Zenith601-List Digest Archive

Tue 08/31/10


Total Messages Posted: 5



Today's Message Index:
----------------------
 
     1. 04:55 AM - center spar upgrade 6ZU 3-2 (chris Sinfield)
     2. 07:34 AM - Re: center spar upgrade 6ZU 3-2 (DaveG601XL)
     3. 08:00 AM - Re: Re: center spar upgrade 6ZU 3-2 (Afterfxllc@aol.com)
     4. 08:54 AM - Re: center spar upgrade 6ZU 3-2 (DaveG601XL)
     5. 07:17 PM - Re: center spar upgrade 6ZU 3-2 (Ron Lendon)
 
 
 


Message 1


  • INDEX
  • Back to Main INDEX
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 04:55:59 AM PST US
    Subject: center spar upgrade 6ZU 3-2
    From: "chris Sinfield" <chris_sinfield@yahoo.com.au>
    Hi gang can someone please shoot me a picture of how this piece sits against the side of the fuselage skin and around the rear spar upright. I am a bit confused . Does it sit fully next to the skin between the upright at the undercarriage and the rear spar upright or Does it go between the skin and upright at the back but at the front section you have side skin/spar upright/ 6zu3-2 and then the bracket 6B10-4 over the lot. Chris.. the Zenith Aero video was not clear on this and the photo guide shows it going behind both I think.. a photos worth a thousand words Chris Zodiac XLB Sydney Read this topic online here: http://forums.matronics.com/viewtopic.php?p=310779#310779


    Message 2


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 07:34:56 AM PST US
    Subject: Re: center spar upgrade 6ZU 3-2
    From: "DaveG601XL" <david.m.gallagher@ge.com>
    Chris, I installed it per your first assumption. I placed 6ZU3-2 against the skin and under all surrounding uprights and stiffeners. Picture attached. Good luck, -------- David Gallagher 601 XL/Jabiru 3300 First flight 7/24/08 Upgraded 3/19/10 150+ hours and climbing! Read this topic online here: http://forums.matronics.com/viewtopic.php?p=310805#310805 Attachments: http://forums.matronics.com//files/upgrade_19_113.jpg


    Message 3


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 08:00:57 AM PST US
    From: Afterfxllc@aol.com
    Subject: Re: center spar upgrade 6ZU 3-2
    Hey David did you change your aft uprights also? Jeff In a message dated 8/31/2010 10:35:33 A.M. Eastern Daylight Time, david.m.gallagher@ge.com writes: http://forums.matronics.com//files/upgrade_19_113.jpg


    Message 4


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 08:54:46 AM PST US
    Subject: Re: center spar upgrade 6ZU 3-2
    From: "DaveG601XL" <david.m.gallagher@ge.com>
    Jeff, My aft upright is still the original one. -------- David Gallagher 601 XL/Jabiru 3300 First flight 7/24/08 Upgraded 3/19/10 150+ hours and climbing! Read this topic online here: http://forums.matronics.com/viewtopic.php?p=310821#310821


    Message 5


  • INDEX
  • Back to Main INDEX
  • PREVIOUS
  • Skip to PREVIOUS Message
  • NEXT
  • Skip to NEXT Message
  • LIST
  • Reply to LIST Regarding this Message
  • SENDER
  • Reply to SENDER Regarding this Message
    Time: 07:17:19 PM PST US
    Subject: Re: center spar upgrade 6ZU 3-2
    From: "Ron Lendon" <ron.lendon@gmail.com>
    FWIW, I puzzled over this also and called Caleb at Zenith. Here is a picture of the outcome of that conversation on mykitlog. http://mykitlog.com/users/display_log.php?user=rlendon&project=780&category=0&log=101653&row=7 I was able to drive the part up from below, the most puzzling part was did the verticle spar get sandwiched or not. Caleb and I agreed that it should be sandwiched. I noticed Dave made it the other way, and I'm sure it's fine that way also. I just think, and Caleb agreed, the sandwiched joint it makes a stronger junction. -------- Ron Lendon, Clinton Township, MI WW Corvair with Roy's Garage 5th bearing Zodiac XL, ScrapBuilder ;-) http://www.mykitlog.com/rlendon Read this topic online here: http://forums.matronics.com/viewtopic.php?p=310879#310879




    Other Matronics Email List Services

  • Post A New Message
  •   zenith601-list@matronics.com
  • UN/SUBSCRIBE
  •   http://www.matronics.com/subscription
  • List FAQ
  •   http://www.matronics.com/FAQ/Zenith601-List.htm
  • Web Forum Interface To Lists
  •   http://forums.matronics.com
  • Matronics List Wiki
  •   http://wiki.matronics.com
  • 7-Day List Browse
  •   http://www.matronics.com/browse/zenith601-list
  • Browse Zenith601-List Digests
  •   http://www.matronics.com/digest/zenith601-list
  • Browse Other Lists
  •   http://www.matronics.com/browse
  • Live Online Chat!
  •   http://www.matronics.com/chat
  • Archive Downloading
  •   http://www.matronics.com/archives
  • Photo Share
  •   http://www.matronics.com/photoshare
  • Other Email Lists
  •   http://www.matronics.com/emaillists
  • Contributions
  •   http://www.matronics.com/contribution

    These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.

    -- Please support this service by making your Contribution today! --