Today's Message Index:
----------------------
1. 09:35 AM - 701 Rotax Mount (Tommy Walker)
2. 01:25 PM - Flapperon spar location (MacDonald Doug)
3. 09:29 PM - Re: Flapperon spar location (JohnDRead@aol.com)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Listers,
I am looking for a bed style engine mount for a Rotax 912 engine.
prefer unused, but would consider other.
Also looking for cowl.
If you got one, or know anyone with one sitting around, please let me know.
I got the engine, but need a mount.
I would swap a used CZAW 601 mount for one :)
Thanks,
Tommy Walker in Alabama
1.1 701's built....
Do Not Archive
--------
Tommy Walker
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=184754#184754
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Flapperon spar location |
Guys, can one of you kit builders please check a
physical measurment for me. I am re-starting into my
flapperons after taking a couple of month off to work
on my wings. I am not finding an absolute spar rivet
line location from the bottom trailing edge. Can
somebody please measure from the bottom trailing edge
to the factory rivet line on a kit skin? I am scratch
building so I have not got a pre drilled line to base
all of my other measurements on.
On page 7-A-2 it gives a summary of the rivet spacing
and when I add this up I get 174mm. I have a
flapperon made that has this distance and it doesn't
seem correct. It appears the spar is too close to the
nose bend.
Any ideas?
Doug MacDonald
CH-701 Scratch builder
NW Ontario, Canada
Almost ready for Pre-Cover Inspection.
Do Not Archive
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Flapperon spar location |
Doug, I measured a skin and 174 mm is the distance from the TE to the
prepunched rivet line.
John Read
Phone: 303-648-3261
Fax: 303-648-3262
Cell: 719-494-4567
In a message dated 5/25/2008 2:26:07 P.M. Mountain Daylight Time,
dougsnash@yahoo.com writes:
--> Zenith701801-List message posted by: MacDonald Doug
<dougsnash@yahoo.com>
Guys, can one of you kit builders please check a
physical measurment for me. I am re-starting into my
flapperons after taking a couple of month off to work
on my wings. I am not finding an absolute spar rivet
line location from the bottom trailing edge. Can
somebody please measure from the bottom trailing edge
to the factory rivet line on a kit skin? I am scratch
building so I have not got a pre drilled line to base
all of my other measurements on.
On page 7-A-2 it gives a summary of the rivet spacing
and when I add this up I get 174mm. I have a
flapperon made that has this distance and it doesn't
seem correct. It appears the spar is too close to the
nose bend.
Any ideas?
Doug MacDonald
CH-701 Scratch builder
NW Ontario, Canada
Almost ready for Pre-Cover Inspection.
Do Not Archive
**************Get trade secrets for amazing burgers. Watch "Cooking with
Tyler Florence" on AOL Food.
(http://food.aol.com/tyler-florence?video=4&?NCID=aolfod00030000000002)
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|