online? |
The LAA modifications for the UK fleet set a compulsory maximum fuselage weight
of 494kg, 1087lbs following their re-analysis of the airframe.
It still leaves a reasonably payload but does indicate the apparent short comings
their saw in the design do exist.
--------
Pete Morris
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=288318#288318
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: XL nose wheel fairing fitment |
thanks Jay
I have the plans page . The Plate I am talking about is where the rear part of
the fiberglass fairing, is attached to the fwd part of the nose wheel fairing.
It has rivets and anchor nuts on it.
what size and thickness and spacing of the anchor nuts..
I cant find it on the plans I do see it on the photo guide but not its dimensions
or thickness or where the holes are located..
Thanks. anyone with it measure it please
Chris
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=288384#288384
Message 5
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: XL nose wheel fairing fitment |
Chris,
I made mine out of some scrap .025 I had lying around. It fits the whole
length of the cut (minus a few mm each end) and is about 50mm wide in total.
I riveted the plate to the front and has nut plates for the rear half.
Next time out at the hangar (tomorrow) I'll take a picture or two.
Cheers
Peter
Wonthaggi Australia
-----Original Message-----
From: owner-zenith601-list-server@matronics.com
[mailto:owner-zenith601-list-server@matronics.com] On Behalf Of chris
Sinfield
Sent: Saturday, 27 February 2010 9:05 AM
Subject: Zenith601-List: Re: XL nose wheel fairing fitment
<chris_sinfield@yahoo.com.au>
thanks Jay
I have the plans page . The Plate I am talking about is where the rear part
of the fiberglass fairing, is attached to the fwd part of the nose wheel
fairing. It has rivets and anchor nuts on it.
what size and thickness and spacing of the anchor nuts..
I cant find it on the plans I do see it on the photo guide but not its
dimensions or thickness or where the holes are located..
Thanks. anyone with it measure it please
Chris
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=288384#288384
Message 6
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Gang
on 6-G-1 the Nose wheel axle spacers are 31 mm on my plans 03/06
now on the update the spacers are 33.4 mm ( about the thickness of another washer?)
anyone know the reason behind the change to the longer spacer?
were they not doing up tight enough before bottoming out?
anyone know
chris
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=288446#288446
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|