---------------------------------------------------------- Zenith701801-List Digest Archive --- Total Messages Posted Wed 03/17/10: 4 ---------------------------------------------------------- Today's Message Index: ---------------------- 1. 02:19 AM - Re: dent removal question (Mike Hoffman) 2. 10:58 AM - Re: dent removal question (Les Goldner) 3. 12:13 PM - Fuel Filler Trim Ring (George Race) 4. 02:29 PM - Is the owner of 701YY on this list? (John Marzulli) ________________________________ Message 1 _____________________________________ Time: 02:19:17 AM PST US Subject: Zenith701801-List: Re: dent removal question From: "Mike Hoffman" Jimmy, I once ordered a new panel for a Piper aircraft that arrived with a large bend and dent. I went to a old car restoration shop that did custom hot rod work and asked them if they could help me out. The owner looked at the piece and said no problem. We went to the back of his shop where he had a big English Wheel. He proceeded to fix the panel like new. It took him all of about 3 minuets and did not charge me anything. Read this topic online here: http://forums.matronics.com/viewtopic.php?p=290560#290560 ________________________________ Message 2 _____________________________________ Time: 10:58:10 AM PST US From: "Les Goldner" Subject: RE: Zenith701801-List: dent removal question When I ran a slat into the barn door I couldn't get the entire dent out. The more I worked at it the worse it looked. Rather than replace the slat I simply put a rectangular patch of .016 skin over the dent with a few rivets. It looks a lot better than the dent did. Les -----Original Message----- From: owner-zenith701801-list-server@matronics.com [mailto:owner-zenith701801-list-server@matronics.com] On Behalf Of BokKat Sent: Tuesday, March 16, 2010 3:26 PM Subject: Re: Zenith701801-List: dent removal question I hit a small bird with the slats off my wing and dented in a leading edge. Anyone have any ideas? I might try the heating/dry ice cooling thing. It wouldn't do any harm I guess. I always wonder if heavier aluminum on the leading edge might help to prevent some of those dings. After all, we are not flying at mach speeds. Still, more weight..... ----- Original Message ----- From: "George Race" Sent: Tuesday, March 16, 2010 1:56 PM Subject: RE: Zenith701801-List: dent removal question > > > Hi Jimmy: > > After you get as much as you can with the "spoon" technique try heating > the > area up around the dent, including the dent, and then using dry ice, > rubbing > it across the dent, will sometimes shrink the metal enough to remove the > "Soft" dents. Those are dents without sharp protruding edges. > > I hate it what some dumb that that happens. I think we have all been > there > at one time or another. > George > > -----Original Message----- > From: owner-zenith701801-list-server@matronics.com > [mailto:owner-zenith701801-list-server@matronics.com] On Behalf Of Jimmy > Young > Sent: Tuesday, March 16, 2010 11:38 AM > To: zenith701801-list@matronics.com > Subject: Zenith701801-List: dent removal question > > > > Hi Builders, > I'm actually building a 750, but that list isn't as active as this one is. > My problem is I let a 2x4 drop on my nose skin sheet which put a nice > indention in it. The sheet is not installed, so I can work both sides. > I've been told a metal spoon wrapped in tape is used to smooth out the > sheets, and I've done that before on some minor dings. I may not be able > to > get all of this one out, but any advice on techniques will be appreciated! > > Jimmy Young > building a 750 > Houston TX > > -------- > Jimmy Young > Missouri City, TX > Kolb FS II/HKS 700 > > > Read this topic online here: > > http://forums.matronics.com/viewtopic.php?p=290452#290452 > > > ________________________________ Message 3 _____________________________________ Time: 12:13:23 PM PST US From: "George Race" Subject: Zenith701801-List: Fuel Filler Trim Ring Thanks to help from 750 builder Jimmy Young, I now have available a nice Fuel Tank Filler Trim Ring. See my web site for details. www.mykitairplane.com George ________________________________ Message 4 _____________________________________ Time: 02:29:28 PM PST US Subject: Zenith701801-List: Is the owner of 701YY on this list? From: John Marzulli My project is a hangar away from you. I would love to chat with you in person. Thanks, John Marzulli http://www.GenevieveMarzulli.org/ http://MarzulliPhoto.net/ http://701Builder.blogspot.com/ ------------------------------------------------------------------------------------- Other Matronics Email List Services ------------------------------------------------------------------------------------- Post A New Message zenith701801-list@matronics.com UN/SUBSCRIBE http://www.matronics.com/subscription List FAQ http://www.matronics.com/FAQ/Zenith701801-List.htm Web Forum Interface To Lists http://forums.matronics.com Matronics List Wiki http://wiki.matronics.com Full Archive Search Engine http://www.matronics.com/search 7-Day List Browse http://www.matronics.com/browse/zenith701801-list Browse Digests http://www.matronics.com/digest/zenith701801-list Browse Other Lists http://www.matronics.com/browse Live Online Chat! http://www.matronics.com/chat Archive Downloading http://www.matronics.com/archives Photo Share http://www.matronics.com/photoshare Other Email Lists http://www.matronics.com/emaillists Contributions http://www.matronics.com/contribution ------------------------------------------------------------------------------------- These Email List Services are sponsored solely by Matronics and through the generous Contributions of its members.