Today's Message Index:
----------------------
1. 07:37 AM - Dual Sticks (Joenan1934@aol.com)
2. 12:53 PM - Re: Dual Sticks (Dan Wilde)
3. 02:10 PM - Re: Dual Sticks (Ken Arnold)
4. 07:58 PM - Re: Dual Sticks (NYTerminat@aol.com)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Iam about ready to put dual sticks in my 701. You cut the Y stick off at
the connecting point, then weld a 24 inch tube from left to right. Then weld
two upright sticks on top of the horizonial tube. I assume you put the
elevator in zero position then weld the upright sticks. Iam told that the
upright sticks should be moved forward about 20 degrees before you weld them.
Any suggestions? Joseph _joenan1934@aol.com_
(mailto:joenan1934@aol.com)
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Joenan1934@aol.com wrote:
> Iam about ready to put dual sticks in my 701. You cut the Y stick off
> at the connecting point, then weld a 24 inch tube from left to right.
> Then weld two upright sticks on top of the horizonial tube. I assume
> you put the elevator in zero position then weld the upright sticks.
> Iam told that the upright sticks should be moved forward about 20
> degrees before you weld them. Any suggestions? Joseph
> joenan1934@aol.com <mailto:joenan1934@aol.com>
>
> ------------------------------------------------------------------------
> *
> Why do you want dual sticks? The Y stick works great from either side.
> *
Dan Wilde
N948DW
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Dual sticks look great! Suggest you install a hinge near floor on each
stick with locking pin to fold the stick down on ingress and egress.
Send us pics when installed.
Ken
do not archive
----- Original Message -----
From: "Dan Wilde" <dwilde@clearwire.net>
Sent: Tuesday, August 18, 2009 3:47 PM
Subject: Re: Zenith701801-List: Dual Sticks
>
> Joenan1934@aol.com wrote:
>> Iam about ready to put dual sticks in my 701. You cut the Y stick off at
>> the connecting point, then weld a 24 inch tube from left to right. Then
>> weld two upright sticks on top of the horizonial tube. I assume you put
>> the elevator in zero position then weld the upright sticks. Iam told that
>> the upright sticks should be moved forward about 20 degrees before you
>> weld them. Any suggestions? Joseph joenan1934@aol.com
>> <mailto:joenan1934@aol.com>
>>
>> ------------------------------------------------------------------------
>> *
>> Why do you want dual sticks? The Y stick works great from either side.
>> *
>
> Dan Wilde
> N948DW
>
>
>
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
Why would you want to do two sticks? Have you flown with the " Y" STICK?
Bob Spudis
In a message dated 8/18/2009 10:38:11 A.M. Eastern Daylight Time,
Joenan1934@aol.com writes:
Iam about ready to put dual sticks in my 701. You cut the Y stick off at
the connecting point, then weld a 24 inch tube from left to right. Then
weld two upright sticks on top of the horizonial tube. I assume you put the
elevator in zero position then weld the upright sticks. Iam told that the
upright sticks should be moved forward about 20 degrees before you weld them.
Any suggestions? Joseph _joenan1934@aol.com_
(mailto:joenan1934@aol.com)
____________________________________
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|