Today's Message Index:
----------------------
1. 03:08 AM - OAT Sensor (Ianrat)
2. 06:33 AM - Chat Reminder (George Race)
3. 07:04 AM - Re: OAT Sensor (Jeff)
4. 08:10 AM - Re: OAT Sensor (jaybannist@cs.com)
5. 01:33 PM - Re: OAT Sensor (Bryan Martin)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Where is the best position to install an Out Side Temp Probe on a 601 XL.
Thank you
Ianrat
CH 601 XLB
Brisbane Australia
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=326084#326084
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Live Chat Room every Monday evening around 8:00 EDT
http://www.mykitairplane.com <blocked::http://www.mykitairplane.com/>
Click on the Chat Room link at the top of the page.
George
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Under the saddle in the bulkhead is protected from the direct sun, not
readily visible, and exposed to direct outside air.
Jeff Davidson
-----Original Message-----
From: owner-zenith601-list-server@matronics.com
[mailto:owner-zenith601-list-server@matronics.com] On Behalf Of Ianrat
Sent: Sunday, January 09, 2011 6:05 AM
Subject: Zenith601-List: OAT Sensor
Where is the best position to install an Out Side Temp Probe on a 601 XL.
Thank you
Ianrat
CH 601 XLB
Brisbane Australia do not archive
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=326084#326084
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Ian,
I mounted my OAT probe inside the right NACA intake fiberglass molding. I
figured it would have adequate outside air, not be affected by cowling temp
s nor the exhaust stream and would be out of the sunlight. It is also a sh
ort wiring run from the probe to my Dynon, which has an OAT readout. .
Jay
-----Original Message-----
From: Ianrat <ianrat@powerup.com.au>
Sent: Sun, Jan 9, 2011 5:09 am
Subject: Zenith601-List: OAT Sensor
Where is the best position to install an Out Side Temp Probe on a 601 XL.
Thank you
Ianrat
CH 601 XLB
Brisbane Australia
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=326084#326084
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
That's where I put mine also.
On Jan 9, 2011, at 11:07 AM, jaybannist@cs.com wrote:
> Ian,
>
> I mounted my OAT probe inside the right NACA intake fiberglass molding. I figured
it would have adequate outside air, not be affected by cowling temps nor
the exhaust stream and would be out of the sunlight. It is also a short wiring
run from the probe to my Dynon, which has an OAT readout. .
>
> Jay
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|