---------------------------------------------------------- Zenith601-List Digest Archive --- Total Messages Posted Fri 05/02/14: 3 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 02:40 AM - Re: CO (SIDESLIP) 2. 01:47 PM - Nose gear (SUE JANNAKOS) 3. 01:50 PM - Nose gear bottom bearing (SUE JANNAKOS) ________________________________ Message 1 _____________________________________ Time: 02:40:00 AM PST US Subject: Zenith601-List: Re: CO From: "SIDESLIP" Bobby; If it is a slip joint, you have two options. Use NICKEL Anti-Seize, or get Permatex Copper RTV. The local snowmobile race shop here sees unbelievable EGT's and told me the proper way to use this copper RTV silicone. Coat each end with a VERY thin layer of Copper RTV Silicone, let it set up overnight, or longer, then reassemble the parts. He has NEVER had a leak and runs EGTS so high it would scare you! He melts pistons! The exhaust still doesn't leak. Runs 150 shots of nitrous on a 2 cyl sled engine. These guys are making obscene power and using this method, their exhaust doesn't leak! I have a brand new exhaust, and just used the Nickel Anti seize and no leaks. Here is what I've been told where everyone goes wrong. They assemble the exhaust systems without ANY sort of lubrication at these joints, and in very short time they wear out, and or seize, causing the exhaust to crack. Once a year I am going to disassemble my exhaust and clean up the slip joints and coat them with a new batch of Nickel anti seize. This stuff is designed for 1500 degrees and up. The copper anti size used on brakes on your car isn't good enough. Hope this helps!! Chad -------- C-GYXQ. 912ULS. 601XL-B Read this topic online here: http://forums.matronics.com/viewtopic.php?p=422720#422720 ________________________________ Message 2 _____________________________________ Time: 01:47:00 PM PST US From: SUE JANNAKOS Subject: Zenith601-List: Nose gear I need to replace the nose gear bungee cord on my 601 HDS N4399, SN 6-4211 My question is: 6-G-2-1 Nose gear bottom bearing for 601-XL 6-F-10-1 Nose gear stop for 601-HD/HDS Can I replace the 6-F-10-1 nose gear stop with the 6-G-2-1 Nose gear bottom bearing? Is sowhat is the cost of the nose gear bottom bearing? =C2- thanks, Greg Jannakos ________________________________ Message 3 _____________________________________ Time: 01:50:05 PM PST US From: SUE JANNAKOS Subject: Zenith601-List: Nose gear bottom bearing Looking for help with my nose gear and replacing the bungee cord. 6-G-2-1 Nose gear bottom bearing for 601-XL 6-F-10-1 Nose gear stop for 601-HD/HDS Can I replace the 6-F-10-1 nose gear stop with the 6-G-2-1 Nose gear bottom bearing? ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message zenith601-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Zenith601-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/zenith601-list Browse Digests http://www.matronics.com/digest/zenith601-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.