Today's Message Index:
----------------------
1. 06:22 AM - Re: EGT probe locations for 912S with Zenith exhaust? (jf3sb)
2. 08:38 AM - Chat Reminder for "Digesters" (George Race)
3. 08:39 AM - Re: Re: EGT probe locations for 912S with Zenith exhaust? (Mark Sherman)
4. 10:37 PM - Out of the garage... (John Marzulli)
5. 10:50 PM - Out of the garage... (John Marzulli)
Message 1
| INDEX | Back to Main INDEX |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: EGT probe locations for 912S with Zenith exhaust? |
Sounds like you've got a good working installation that the rest of us strap-hangers
can copy, Mark. Did you mount the probes at the Rotax's specified distance
(even if on a curved part of the header), or move them downstream to a straight
spot?
Thanks...
John
Read this topic online here:
http://forums.matronics.com/viewtopic.php?p=289488#289488
Message 2
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Chat Reminder for "Digesters" |
Live Chat Room every Monday evening around 8:00 EDT
www.mykitairplane.com <blocked::http://www.mykitairplane.com/>
Click on the Chat Room link at the top of the page.
George
Message 3
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Re: EGT probe locations for 912S with Zenith exhaust? |
John.
I tried to use the specified distance. It seems simple enough until you
start to measure on the curve. Do I measure the ID of the tube bend or the
OD of the tube bend? I chose to drill the hole so the tip of the probe came
out 70mm down the center line of the bend from the exhaust flange.
I also use CHT probes, located at the Rotax recommended place. Even though
that isn't a true CHT, because the probe is in a water jacket. Some combo
of water temp and CHT I guess. But that is what they use for the max CHT
measurement location. I also installed a water temp probe located in the
water line as it leaves the top of the cylinders, the hottest point.
Mark S.
701/912ULS
----- Original Message -----
From: "jf3sb" <jf3sb@yahoo.com>
Sent: Sunday, March 07, 2010 6:18 AM
Subject: Zenith701801-List: Re: EGT probe locations for 912S with Zenith
exhaust?
>
> Sounds like you've got a good working installation that the rest of us
> strap-hangers can copy, Mark. Did you mount the probes at the Rotax's
> specified distance (even if on a curved part of the header), or move them
> downstream to a straight spot?
>
> Thanks...
>
> John
>
>
> Read this topic online here:
>
> http://forums.matronics.com/viewtopic.php?p=289488#289488
>
>
>
Message 4
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Out of the garage... |
... and into a hangar!
http://marzulliphoto.net/Airplanes/To-The-Hangar/11450052_vpqfS#805113399_shyuK
John Marzulli
http://www.GenevieveMarzulli.org/
http://MarzulliPhoto.net/
http://701Builder.blogspot.com/
Message 5
| INDEX | Back to Main INDEX |
| PREVIOUS | Skip to PREVIOUS Message |
| NEXT | Skip to NEXT Message |
| LIST | Reply to LIST Regarding this Message |
| SENDER | Reply to SENDER Regarding this Message |
|
| Subject: | Out of the garage... |
... and into a hangar!
http://marzulliphoto.net/Airplanes/To-The-Hangar/11450052_vpqfS#805113399_shyuK
John Marzulli
http://www.GenevieveMarzulli.org/
http://MarzulliPhoto.net/
http://701Builder.blogspot.com/
Other Matronics Email List Services
These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.
-- Please support this service by making your Contribution today! --
|