Today's Message Index:
----------------------
1. 10:54 AM - seeping header shutoff valve (Larry McFarland)
2. 03:32 PM - Re: seeping header shutoff valve (Bill Naumuk)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | seeping header shutoff valve |
Hi Guys,
This past month an experimental burned up in a t-hangar in Davenport. The
suspected reason was a milk house heater setup that was running on and off
and that he had a leaking fuel system. The 182 in the adjoining hangar and
a boat in the other were both burned. The 182 was written off as totaled.
The fuselage exploded and the heat caused the beams above to sag a little.
Worst of it all was that he had no insurance. None!
Anyway, I realized my heater system was the same as his and my cockpit had
that familiar smell too, so I put my finger around the shutoff fittings and
it was damp. It's the automotive brass cone type with springs that keep it
tight for a year or two. This one was the second I'd replaced, so I went to
the hardware store and bought a ball valve type with a yellow handle
denoting the gas, oil and water compatibility. It took a little while to
drain the tank and get the fittings arranged to keep from re-plumbing
everything and using a piece of the shutoff without the handle. A slight
mod to the valve handle took care of the job.
If you're using one of these brass fitting, take a look at it! The ball
valve types are a much safer bet.
http://www.macsmachine.com/images/controllinkages/full/fuelshutoff2.gif
This week there's no smell and it's dry in there.
I'm flying again with great weather and looking forward to more.
Endorphins are up again.
Do fly safe,
Larry McFarland at www.macsmachine.com
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: seeping header shutoff valve |
On 04/15/2011 01:49 PM, Larry McFarland wrote:
>
> Hi Guys,
>
> This past month an experimental burned up in a t-hangar in Davenport.
> The suspected reason was a milk house heater setup that was running
> on and off and that he had a leaking fuel system. The 182 in the
> adjoining hangar and a boat in the other were both burned. The 182
> was written off as totaled. The fuselage exploded and the heat
> caused the beams above to sag a little. Worst of it all was that he
> had no insurance. None!
>
> Anyway, I realized my heater system was the same as his and my
> cockpit had that familiar smell too, so I put my finger around the
> shutoff fittings and it was damp. It's the automotive brass cone
> type with springs that keep it tight for a year or two. This one was
> the second I'd replaced, so I went to the hardware store and bought a
> ball valve type with a yellow handle denoting the gas, oil and water
> compatibility. It took a little while to drain the tank and get the
> fittings arranged to keep from re-plumbing everything and using a
> piece of the shutoff without the handle. A slight mod to the valve
> handle took care of the job.
>
>
> If you're using one of these brass fitting, take a look at it! The
> ball valve types are a much safer bet.
>
> http://www.macsmachine.com/images/controllinkages/full/fuelshutoff2.gif
>
>
> This week there's no smell and it's dry in there.
>
> I'm flying again with great weather and looking forward to more.
> Endorphins are up again.
>
>
> Do fly safe,
>
>
> Larry McFarland at www.macsmachine.com <http://www.macsmachine.com>
>
>
> *
>
>
> *
Larry-
Please send a picture of the replacement valve.
Bill
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|