Today's Message Index:
----------------------
1. 04:38 AM - Posting to Zenith List ()
2. 10:33 AM - 701 Cabin side measurement (Ashcraft, Keith - AES)
3. 11:39 AM - Re: 701 Cabin side measurement (Roy Szarafinski)
4. 12:13 PM - Re: 701 Cabin side measurement (Ashcraft, Keith - AES)
5. 01:47 PM - Re: 701 Cabin side measurement (Ashcraft, Keith - AES)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Posting to Zenith List |
It's great that we now have "our own" list for STOL Zeniths, but let's also keep
it easier to read by sticking to Mat's simple rules--and in particular this
one:
"- When responding, NEVER quote the *entire* original post in your
response. DO use lines from the original post to help "tune in" the
reader to the topic at hand, but be selective. The impact that
quoting the entire original post has on the size of the archive
can not be overstated! "
Yesterday we had two posts that repeated the entire day's digest. Just think of
how many people got "scroll finger fatigue."
Do not archive
Rich Hartwig
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | 701 Cabin side measurement |
701 builders,
Quick question, What is the length along the front of part 7F9-1 to the int
ersection of 7F9-7 (front upright)?
Can some of you scratch builders that have already been past this, or kit b
uilders that have a side to measure help me out.
Here is my problem. On page 7F9, the plans show 7F9-7 intersects/meets 7F9-
8 at 280mm from the front of the cabin side (center of the page drawing)
If I place 7F9-7 at that point, the top edge doesn't line up with the edge
of the cabin side, (between the two R47 radius curves)
If I use 7F9-4 length of 132mm, then 7F9-7 intersects/meets 7F9-8 at 288mm,
or if I use the length of both 7F9-4 and 7F9-5, then 7F9-7 intersects/meet
s 7F9-8 around 868mm.
Hope this is making sense.
I guess, another way of measuring might be, if somebody has a kit-built cab
in side, how far out the front of the cabin side, and up from the bottom, t
o the end of a 730mm-7F9-7?
Thanks,
Keith
CH701--scratch (with questions)
This e-mail and any files transmitted with it may be proprietary and are in
tended solely for the use of the individual or entity to whom they are addr
essed. If you have received this e-mail in error please notify the sender.
Please note that any views or opinions presented in this e-mail are solely
those of the author and do not necessarily represent those of ITT Corporati
on. The recipient should check this e-mail and any attachments for the pres
ence of viruses. ITT accepts no liability for any damage caused by any viru
s transmitted by this e-mail.
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: 701 Cabin side measurement |
Just went and measured mine (plans built) the F9-7 intersects at 284-5 and is flush
with the side between 47 radius curves. The top of 7F9-7 dies onto the .040
cabin side doubler 7F14-6SP and is not critical to assembly (wiggle room)
except maybe when the cabin frame 7F18-1SP butts down to it, I think I had to
trim the bottom of the frame tubes a little when I fit it. Do you have your cabin
cage built?
Roy
----- Original Message ----
From: "Ashcraft, Keith - AES" <Keith.Ashcraft@itt.com>
Sent: Saturday, September 13, 2008 1:32:20 PM
Subject: Zenith701801-List: 701 Cabin side measurement
701 builders,
Quick question, What is the length along the front of part 7F9-1 to the intersection
of 7F9-7 (front upright)?
Can some of you scratch builders that have already been past this, or kit builders
that have a side to measure help me out.
Here is my problem. On page 7F9, the plans show 7F9-7 intersects/meets 7F9-8 at
280mm from the front of the cabin side (center of the page drawing)
If I place 7F9-7 at that point, the top edge doesn't line up with the edge of the
cabin side, (between the two R47 radius curves)
If I use 7F9-4 length of 132mm, then 7F9-7 intersects/meets 7F9-8 at 288mm, or
if I use the length of both 7F9-4 and 7F9-5, then 7F9-7 intersects/meets 7F9-8
around 868mm.
Hope this is making sense.
I guess, another way of measuring might be, if somebody has a kit-built cabin side,
how far out the front of the cabin side, and up from the bottom, to the end
of a 730mm-7F9-7?
Thanks,
Keith
CH701--scratch (with questions)
This e-mail and any files transmitted with it may be proprietary and are intended
solely for the use of the individual or entity to whom they are addressed.
If you have received this e-mail in error please notify the sender.
Please note that any views or opinions presented in this e-mail are solely those
of the author and do not necessarily represent those of ITT Corporation. The
recipient should check this e-mail and any attachments for the presence of viruses.
ITT accepts no liability for any damage caused by any virus transmitted
by this e-mail.
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | 701 Cabin side measurement |
Roy & Stan,
Those measurements are about where I am ending up at. and... No sir Roy, I
do not have my cabin cage built. I am thinking about ordering 4130-welded p
arts from Zenith. I just wasn't sure how much room I had at the firewall en
d to wiggle. Stan's measurements where also what I was coming up with, but
things just didn't seem to be working out.
