Today's Message Index:
----------------------
 
     1. 03:56 PM - Re: Flap ribs (super58d)
     2. 04:17 PM - Re: Flap ribs (pilot4pay)
 
 
 

Message 1


					INDEX
 Back to Main INDEX
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
03:56:24 PM PST US
Subject: 
Re: Flap ribs
From: 
"super58d" <smarkburrows@gmail.com>
      
      
      Thanks Craig,
        By looking at the drawings, it would seem that structurally it shouldn't matter
      which way they face. But the drawings DO specify which way they should go.
      I did call Zenair, but about something else. That was 3 weeks ago and still no
      reply. It is the holidays however and they ran and grabbed a -640 specialist
      to answer my questions. I didn't ask about the flaps because I hadn't realized
      the problem at that point. I am ready to install the ribs into the right flap.
      Everything is pretty straightforward. I'm just being cautious about the hinges.
      I'm not happy with the way they ended up on the stabilator trim tabs. I want
      these to be better, but don't yet have a good method for doing it.
      
      --------
      Mark
      s/n 094
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=325494#325494
      
      

Message 2


					INDEX
 Back to Main INDEX
				PREVIOUS
 Skip to PREVIOUS Message
					NEXT
 Skip to NEXT Message
	LIST
 Reply to LIST Regarding this Message
		SENDER
 Reply to SENDER Regarding this Message

      
      
Time: 
04:17:31 PM PST US
Subject: 
Re: Flap ribs
From: 
"pilot4pay" <pilot4profit@sbcglobal.net>
      
      
      I think I had a similar problem with my trim tabs. I put in the specified shim,
      (actually mine was just a tad thicker) between hinge and tab skin. But the travel
      on the tab side seemed a bit cramped, due to the spring back of the tab skin.
      
      --------
      Craig Smith
      CH640 builder
      SN: 0078
      
      &quot;Just think how stupid the average person is,
      and then realize that half of them are even stupider!&quot;
      --George Carlin
      
      
      Read this topic online here:
      
      http://forums.matronics.com/viewtopic.php?p=325495#325495
      
      








Other Matronics Email List Services




Post A New Message
  
zenith640-list@matronics.com
UN/SUBSCRIBE
  
http://www.matronics.com/subscription
List FAQ
  
http://www.matronics.com/FAQ/Zenith640-List.htm
Web Forum Interface To Lists
  
http://forums.matronics.com
Matronics List Wiki
  
http://wiki.matronics.com
7-Day List Browse
  
http://www.matronics.com/browse/zenith640-list
Browse Zenith640-List Digests
  
http://www.matronics.com/digest/zenith640-list
Browse Other Lists
  
http://www.matronics.com/browse
Live Online Chat!
  
http://www.matronics.com/chat
Archive Downloading
  
http://www.matronics.com/archives
Photo Share
  
http://www.matronics.com/photoshare
Other Email Lists
  
http://www.matronics.com/emaillists
Contributions
  
http://www.matronics.com/contribution









These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.




-- Please support this service by making your Contribution today! --