Today's Message Index:
----------------------
1. 07:15 AM - Re: Rudder Cable Issues (txpilot)
2. 07:51 AM - Chat Room Reminder For "Digesters" (George Race)
3. 05:24 PM - VW gas guage (ken carp)
4. 06:10 PM - Re: Prop Pitch (carl)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Rudder Cable Issues |
> Dan;
> The lower corner brackets are supposed to be cut away so that the rudder cables
do not rub on them. It is shown in the drawings and in the pictorials.
Yes, thanks John. I did trim those away according to plans. I was referring to
the L brackets those gussets are attached to (that make up most of the airplane).
I was curious if anyone had to trim away the bottom L brackets for the
cable clearance.
Dan
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=218012#218012
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Chat Room Reminder For "Digesters" |
Please join us for the Monday evening chat room starting around 8:00 PM
Eastern Time.
<blocked::blocked::blocked::blocked::blocked::blocked::http://www.mykitairpl
ane.com/chat/> http://www.mykitairplane.com/chat/
George
Do Not Archive
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
I am about to install the VW gas guage in my 750 tank. It looks like it would
be vulnerable to leakage. Has this been much of a problem. It is recommended
to be placed on the side of the tank.
ken
--------
ken carpenter
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=218061#218061
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
I've got a 912 ul with 70" WD 3 blade but my config is Amphibs. I often
fly at or near gross of 1200# and like to set 8.5 to 9.5' as a
compromise for climb and cruise.
This should give you 5100-5200 static on ground.
Carl
----- Original Message -----
From: george.mueller@aurora.org
To: zenith701801-list@matronics.com
Sent: Monday, December 01, 2008 9:41 AM
Subject: Zenith701801-List: Prop Pitch
Is there anyone on this list with a flying 701 with a Rotax 912UL
(80HP) and a warp drive three blade prop? What pitch (measured at the
tips) do you have on the prop and what kind of climb and cruise are you
seeing? With me (230 lbs), my BRS chute and full tanks I am about 50
lbs shy of gross and am seeing 500 fpm climb and 75 mph cruise at about
5400 rpm. Is this normal performance? I only have about 5 degrees
pitch on the prop which gives me 5650 rpm with full throttle in straight
and level flight at about 2000 MSL.
George in Milwaukee
N701GM 55hours flying
CONFIDENTIALITY NOTICE: This email, including any attachments, is for
the sole use of the intended recipient/s and may contain confidential
and privileged information. Any unauthorized review, use, disclosure,
or distribution is prohibited. If you are not the intended recipient,
please contact the sender by phone or return email and destroy all
copies of the original message.
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|