Thanks again,
Keith
***************************************************************************
***
-----Original Message-----
From: owner-zenith701801-list-server@matronics.com on behalf of Roy Szarafi
nski
Sent: Sat 9/13/2008 12:38 PM
Subject: Re: Zenith701801-List: 701 Cabin side measurement
m>
Just went and measured mine (plans built) the F9-7 intersects at 284-5 and
is flush with the side between 47 radius curves. The top of 7F9-7 dies onto
the .040 cabin side doubler 7F14-6SP and is not critical to assembly (wig
gle room) except maybe when the cabin frame 7F18-1SP butts down to it, I th
ink I had to trim the bottom of the frame tubes a little when I fit it. Do
you have your cabin cage built?
Roy
----- Original Message ----
From: "Ashcraft, Keith - AES" <Keith.Ashcraft@itt.com>
Sent: Saturday, September 13, 2008 1:32:20 PM
Subject: Zenith701801-List: 701 Cabin side measurement
701 builders,
Quick question, What is the length along the front of part 7F9-1 to the int
ersection of 7F9-7 (front upright)?
Can some of you scratch builders that have already been past this, or kit b
uilders that have a side to measure help me out.
Here is my problem. On page 7F9, the plans show 7F9-7 intersects/meets 7F9-
8 at 280mm from the front of the cabin side (center of the page drawing)
If I place 7F9-7 at that point, the top edge doesn't line up with the edge
of the cabin side, (between the two R47 radius curves)
If I use 7F9-4 length of 132mm, then 7F9-7 intersects/meets 7F9-8 at 288mm,
or if I use the length of both 7F9-4 and 7F9-5, then 7F9-7 intersects/meet
s 7F9-8 around 868mm.
Hope this is making sense.
I guess, another way of measuring might be, if somebody has a kit-built cab
in side, how far out the front of the cabin side, and up from the bottom, t
o the end of a 730mm-7F9-7?
Thanks,
Keith
CH701--scratch (with questions)
This e-mail and any files transmitted with it may be proprietary and are in
tended solely for the use of the individual or entity to whom they are addr
essed. If you have received this e-mail in error please notify the sender.
Please note that any views or opinions presented in this e-mail are solely
those of the author and do not necessarily represent those of ITT Corporati
on. The recipient should check this e-mail and any attachments for the pres
ence of viruses. ITT accepts no liability for any damage caused by any viru
s transmitted by this e-mail.
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | 701 Cabin side measurement |
All,
I found my "erorr"(oops) A bad measurement on my part, good thing I
didn't cut any metal until I checked!!!!
Everybody have a good weekend!!!!
Keith
CH701 -- scratch
*************************************************************************
*********************
-----Original Message-----
From: owner-zenith701801-list-server@matronics.com on behalf of
Ashcraft, Keith - AES
Sent: Sat 9/13/2008 1:12 PM
Subject: RE: Zenith701801-List: 701 Cabin side measurement
Roy & Stan,
Those measurements are about where I am ending up at. and... No sir Roy,
I do not have my cabin cage built. I am thinking about ordering
4130-welded parts from Zenith. I just wasn't sure how much room I had at
the firewall end to wiggle. Stan's measurements where also what I was
coming up with, but things just didn't seem to be working out.
Thanks again,
Keith
*************************************************************************
*****
-----Original Message-----
From: owner-zenith701801-list-server@matronics.com on behalf of Roy
Szarafinski
Sent: Sat 9/13/2008 12:38 PM
Subject: Re: Zenith701801-List: 701 Cabin side measurement
<rvickski@yahoo.com>
Just went and measured mine (plans built) the F9-7 intersects at 284-5
and is flush with the side between 47 radius curves. The top of 7F9-7
dies onto the .040 cabin side doubler 7F14-6SP and is not critical to
assembly (wiggle room) except maybe when the cabin frame 7F18-1SP butts
down to it, I think I had to trim the bottom of the frame tubes a little
when I fit it. Do you have your cabin cage built?
Roy
----- Original Message ----
From: "Ashcraft, Keith - AES" <Keith.Ashcraft@itt.com>
Sent: Saturday, September 13, 2008 1:32:20 PM
Subject: Zenith701801-List: 701 Cabin side measurement
701 builders,
Quick question, What is the length along the front of part 7F9-1 to the
intersection of 7F9-7 (front upright)?
Can some of you scratch builders that have already been past this, or
kit builders that have a side to measure help me out.
Here is my problem. On page 7F9, the plans show 7F9-7 intersects/meets
7F9-8 at 280mm from the front of the cabin side (center of the page
drawing)
If I place 7F9-7 at that point, the top edge doesn't line up with the
edge of the cabin side, (between the two R47 radius curves)
If I use 7F9-4 length of 132mm, then 7F9-7 intersects/meets 7F9-8 at
288mm, or if I use the length of both 7F9-4 and 7F9-5, then 7F9-7
intersects/meets 7F9-8 around 868mm.
Hope this is making sense.
I guess, another way of measuring might be, if somebody has a kit-built
cabin side, how far out the front of the cabin side, and up from the
bottom, to the end of a 730mm-7F9-7?
Thanks,
Keith
CH701--scratch (with questions)
This e-mail and any files transmitted with it may be proprietary and are
intended solely for the use of the individual or entity to whom they are
addressed. If you have received this e-mail in error please notify the
sender.
Please note that any views or opinions presented in this e-mail are
solely those of the author and do not necessarily represent those of ITT
Corporation. The recipient should check this e-mail and any attachments
for the presence of viruses. ITT accepts no liability for any damage
caused by any virus transmitted by this e-mail.
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|