Today's Message Index:
----------------------
1. 02:39 AM - Rotax 912uls 100 HP (Mike Hoffman)
2. 05:08 AM - Re: Rotax 912uls 100 HP (debra EVERETT)
3. 02:09 PM - Question: 7C1-5 hole placement and trimming. (John Marzulli)
4. 04:16 PM - Question: 7C1-5 hole placement and trimming. (John Marzulli)
5. 06:03 PM - Re: Joggles (Tommy Walker)
6. 06:06 PM - Re: Rotax 912uls 100 HP (Tommy Walker)
7. 09:50 PM - Re: Question: 7C1-5 hole placement and trimming. (Craig Payne)
8. 10:12 PM - Landing light cowl location (Victor Menkal)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Rotax 912uls 100 HP |
I'm pretty sure most everyone else that has priced a new Rotax 912 (100hp)
has the same sticker shock as I do. Although the prices have come down a
little because of the devalue of the euro, what or where is the best price
/ place you have found?
Purchase a ROTAX 912uls 100hp engine with hd starter & slipper clutch in
December & pay only $17648.00 . Contact Leading
<http://www.barnstormers.com/contact_seller.php?to=59390&id=294965&title=Rot
ax+912ULS+December+SALE&return=%2FEngines%2B-%2BPiston%2C%2520Rotax%2520Clas
sifieds.html> Edge - LEADING
<http://www.barnstormers.com/contact_seller.php?to=59390&id=294965&title=Rot
ax%20912ULS%20December%20SALE&return=%2FEngines%2B-%2BPiston%2C%2520Rotax%25
20Classifieds.html> EDGE AIR FOILS LLC,
Mike H
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Rotax 912uls 100 HP |
From: mhoffman9@tampabay.rr.comTo: zenith701801-list@matronics.comSubject:
Zenith701801-List: Rotax 912uls 100 HP Date: Sat=2C 20 Dec 2008 05:38:15 -0
500
I=92m pretty sure most everyone else that has priced a new Rotax 912 (100hp
) has the same sticker shock as I do. Although the prices have come down a
little because of the devalue of the euro=2C what or where is the best pr
ice / place you have found?
Purchase a ROTAX 912uls 100hp engine with hd starter & slipper clutch in
December & pay only $17648.00 - Contact Leading Edge - LEADING EDGE AIR F
OILS LLC=2C
Mike H
Mike: I was shocked about the Rotax price also so I bought the Jabiru 2200.
I think it is as good as the Rotax and about $5000 cheaper. I hav e flown
the 701 with the Jabiru and I can't tell a lot of difference in the flignt
chararcteristics. I think it is a simpler
_________________________________________________________________
Send e-mail faster without improving your typing skills.
http://windowslive.com/online/hotmail?ocid=TXT_TAGLM_WL_hotmail_acq_speed
_122008
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Question: 7C1-5 hole placement and trimming. |
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Question: 7C1-5 hole placement and trimming. |
The plans seem pretty vague on page 7C1. I was wondering how other people
have placed the rivet holes in 7C1-5 and trimmed the piece.
First I guessed that to angle the piece that 30mm in on the sides seemed
right with the holes 10mm in from each side. Further interpolation made me
place the two holes 30mm out from the center. The big question is this: Are
the four holes placed 10mm in from the edges?
Does this seem right?
Pic: http://marzulli.smugmug.com/photos/440095676_JBHav-X3.jpg
( Sorry for the repost, but it looks like my first message got mangled )
Thanks, ( and please archive the answer )
John Marzulli
http://www.GenevieveMarzulli.org/
http://marzulli.smugmug.com/
http://701Builder.blogspot.com/
http://www.JohnMarzulli.net/
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
[
Well yes, it will. But perhaps there's a better way?
Merry Christmas and Do Not Archive.
Tommy
quote="rvickski(at)yahoo.com"]Overlapping wont do?
--- On Thu, 12/18/08, Tommy Walker wrote:
> From: Tommy Walker
> Subject: Joggles
> To: zenith701801-list@matronics.com
> Date: Thursday, December 18, 2008, 6:20 PM
> --> Zenith701801-List message
> posted by: "Tommy Walker"
>
> I am looking for a good way to make some joggles where some
> L material intersects. Does anyone have a
> recommendation?
>
> Thanks,
>
>
--------
Tommy Walker
N8701 - Anniston, AL
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=220355#220355
Message 6
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: Rotax 912uls 100 HP |
I bought my first 912 from Zenith... Seems it was a little less expensive. My
second was bought used from a fellow who was parting out his plane.
Do Not Archive
Tommy Walker in Alabama
--------
Tommy Walker
N8701 - Anniston, AL
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=220356#220356
Message 7
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Question: 7C1-5 hole placement and trimming. |
I don't have exact dimensions but I've attached pictures from three
different sources. P1 and P2 are from the Zenith photo guide, P3 is of my
plane and P4 is of George Race's. Hope this helps.
-- Craig
From: owner-zenith701801-list-server@matronics.com
[mailto:owner-zenith701801-list-server@matronics.com] On Behalf Of John
Marzulli
Sent: Saturday, December 20, 2008 5:14 PM
Subject: Zenith701801-List: Question: 7C1-5 hole placement and trimming.
The plans seem pretty vague on page 7C1. I was wondering how other people
have placed the rivet holes in 7C1-5 and trimmed the piece.
First I guessed that to angle the piece that 30mm in on the sides seemed
right with the holes 10mm in from each side. Further interpolation made me
place the two holes 30mm out from the center. The big question is this: Are
the four holes placed 10mm in from the edges?
Does this seem right?
Pic: http://marzulli.smugmug.com/photos/440095676_JBHav-X3.jpg
( Sorry for the repost, but it looks like my first message got mangled )
Thanks, ( and please archive the answer )
John Marzulli
http://www.GenevieveMarzulli.org/
http://marzulli.smugmug.com/
http://701Builder.blogspot.com/
http://www.JohnMarzulli.net/
Message 8
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Landing light cowl location |
Thanx to all who provided ideas and advice on the flush mount fuel caps.
My next burning decision is if I should mount my landing/taxi lights
in the slat or cowl . I like the new LED "pucks" which are suppose
to be vibration resistant, small and low power draw.
I was wondering if anyone with the new style cowl installed on the
their 701 could advise if there is sufficient room to instal 3"
diameter by 1" deep LED lights in the nose of the cowl on either
side of the center line. Seen pics with the old style cowl but not
with the new slimmer cowl.
Thanx Vic
701 tail done skinning wings
Whitehorse Yukon at -35 C yikes!
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|