Today's Message Index:
----------------------
1. 03:33 PM - Re: Zenith601-List Digest: 2 Msgs - 03/29/10 (gpjann1@netzero.com)
2. 04:44 PM - Wing Support points (Damien)
3. 05:34 PM - Re: Wing Support points (Larry McFarland)
4. 06:48 PM - Re: Wing Support points (Michel Therrien)
5. 07:25 PM - Re: Wing Support points (Damien)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Zenith601-List Digest: 2 Msgs - 03/29/10 |
Does anyone have Zodiac 601 HDS LE fuel tanks for sale?
Also looking for 8 gal. header tank.
Thanks,
Greg
770-277-1637
gpjann1@netzero.com
____________________________________________________________
Staples® - Weekly Ad
Incredible deals at Staples! Buy 1 get 1 case paper and much more!!
http://thirdpartyoffers.netzero.net/TGL3241/4bb27bcc6a4c1e4d0st01vuc
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Wing Support points |
Hello. Where are the sections on a 601 HDS wing that will support the
plane underneath? I plan on replacing the nose bungee and in addition to
tying
down the tail and lifting up on the engine, I would like to place a
support under each wing in case of failure. My guess is that the support
point would be under the
area where we walk on the wing.
Regards,
Damien
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Wing Support points |
Hi Damien,
I made a set of wing stands to do the job. The wings were off when I did
these, but you could make a set that supports the spar area
as shown here. You may have to adjust the angle a bit, but I replaced
bungees one at a time while on this rig. Lift the airplane, set in the pin.
or just place the support under the spar.
See attached image.
Larry McFarland
Damien wrote:
> Hello. Where are the sections on a 601 HDS wing that will support the
> plane underneath? I plan on replacing the nose bungee and in addition
> to tying
> down the tail and lifting up on the engine, I would like to place a
> support under each wing in case of failure. My guess is that the
> support point would be under the
> area where we walk on the wing.
> Regards,
> Damien
> *
> *
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Wing Support points |
Not sure what you mean, but if it is to put the plane on saw horses or some
thing like that, I'd say that anywhere under the main spar should be good (
main rivet line underneath)... at least, this is the case for the 601 HD.
-
-
Here is a not so fun example...:
----------------------------
Michel Therrien CH601-HD, C-GZGQ
http://mthobby.pcperfect.com/ch601
http://pages.infinit.net/mthobby
--- On Tue, 3/30/10, Damien <dgraham7@TWCNY.RR.COM> wrote:
From: Damien <dgraham7@TWCNY.RR.COM>
Subject: Zenith601-List: Wing Support points
Received: Tuesday, March 30, 2010, 7:43 PM
Hello. Where are the sections on a 601 HDS wing that will support the plane
underneath? ....=0A=0A=0A ___________________________________________
_______________________=0AYahoo! Canada Toolbar: Search from anywhere on th
e web, and bookmark your favourite sites. Download it now=0Ahttp://ca.toolb
ar.yahoo.com.
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Wing Support points |
Thanks Michel and Larry. That is just what I needed. And thanks
for the photos too.
Regards,
Damien
DO NOT ARCHIVE
----- Original Message -----
From: Michel Therrien
To: zenith601-list@matronics.com
Sent: Tuesday, March 30, 2010 9:46 PM
Subject: Re: Zenith601-List: Wing Support points
Not sure what you mean, but if it is to put the plane on saw
horses or something like that, I'd say that anywhere under the main spar
should be good (main rivet line underneath)... at least, this is the
case for the 601 HD.
Here is a not so fun example...:
----------------------------
Michel Therrien CH601-HD, C-GZGQ
http://mthobby.pcperfect.com/ch601
http://pages.infinit.net/mthobby
--- On Tue, 3/30/10, Damien <dgraham7@TWCNY.RR.COM> wrote:
From: Damien <dgraham7@TWCNY.RR.COM>
Subject: Zenith601-List: Wing Support points
To: zenith601-list@matronics.com
Received: Tuesday, March 30, 2010, 7:43 PM
Hello. Where are the sections on a 601 HDS wing that will
support the plane underneath? ....
-------------------------------------------------------------------------
-----
The new Internet Explorer=AE 8 - Faster, safer, easier. Optimized for
Yahoo! Get it Now for Free!
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|