Today's Message Index:
----------------------
1. 05:00 PM - CH601-HD(S) fuselage assembly (Carlos Sa)
2. 06:32 PM - Re: CH601-HD(S) fuselage assembly (Jay Bannister)
3. 06:40 PM - Re: CH601-HD(S) fuselage assembly (Carlos Sa)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | CH601-HD(S) fuselage assembly |
Hello, folks
My aluminum stack is finally starting to resemble an aircraft (if you have
a lot of imagination, that is):
http://www.zenith.aero/photo/img-6058
When I put the front side skins in place (just to have an idea of what it
would look like), I noticed the interference between the side skins, heel
support and floor (the rolled end of the floor).
The attached pics show the offending area.
The instructions simply say "trim as required" (or something like that).
To me, it seems I'll have to remove a semi-circle one or two inches in
diameter - as I haven't seen any comments about this, I am a little
concerned.
I also have looked at a few of the CH601 sites still on-line, but I did not
find any picture or comment that would clarify this.
Thanks in advance for your comments / suggestions
Carlos
CH601-HD, plans
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: CH601-HD(S) fuselage assembly |
Carlos,
I'm not sure when it started, but I discovered this problem (with my 601XL)
in June 2006 and reported it to Zenith. They published a revised photo gu
ide page, saying that it had to be trimmed. (I had already done that) I t
hink they revised the part after that, but I really don't know if they ever
revised the drawing for the part.
Jay
-----Original Message-----
From: Carlos Sa <carlossa52@gmail.com>
@matronics.com>
Sent: Sun, Jul 8, 2012 8:05 pm
Subject: Zenith601-List: CH601-HD(S) fuselage assembly
Hello, folks
My aluminum stack is finally starting to resemble an aircraft (if you have
a lot of imagination, that is):
http://www.zenith.aero/photo/img-6058
When I put the front side skins in place (just to have an idea of what it w
ould look like), I noticed the interference between the side skins, heel su
pport and floor (the rolled end of the floor).
The attached pics show the offending area.
The instructions simply say "trim as required" (or something like that).
To me, it seems I'll have to remove a semi-circle one or two inches in diam
eter - as I haven't seen any comments about this, I am a little concerned.
I also have looked at a few of the CH601 sites still on-line, but I did not
find any picture or comment that would clarify this.
Thanks in advance for your comments / suggestions
Carlos
CH601-HD, plans
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: CH601-HD(S) fuselage assembly |
So it happens on the XL as well?!
I'll take a look at XL pics, then
Thanks, Jay
Carlos
On 8 July 2012 21:31, Jay Bannister <jaybannist@cs.com> wrote:
> Carlos,
>
> I'm not sure when it started, but I discovered this problem (with my
> 601XL) in June 2006 and reported it to Zenith. They published a revised
> photo guide page, saying that it had to be trimmed. (I had already done
> that) I think they revised the part after that, but I really don't know if
> they ever revised the drawing for the part.
>
> Jay
>
>
> -----Original Message-----
> From: Carlos Sa <carlossa52@gmail.com>
> To: zenith601-list <zenith601-list@matronics.com>; zenith-list <
> zenith-list@matronics.com>
> Sent: Sun, Jul 8, 2012 8:05 pm
> Subject: Zenith601-List: CH601-HD(S) fuselage assembly
>
> Hello, folks
>
>
> My aluminum stack is finally starting to resemble an aircraft (if you have
> a lot of imagination, that is):
> http://www.zenith.aero/photo/img-6058
>
> When I put the front side skins in place (just to have an idea of what it
> would look like), I noticed the interference between the side skins, heel
> support and floor (the rolled end of the floor).
> The attached pics show the offending area.
> The instructions simply say "trim as required" (or something like that).
> To me, it seems I'll have to remove a semi-circle one or two inches in
> diameter - as I haven't seen any comments about this, I am a little
> concerned.
> I also have looked at a few of the CH601 sites still on-line, but I did
> not find any picture or comment that would clarify this.
>
>
> Thanks in advance for your comments / suggestions
>
>
> Carlos
> CH601-HD, plans
>
>
> *
>
> *
>
>
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|