Today's Message Index:
----------------------
1. 06:06 AM - Re: stainles steel rivets SS (Garry Williams)
2. 06:47 AM - Re: stainles steel rivets SS (Afterfxllc@aol.com)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: stainles steel rivets SS |
I may be incorrect on this but I would swear that I remember some mention of
SS rivets on the Rudder Horn area?
On Thu, Nov 25, 2010 at 10:19 PM, Terry Phillips <ttp44@rkymtn.net> wrote:
>
> Hi Chris
>
> I don't have a complete list, but the ones I know for sure are the 4 shown
> on Dwg. 6T3 (rev. 03/06). There may be others that I have not yet
> encountered. I don't know how many spares Zenair included in the kit.
>
> Terry
>
>
> At 06:06 PM 11/25/2010 -0800, you wrote:
>
>> Gang just cleaning up the last of my metal work building stage and
>> discovered 5 A4 SS rivets left over.
>>
>> has anyone got a list of where the SS rivets should go in the XL and I can
>> check that I have used the correct ones as required and that these are
>> spares..
>>
>> Chris.
>>
>>
>>
>>
>
> Terry Phillips
> ttp44~at~rkymtn.net
> Corvallis MT
> ZU-601XL/Jab 3300 s .. l .. o .. o .. w build kit - Tail & flaps are done;
> Upgrading wings & ailerons per the AMD Safety Directive
> http://www.mykitlog.com/N47TP/
>
>
--
Garry Williams
EAA - 1031 - www.Corvair-Flier.com <http://www.corvair-fflier.com/>
Corvair Powered - 601XL-B Scratch Builder
Edinburg, VA
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: stainles steel rivets SS |
You use 2 SS rivets in the strap that goes between the upper and lower
Elevator Horn. the strap was added to remove any flexing of the skin.
Jeff
In a message dated 11/26/2010 9:07:21 A.M. Eastern Standard Time,
corvair.flier@gmail.com writes:
I may be incorrect on this but I would swear that I remember some mention
of SS rivets on the Rudder Horn area?
On Thu, Nov 25, 2010 at 10:19 PM, Terry Phillips <_ttp44@rkymtn.net_
(mailto:ttp44@rkymtn.net) > wrote:
(mailto:ttp44@rkymtn.net) >
Hi Chris
I don't have a complete list, but the ones I know for sure are the 4 shown
on Dwg. 6T3 (rev. 03/06). There may be others that I have not yet
encountered. I don't know how many spares Zenair included in the kit.
Terry
At 06:06 PM 11/25/2010 -0800, you wrote:
Gang just cleaning up the last of my metal work building stage and
discovered 5 A4 SS rivets left over.
has anyone got a list of where the SS rivets should go in the XL and I can
check that I have used the correct ones as required and that these are
spares..
Chris.
Terry Phillips
ttp44~at~_rkymtn.net_ (http://rkymtn.net/)
Corvallis MT
ZU-601XL/Jab 3300 s .. l .. o .. o .. w build kit - Tail & flaps are done;
Upgrading wings & ailerons per the AMD Safety Directive
_http://www.mykitlog.com/N47TP/_ (http://www.mykitlog.com/N47TP/)
ber is the Annual List Fund Raiser. Click on
m/" target="_blank">www.aeroelectric.com
omebuiltHELP _www.homebuilthelp.com_ (http://www.homebuilthelp.com/)
_http:/r generous support!
Matronics List Features Navigator to browse
s.com/Navigator?Zenith601-List"
target="_blank">http://www.matronics.com/Navigator?Zenith601-List_ (http://www.matronics.com/contribution)
ronics.com/" target="_blank">http://forums.matronics.com
=============
--
Garry Williams
EAA - 1031 - _www.Corvair-Flier.com_ (http://www.corvair-fflier.com/)
Corvair Powered - 601XL-B Scratch Builder
Edinburg, VA
(http://www.aeroelectric.com/)
(http://www.buildersbooks.com/)
(http://www.homebuilthelp.com/)
(http://www.matronics.com/contribution)
(http://www.matronics.com/Navigator?Zenith601-List)
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|