Today's Message Index:
----------------------
 
     1. 06:18 AM - Re: Phase 1 Flight Report (steveadams)
     2. 01:32 PM - Dimensioning Question (Scott Stewart)
     3. 11:01 PM - Re: Dimensioning Question (Scott Stewart)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
06:18:41 AM PST US
Subject: 
Re: Phase 1 Flight Report
From: 
"steveadams" <dr_steve_adams@yahoo.com>
      
      
      Congratulations, I was wondering how the first flights went. Have fun and be careful.
      
      Steve
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=263664#263664
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
01:32:26 PM PST US
Subject: 
Dimensioning Question
From: 
"Scott Stewart" <scott_stewart@agilent.com>
      
      
      Hi All,
      
      I am trying to position the F4-3 horizontal tail attach plates.  On page F4 of
      the plans, it shows a vertical dimension of 150 mm from the centerline of the
      rivets into the upper longeron to the centerline of the F4-3 horizontal tail attach
      plate.  Yet this puts the attach plate low in the opening between the upper
      and lower rear side skins.  To center the attach plate in this opening, this
      dimension should be closer to 135 mm.
      
      I have found a couple of places in my new computer-generated plans where the dimensions
      were typed incorrectly during the transition, and I am concerned this
      is another case.
      
      Could someone help confirm the vertical dimension to use for positioning the plates?
      Thanks!
      
      --------
      Scott Stewart
      s/n: 0092
      Building from plans
      Rudder and Stabilator complete.  Wings at 65%.  Fuselage at 40%.
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=263730#263730
      
      

Message 3


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
11:01:20 PM PST US
Subject: 
Re: Dimensioning Question
From: 
"Scott Stewart" <scott_stewart@agilent.com>
      
      
      Please disregard the last question.  I calculated the correct distance to be 143
      mm from the top of the upper longerons based on the required stabilator deflections
      shown on page M50 and the position of the F27 stops.
      
      --------
      Scott Stewart
      s/n: 0092
      Building from plans
      Rudder and Stabilator complete.  Wings at 65%.  Fuselage at 40%.
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=263793#263793
      
      








Other Matronics Email List Services




Post A New Message
  
zenith640-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/Zenith640-List.htm
Web Forum Interface To Lists
  
http://forums.matronics.com
Matronics List Wiki
  
http://wiki.matronics.com
7-Day List Browse
  
http://www.matronics.com/browse/zenith640-list
Browse Zenith640-List Digests
  
http://www.matronics.com/digest/zenith640-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --