Today's Message Index:
----------------------
1. 04:52 AM - Re: CAD disk and new Photos (super58d)
2. 10:03 AM - Re: CAD disk and new Photos (pilot4pay)
3. 03:59 PM - Re: CAD disk and new Photos (super58d)
4. 04:42 PM - Flap ribs (super58d)
Message 1
INDEX | Back to Main INDEX |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: CAD disk and new Photos |
Hey Craig,
Sorry for the long span in between replies. We had a lot going on there at the
end of our deployment and a family emergency didn't help either. But, I'm finally
back home and building again. Yay!! Anyway, I'm running Adobe reader 9
and Windows Vista Home Premium. I haven't had any trouble opening the photos
on the disk. Some are standard JPEG images while others are put together into
the pdfs as you know. There are a lot of very useful new photos. Just last night
I was using them to reference the wing bellcrank assembly. (the directions
weren't crystal clear) Whoever took the pics did a good job because they address
all the right areas where questions might arise. I included as an attachment
one of the smaller pdf files for the back seat/ luggage compartment so you can
see if it opens on your computer. Hope this helps.
--------
Mark
s/n 094
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=322729#322729
Attachments:
http://forums.matronics.com//files/rear_seat_installation_159.pdf
Message 2
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: CAD disk and new Photos |
Thanks for getting back with us. The pdf opened fine for me, What kinds of CAD
drawings are in the disc?
I'll probably purchase the disc after I get my truck sold.
By the way, I've been posting lots of pics to the Zenith builders and flyers club,
they now even have a 640 group.
Sorry to hear about your tribulations, hope things have settled down for you. Have
a wonderful Christmas, and we all thank you for your service to our country.
--------
Craig Smith
CH640 builder
SN: 0078
"Just think how stupid the average person is,
and then realize that half of them are even stupider!"
--George Carlin
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=322755#322755
Message 3
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Subject: | Re: CAD disk and new Photos |
Well, I looked pretty thoroughly and haven't found any CAD drawings on the disk
yet. There are a lot of JPEG pics, .pdf files with pics and links to an explorer
(or firefox, that's what I use) type browser that links all the photos through
a menu tree of sorts. They did send a whole new set of drawings though. I
haven't compared page by page with the ones I already had, but they look pretty
much the same to me. If there's a difference between the two I haven't found
them yet. The new photos are certain worth paying for, but if they charged that
much money for a few photos and a new bundle of papers, that seems a bit excessive.
I haven't had the time to look further into it yet, so I've been trying
to be blissfully ignorant and not worry about it.
--------
Mark
s/n 094
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=322786#322786
Message 4
INDEX | Back to Main INDEX |
PREVIOUS | Skip to PREVIOUS Message |
NEXT | Skip to NEXT Message |
LIST | Reply to LIST Regarding this Message |
SENDER | Reply to SENDER Regarding this Message |
|
Ok, so I'm a bit lost on the wing flap ribs and their placement. I sorted them
all out using the plans, but think I was sent too many of one side and not enough
of the other. I was wondering if it matters which way the inside flap ribs
face. The outside ones (ribs 1 and 7) on both side are opposite each other and
look ok. The inside ones however all point one way on the left flap. On the
right flap most of them point the same way as the left flap with the exception
of one, it faces the other way. I took a square and made sure I had the 90 degree
angle on top so the angled portion is on the bottom as they lie on the bench.
I included a pic to show how I have them laid out. Anyone know how these
are supposed to be installed within the skins?
--------
Mark
s/n 094
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=322791#322791
Attachments:
http://forums.matronics.com//files/flap_rib_placement_102.jpg
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|