Today's Message Index:
----------------------
1. 02:33 AM - Re: different upgrade Q (Ianrat)
2. 11:38 AM - Re: Re: Aileron Stop after Mod (Alan & Brenda)
3. 02:21 PM - Re: Re: Bad takeoff, but still good landing (Michel Therrien)
4. 02:54 PM - Re: Aileron Stop after Mod (chris Sinfield)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: different upgrade Q |
Chris i have use a small rivet from the back side of the wind just to close the
hole and make it look better.
Ianrat
CH601XL
Brisbane :D
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=299244#299244
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Aileron Stop after Mod |
T=.040 6061-T6
Bottom 108 deg bend 20 mm long,
Vertical 15 mm long,
56 deg bend 29 mm long,
56 deg bend Vertical 15 mm
Sorry I can not scan
Brenda Smith CH650
--------------------------------------------------
From: "chris Sinfield" <chris_sinfield@yahoo.com.au>
Sent: Friday, May 28, 2010 3:19 PM
Subject: Zenith601-List: Re: Aileron Stop after Mod
> <chris_sinfield@yahoo.com.au>
>
> well if there is a new stop designed,
>
> can someone with the latest version of the plans ( 650 I guess) scan in
> the aileron stop so we all can see how it is done? size wise / thickness?
>
> Chris.
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=299195#299195
>
>
>
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Bad takeoff, but still good landing |
Hello all,
I found the problem today. I had another Holley 5200 carb at home that I studied.
I examined the fload mechanism. Then, I went back to the airport and opened
the carb and this time, noticed that the movement of the float was very restrained.
I then saw the issue. The floats activates a needle that seats in
the bottom of a female piece. That piece was unscrewed! (see picture attached)
So, the needle would seat and restrict the flow at low bowl fuel level.
That was easilly repared.
I tested my engine on the ground, holding it between 4600 and 4900 rpm with no
mis or anything like that.... so, I'll fly it may be tomorrow.
It is a bit frightening to see how we depend on so small things when we fly. An
annual inspection would not reveal this type of problem.
Thanks all who provided ideas of what to look for.
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Aileron Stop after Mod |
thanks
I / we should be able to work with that.
Chris
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=299299#299299
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|